In this paper, we investigate the performance of maximum ratio combining (MRC) in the presence of multiple cochannel interferences over a flat Rayleigh fading channel. Closed-form expressions of signal-to-interference-plus-noise ratio (SINR), outage probability, and average symbol error rate (SER) of quadrature amplitude modulation (QAM) with M-ary signaling are obtained for unequal-power interference-to-noise ratio (INR). We also provide an upper-bound for the average SER using moment generating function (MGF) of the SINR. Moreover, we quantify the array gain loss between pure MRC (MRC system in the absence of CCI) and MRC system in the presence of CCI. Finally, we verify our analytical results by numerical simulations.

In this paper, a new fractional sample rate conversion (SRC) scheme based on a direct insertion/cancellation scheme is proposed. This scheme is suitable for signals that are sampled at a high sample rate and converted to a lower sample rate. The direct insertion/cancellation scheme may achieve low-complexity and lower power consumption as compared to the other SRC techniques. However, the direct insertion/cancellation technique suffers from large aliasing and distortion. The aliasing from an adjacent channel interferes the desired signal and degrades the performance. Therefore, a modified direct insertion/cancellation scheme is proposed in order to realize high performance resampling.

Introducing multi-agent (MA) technology into a SCADA (Supervisory Control and Data Acquisition) system can improve the serviceability and enhance maintenance-free operation with the inter-terminal parameter (ITP) method. In addition, the system's distributed intelligent field terminals (IFTs) use a common algorithm that is unaffected by any changes to the system specifications. As a result of these innovations, the proposed system has much better serviceability because it is much easier to make modifications compared to that of conventional systems. This system has been implemented for practical purposes at over 60 sites.

An optical CDMA (OCDMA) system is a flexible technology for future broadband multiple access networks. A secure OCDMA network in broadband optical access technologies is also becoming an issue of great importance. In this paper, we propose novel reconfigurable wavelength-time (W-T) optical codes that lead to secure transmission in OCDMA networks. The proposed W-T optical codes are constructed by using quasigroups (QGs) for wavelength hopping and one-dimensional optical orthogonal codes (OOCs) for time spreading; we call them QGs/OOCs. Both QGs and OOCs are randomly generated by a computer search to ensure that an eavesdropper could not improve its interception performance by making use of the coding structure. Then, the proposed reconfigurable QGs/OOCs can provide more codewords, and many different code set patterns, which differ in both wavelength and time positions for given code parameters. Moreover, the bit error probability of the proposed codes is analyzed numerically. To realize the proposed codes, a secure system is proposed by employing reconfigurable encoders/decoders based on array waveguide gratings (AWGs), which allow the users to change their codeword patterns to protect against eavesdropping. Finally, the probability of breaking a certain codeword in the proposed system is evaluated analytically. The results show that the proposed codes and system can provide a large codeword pattern, and decrease the probability of breaking a certain codeword, to enhance OCDMA network security.

A fuzzy logic control battery equalizing controller (FLC-BEC) is adopted to control the cell voltage balancing process for a series connected Li-ion battery string. The proposed individual cell equalizer (ICE) is based on the bidirectional Cuk converter operated in the discontinuous capacitor voltage mode (DCVM) to reduce the switching loss and improve equalization efficiency. The ICE with the proposed FLC-BEC can reduce the equalizing time, maintain safe operations during the charge/discharge state and increase the battery string capacity.

The ability to recognize quickly inside network flows to be executable is prerequisite for malware detection. For this purpose, we introduce an instruction transition probability matrix (ITPX) which is comprised of the IA-32 instruction sets and reveals the characteristics of executable code's instruction transition patterns. And then, we propose a simple algorithm to detect executable code inside network flows using a reference ITPX which is learned from the known Windows Portable Executable files. We have tested the algorithm with more than thousands of executable and non-executable codes. The results show that it is very promising enough to use in real world.

Augmented reality tasks require a high-reliability tracking method. Large tracking error causes many problems during AR applications. Tracking error estimation should be integrated with them to improve the reliability of tracking methods. Although some tracking error estimation methods have been developed, they are not feasible to be integrated because of computational speed and accuracy. For this study, a tracking error estimation algorithm with screen error estimation based on the characteristic of linecode marker was applied. It can rapidly estimate tracking error. An evaluation experiment was conducted to compare the estimated tracking error and the actual measured tracking error. Results show that the algorithm is reliable and sufficiently fast to be used for real-time tracking error warning or tracking accuracy improvement methods.

A fast algorithm to speed up the search process of vector quantization encoding is presented. Using the sum and the partial norms of a vector, some eliminating inequalities are constructeded. First the inequality based on the sum is used for determining the bounds of searching candidate codeword. Then, using an inequality based on subvector norm and another inequality combining the partial distance with subvector norm, more unnecessary codewords are eliminated without the full distance calculation. The proposed algorithm can reject a lot of codewords, while introducing no extra distortion compared to the conventional full search algorithm. Experimental results show that the proposed algorithm outperforms the existing state-of-the-art search algorithms in reducing the computational complexity and the number of distortion calculation.

In AlGaN/GaN high electron mobility transistors (HEMTs), drain current reduction by current collapse phenomenon is a big obstacle for a high efficient operation of power amplifier application. In this study, we investigated the effects of SiN passivation film quality on the electrical characteristics of AlGaN/GaN HEMTs. First, we conducted some experiments to investigate the relationship between electrical characteristics of AlGaN/GaN HEMTs and various conditions of SiN passivation film by plasma enhanced chemical vapor deposition (PE-CVD). We found that both gate current leakage and current collapse were improved simultaneously by SiN passivation film deposited by optimized condition of NH3 and SiH4 gas flow. It is found that the critical parameter in the optimization is a IN-H/ ISi-H ratio measured by Fourier transforms infrared spectroscopy (FT-IR) spectra. Next, a thermal CVD SiN was applied to the passivation film to be investigated from the same point of view, because a thermal CVD SiN is well known to have good quality with low hydrogen content and high IN-H/ISi-H ratio. We confirmed that the thermal CVD SiN passivation could improve much further both of the gate leakage current and the current collapse in AlGaN/GaN-HEMTs. Furthermore, we tried to apply the thermal CVD SiN to the gate insulator in MIS (Metal Insulator Semiconductor) structure of AlGaN/GaN HEMTs. The thermal CVD SiN passivation was more suitable for the gate insulator than PE-CVD SiN passivation in a view of reducing current collapse phenomena. It could be believed that the thermal CVD SiN film is superior to the PE-CVD SiN film to achieve good passivation and gate insulator film for AlGaN/GaN HEMTs due to the low hydrogen content and the high IN-H/ISi-H ratio.

This paper will review the development of SiC power devices especially SiC power junction field-effect transistors (JFETs). Rationale and different approaches to the development of SiC power JFETs will be presented, focusing on normally-OFF power JFETs that can provide the highly desired fail-save feature for reliable power switching applications. New results for the first demonstration of SiC Power ICs will be presented and the potential for distributed DC-DC power converters at frequencies higher than 35 MHz will be discussed.

The performance of recently developed Large Signal (LS) HBT model was evaluated with extensive LS measurements like Power spectrum, Load pull and Inter-modulation investigations. Proposed model has adopted temperature dependent leakage resistance and a simplified capacitance models. The model was implemented in ADS as SDD. Important feature of the model is that the main model parameters are taken directly from measurements in rather simple and understandable way. Results show good accuracy despite the simplicity of the model. To our knowledge the HBT model is one of a few HBT models which can handle high current & Power HBT devices, with significantly less model parameters with good accuracy.

We have fabricated AlGaN/GaN HEMTs with a thin InGaN cap layer to implement normally-off HEMTs with a small extrinsic source resistance. The key idea is to employ the polarization-induced field in the InGaN cap layer, by which the conduction band is raised leading to the normally-off operation. Fabricated HEMT with an In0.2Ga0.8N cap layer with a thickness of 5 nm showed normally-off operation with a threshold voltage of 0.4 V and a maximum transconductance of 85 mS/mm for the device with a 1.9-µm-long gate. By etching-off the In0.2Ga0.8N cap layer at the region except under the gate using gate and ohmic electrodes as etching masks, the sheet resistance has decreased from 2.7 to 0.75 kΩ/, and the maximum transconductance has increased from 85 to 130 mS/mm due to a reduction of the extrinsic source resistance. The transconductance was increased from 130 to 145 mS/mm by annealing the devices at 250 for 20 minutes in a N2 atmosphere.

For the construction of photonic crystal fiber (PCF) systems using their unique properties, a PCF coupler (PCFC) is one of the key components of the systems. The characteristics of the PCFC depend on the state of air holes in the tapered region of the PCFC because the state of air holes in the tapered region affects light propagation in the PCFC taper. In this paper, coupling characteristics of PCFCs were theoretically investigated. In PCFCs with air hole remaining tapers, we found that a smaller elongation ratio i.e. a stronger elongation is required to obtain optical coupling as an air hole pitch or a ratio of air hole diameter to pitch is larger. In PCFCs with air hole collapsed tapers, it was clarified that a dependence of extinction ratio on air hole collapsed elongation ratio is higher for smaller elongation ratio. It was also clarified that an air hole remaining PCFC has slow wavelength characteristics in extinction ratio compared to an air hole collapsed PCFC. Air hole remaining PCFCs and air hole collapsed PCFCs were fabricated using a CO2 laser irradiation technique. We could successfully control whether air holes in the PCFC taper were remaining or collapsed by adjusting the irradiated laser power in the elongation process of the PCFC fabrication. It was experimentally clarified that the air hole remaining PCFC has slow wavelength characteristics in extinction ratio compared to the air hole collapsed PCFC. The tendencies of the measured wavelength characteristics of PCFCs agree with those of numerical results.

The least-squares linear filtering and fixed-point smoothing problems of uncertainly observed signals are considered when the signal and the observation additive noise are correlated at any sampling time. Recursive algorithms, based on an innovation approach, are proposed without requiring the knowledge of the state-space model generating the signal, but only the autocovariance and crosscovariance functions of the signal and the observation white noise, as well as the probability that the signal exists in the observations.

Route optimization for network mobility is a key technique for providing a node in a mobile network (Mobile Network Node or MNN) with high quality broadband communications. Many schemes adding route optimization function to Network Mobility (NEMO) Basic Support protocol, the standardized network mobility management protocol from the IETF nemo working group, have already been proposed in recent years. One such scheme, a scheme using Hierarchical Mobile IPv6 (HMIPv6) aims to overcome micromobility management issues as well by applying a mechanism based on HMIPv6. The traditional scheme, however, suffers from a significant number of signaling messages as the number of MNNs and/or the number of their Correspondent Nodes (CNs) increase, because many messages notifying the MNNs' Home Agents (HAMNNs) and the CNs of the mobile network's movement are generated simultaneously each time the mobile network moves to the domain of another micromobility management router (Mobility Anchor Point or MAP). This paper proposes a scheme to overcome this problem. Our scheme reduces the number of signaling messages generated at the same time by managing the mobility of MNNs using multiple MAPs distributed within a network for load sharing. The results of simulation experiments show that our scheme works efficiently compared to the traditional scheme when a mobile network has many MNNs and/or these MNNs communicate with many CNs.

Cooperation can increase the system performance by obtaining the spatial diversity. While most of the present works concentrate on the analysis of the cooperation based on the inter-user channel response and developing a scheme for higher cooperative diversity, in this paper, we focus on practical resource allocation in OFDMA systems. Since the user who uses the same center frequency can not receive the signal when transmitting, this constraint should be considered to apply the cooperation to OFDMA systems. In this paper, we propose the pair-based OFDMA frame structure that overcomes this constraint. Also in this frame structure to achieve the minimum outage probability of system, we select the best partner among the candidate neighbors and allocate the suitable subchannels to bandwidth requested users through a cooperative subchannel allocation (CSA) algorithm. In order to evaluate the proposed resource allocation scheme, we carry out simulations based on IEEE 802.16e. The simulation results show that our proposed algorithm offers smaller outage probability than one based on non-cooperative communications and we get the minimum outage probability when a threshold for selection of candidate neighbors is 10 dB. We analyze that these results can be achieved by helping users located around the edge of the cell.

A new adaptive model based on fuzzy integrals has been presented and used for combining three well-known methods, Eigenface, Fisherface and SOMface, for face classification. After training the competence estimation functions, the adaptive mechanism enables our system the filtering of unsure judgments of classifiers for a specific input. Comparison with classical and non-adaptive approaches proves the superiority of this model. Also we examined how these features contribute to the combined result and whether they can together establish a more robust feature.

The concept of personal networks is very user-centric and representative for the next generation networks. However, the present security mechanism does not consider at all what happens whenever a mobile node (device) is compromised, lost or stolen. Of course, a compromised, lost or stolen mobile node (device) is a main factor to leak stored secrets. This kind of leakage of stored secrets remains a great danger in the field of communication security since it can lead to the complete breakdown of the intended security level. In order to solve this problem, we propose a 3-way Leakage-Resilient and Forward-Secure Authenticated Key Exchange (3LRFS-AKE) protocol and its security architecture suitable for personal networks. The 3LRFS-AKE protocol guarantees not only forward secrecy of the shared key between device and its server as well as providing a new additional layer of security against the leakage of stored secrets. The proposed security architecture includes two different types of communications: PN wide communication and communication between P-PANs of two different users. In addition, we give a performance evaluation and numerical results of the delay generated by the proposed security architecture.

Optical Burst Switching (OBS) is one of the most promising switching technologies for next generation optical networks. As delay-sensitive applications such as Voice-over-IP (VoIP) have recently become popular, OBS networks should guarantee stringent Quality of Service (QoS) requirements for such applications. Thus, this paper proposes an Adaptive Loss-aware Flow Control (ALFC) scheme, which adaptively decides on the burst offset time based on loss-rate information delivered from core nodes for assigning a high priority to delay-sensitive application traffic. The proposed ALFC scheme also controls the upper-bounds of the factors inducing delay and jitter for guaranteeing the delay and jitter requirements of delay-sensitive application traffic. Moreover, a piggybacking method used in the proposed scheme accelerates the guarantee of the loss, delay, and jitter requirements because the response time for flow control can be extremely reduced up to a quarter of the Round Trip Time (RTT) on average while minimizing the signaling overhead. Simulation results show that our mechanism can guarantee a 10-3 loss-rate under any traffic load while offering satisfactory levels of delay and jitter for delay-sensitive applications.

This paper proposes a novel MIMO system that introduces a heterogeneous stream (HTS) scheme and a blind signal detection method for mobile radio communications. The HTS scheme utilizes different modulation or coding methods for different MIMO streams, and the blind detection method requires no training sequences for signal separation, detection, and channel estimation. The HTS scheme can remove the ambiguity in identifying separated streams without unique words that are necessary in conventional MIMO blind detection. More specifically, two examples of HTS are considered: modulation type HTS (MHTS) and timing-offset type HTS (THTS). MHTS, which utilizes different modulation constellations with the same bandwidth for different streams, has been previously investigated. This paper proposes THTS which utilizes different transmission timing with the same modulation. THTS can make the blind detection more robust and effective with fractional sampling. The blind joint processing of detection and channel estimation performs adaptive blind MIMO-MLSE and is derived from an adaptive blind MLSE equalizer that employs the recursive channel estimation with the Moore-Penrose generalized inverse. Computer simulations show that the proposed system can achieve superior BER performance with Eb/N0 degradation of 1 dB in THTS and 2.5 dB in MHTS compared with the ideal maximum likelihood detection.