The single path routing protocol, known as the Ad Hoc On-demand Distance Vector, has been widely studied for use in mobile ad hoc networks. AODV requires a new route discovery whenever a path breaks. Such frequent route discoveries cause a delay due to route discovery latency. To avoid such inefficiency, a multipath routing protocol has been proposed that attempts to find link-disjoint paths in a route discovery. However, when there are two or more common intermediate nodes on the path, the protocol can not find a pair of link-disjoint paths even if the paths actually exist. To reduce this route discovery latency, it is necessary to increase the opportunities for finding a pair of link-disjoint paths. In this paper, we focus on AODV and propose an AODV-based new multipath routing protocol for mobile ad hoc networks. The proposed routing protocol uses a new method to find a pair of link-disjoint paths by selecting a route having a small number of common intermediate nodes on its path. Using simulation models, we evaluate the proposed routing protocol and compare it with AODV and the existing multipath routing protocol. Results show that the proposed routing protocol achieves better performance in terms of delay than other protocols because it increases the number of cases where a pair of link-disjoint paths can be established.

Analytical derivation of bit error rates for multi-user coherent chaos-shift-keying (CSK) communication systems are presented in this paper. Nearly exact results are obtained by applying the central limit theorem of statistics to sums of independent variables. Based on χ2 distribution approximations, more viable but still very accurate results decrease complexity of the calculations. The χ2 approach is compared with the widely used Gaussian approximation approach to show its superiority in most cases. Bit error performance bounds for the multi-user CSK system from the approach are deduced as further contributions of this paper. The theoretical results obtained are entirely consistent with a range of simulations.

In this study, a CG animation tool was designed that allows interpolation and extrapolation of two types of repeated motions including finger actions, for quantitative analyses of the relationship between features of human motions and subjective impressions. Three-dimensional human motions are measured with a magnetic motion capture and a pair of data gloves, and then relatively accurate time-series joint data are generated utilizing statistical characteristics. Based on the data thus obtained, time-series angular data of each joint for two dancing motions is transformed into frequency domain by Fourier transform, and spectral shape of each dancing action is interpolated. The interpolation and extrapolation of two motions can be synthesized with simple manner by changing an weight parameter while keeping good harmony of actions. Using this CG animation tool as a motion synthesizer, repeated human motions such as a dancing action that gives particular impressions on the observers can be quantitatively measured and analyzed by the synthesis of actions.

In this paper, we propose a fixed monocular camera, which changes the focus cyclically to recognize completely the three-dimensional translational motion of a rigid object. The images captured in a half cycle of the focus change form a multi-focus image sequence. The motion in depth or the focus change of the camera causes defocused blur. We develop an in-focus frame tracking operator in order to automatically detect the in-focus frame in a multi-focus image sequence of a moving object. The in-focus frame gives a 3D position in the motion of the object at the time that the frame was captured. The reconstruction of the motion of an object is performed by utilizing non-uniform sampling theory for the 3D position samples, of which information were inferred from the in-focus frames in the multi-focus image sequences.

The AODV (Ad Hoc On-Demand Distance Vector) protocol is one of the typical reactive routing protocols in Ad Hoc networks, in that mobile nodes initiate routing activities only in the presence of data packets in need of a route. In this paper, we focus upon the local repair mechanism of AODV. When a link is broken, the upstream node of the broken link repairs the route to the destination by initiating a local route discovery process. The process involves the flooding of AODV control messages in every node within a radius of the length from the initiating node to the destination. In this paper, we propose an efficient local repair scheme for AODV, called AELR (AODV-based Efficient Local Repair). AELR utilizes the existing routing information in the downstream intermediate nodes which have been on the active route to the destination before a link break occurs. AELR can reduce the flooding range of AODV control messages and the route recovery time for route recovery because it can repair a route through the nearby downstream intermediate nodes. The performance results show that AELR can achieve faster route recovery than the local repair mechanism of AODV.

We propose an efficient IP address assignment protocol in mobile ad hoc networks, which use a proactive routing protocol. In this method, which is termed the Bisected-Range based Assignment (BRA), a node repeatedly broadcasts an Agent Request to ask for address assignment. If there are one or more neighbor MANET nodes, one of them becomes an agent to select and assign an IP address to the requesting node. We use address location in the IP address space so that each agent maintains its own exclusive address range to be used for address selection, resulting to decrease the possibility of address conflict. If the requesting node cannot discover any neighbor MANET node over pre-determined random agent-search time, it selects by itself an IP address at random from the given address block. We evaluate performance of the basic and enhanced BRAs by computer simulation. It is shown that the basic and enhanced BRAs can reduce address conflict compared with random assignment. It is also shown that the enhanced BRA is superior in terms of control traffic overhead as well as address assignment delay over the random assignment with the strong Duplicate Address Detection.

Novel high-frequency asymptotic solutions for the scattered fields by a dielectric circular cylinder with a radius of curvature sufficiently larger than the wavelength are presented in this paper. We shall derive the modified UTD (uniform Geometrical Theory of Diffraction) solution, which is applicable in the transition regions near the geometrical boundaries produced by the incident ray on the dielectric cylinder from the tangential direction. Also derived are the uniform geometrical ray solutions applicable near the geometrical boundaries and near the caustics produced by the ray family reflected on the internal concave boundary of the dielectric cylinder. The validity and the utility of the uniform solutions are confirmed by comparing with the exact solution obtained from the eigenfuction expansion.

In this paper, the magnetic field properties around household appliances are investigated with the single coil model and equivalent source model, which are used as main source models in the European standard EN50366 (CENELEC). The accuracy of the field properties is conducted for the coil model (defined in the EN50366), by comparing with the results of the equivalent source model, which allow the reproduction of the complicated inhomogeneous magnetic field around the appliance with full generality (i.e. supports three dimensional vector fields).

This paper analyzes program and erase mechanisms for Floating Channel type Surrounding Gate Transistor (FC-SGT) Flash memory cells for the first time. In FC-SGT Flash memory cell, control gate, floating gate, drain and source is arranged vertically on the substrate. The body region is isolated from the substrate by the bottom source region. The cell is programmed by applying a high positive voltage to the control gate electrode with drain and source electrodes grounded. Erasing is performed by applying a high positive voltage to the drain and source electrodes with the control gate electrode grounded. The physical models for program and erase operations in FC-SGT Flash memory cell are developed. Program and erase operations based on the developed physical models are simulated by utilizing a device simulator. Program and erase characteristics obtained from the device simulation agree well with the results of analytical models. The FC-SGT Flash memory cell can realize program and erase operation with a floating body structure.

Point-to-point optical and millimeter wave communication has recently been of interest, especially in urban areas. Its benefits include simpler and easier installation compared with a land-based line. However, this technology suffers when adverse weather conditions are present, such as rain, fog and clouds, which induce scattering and absorption of the optical wave. The effects of scattering and absorption degrade the quality of the communication link resulting in increase of bit-error-rate. Therefore, there exists a need for accurate channel characterization in order to understand and mitigate the problem. In this paper, radiative transfer theory is employed to study the behavior of amplitude modulated signal propagating through a random medium. We show the effect of the medium to a modulated signal and relate the outcome on the quality of the communication link.

For future high-speed wireless communications using orthogonal frequency division multiplexing (OFDM), two major system requirements will emerge: throughput improvement and rich interference elimination. Because of its broadband nature and limited frequency allocations worldwide, interference from co-located wireless LAN's operating in the same frequency band will become a serious deployment issue. Adaptive array antenna can enhance the performance by suppressing the co-channel interference even when interference may have a large amount of multipath and also have similar received power to the desired signal. There are typically two types of adaptive array architecture for OFDM systems, whose signal processing is carried out before or after FFT (Fast Fourier Transform). In general, the pre-FFT array processing has low complexity, but in rich multipath and interference environments, the performance will deteriorate drastically. In contrast, the post-FFT array processing can provide the optimum performance even in such severe environments at the cost of complexity. Therefore, complexity-reduction techniques combined with the achievement of high system performance will be a key issue for adaptive array antenna applications. This paper proposes novel adaptive array architecture, which is a complexity-reduction technique using subcarrier clustering for post-FFT adaptive array. In the proposed scheme, plural subcarriers can be clustered into a group with the same spatial weight. Simulation results show that the proposed architecture is a promising candidate for real implementation, since it can achieve high performance with much lower complexity even in a rich multipath environment with low signal to noise plus interference ratio (SNIR).

High frequency (HF) diffraction is known as local phenomena, and only parts of the scatterer contribute to the field such as the edge, corner and specular reflection point etc. Many HF diffraction techniques such as Geometrical Theory of Diffraction (GTD), Uniform Theory of Diffraction (UTD) and Physical Theory of Diffraction (PTD) utilize these assumptions explicitly. Physical Optics (PO), on the other hand, expresses the diffraction in terms of radiation integral or the sum total of contributions from all the illuminated parts of scatterers, while the PO currents are locally defined at the point of integration. This paper presents PO-based visualization of the scattering and diffraction phenomena and tries to provide the intuitive understanding of local property of HF diffraction as well as the relations between PO and the ray techniques such as GTD, UTD etc. A weighting named "eye function" is introduced in PO radiation integrals to take into account of local cancellation between rapidly oscillating contributions from adjacent currents; this extracts important areas of current distribution, whose location moves not only with the source but also with the observation point. PO visualization illustrates both local property of HF scattering and defects associated with ray techniques. Furthermore, careful examination of visualized image reminds us of the error factor in PO as applied for curved surfaces, named fictitious penetrating rays. They have been scarcely recognized if not for visualization, though they disturb the geometrical shadow behind the opaque scatterer and can be the leading error factors of PO in shadow regions. Finally, visualization is extended to slot antennas with finite ground planes by hybrid use of modified edge representation (MER) to assess the significance of edge diffraction.

Superluminal group velocity in dispersive media has long been controversial. A partial source of confusion seems to be the absence of high precision numerical results concerning the waveform of the transmitted signal. This paper gives the precise waveforms of a causal half-sine-modulated pulse and a triangle-modulated pulse propagating in the Lorentz medium. Thus, the effects of analyticity of signal are clarified, which the analysis using Gaussian pulse cannot. Further, to deepen understanding of the mechanism of superluminal group velocity, we give a network theoretic consideration.

In this paper, we present the interlaced fast Fourier transform (FFT) method to parallelize the adaptive integral method (AIM) algorithm for the radar cross-section (RCS) computation of large scattering objects in free space. It is noted that the function obtained after convolution is smoother as compared to the original functions. Utilizing this concept, it is possible to interlace the grid current and charge sources in AIM and compute the potentials on each set of interlaced grid independently using FFT. Since the potentials on each interlaced grid are smooth functions in space, we can then interpolate the potentials to every other nodes on the original grid. The final solution of the potentials on the original grid is obtained by summing the total contributions of all the computed and interpolated potentials from every individual interlaced grid. Since the potentials of each interlaced grid can be computed independently without much communication overheads between the processes, such an algorithm is suitable for parallelizing the AIM solver to run on distributed parallel computer clusters. It is shown that the overall computation complexity of the newly proposed interlaced FFT scheme is still of O(N log N).

Integrated implementation of RF front-end components has been shown to posses many benefits. Furthermore, it presents a new way of approaching RF design. This paper will discuss the recent developments by the author's group in the field of RF front-end technology. This will include stand-alone RF front-end components such as a self-heterodyne mixer as well as more functional front-end circuitry such as digital beamformer arrays, retrodirective arrays and an array error calibration scheme.

We present mutually pulse-coupled two relaxation oscillators having refractoriness. The system can be implemented by a simple electrical circuit, and various periodic synchronization phenomena can be observed experimentally. The phenomena are characterized by a ratio of phase locking. Using a return map having a trapping window, the ratio can be analyzed in a parameter subspace rigorously. We then clarify effects of the refractoriness on the pulse coding ability of the system.

This paper presents a new approach based on current mode circuits for fast and accurate optical level monitoring with wide dynamic range of a gigabit burst-mode laser driver chip. Our proposed solution overcomes the drawbacks that voltage mode implementations show at higher bit rates or in other technologies. The main speed-limiting factor of the level monitoring circuitry is the parasitic capacitance of the back facet monitor photodiode. We propose the use of an active-input current mirror to reduce the impact of this parasitic capacitance. The mirror produces two copies of the photo current, one to be used for the "0" level measurement and another for the "1" level measurement. The mirrored currents are compared to two reference currents by two current comparators. Every reference current needs only one calibration at room temperature. A pattern detection block scans the incoming data for patterns of sufficiently long consecutive 0's or 1's. At the end of such a pattern a valid measurement is present at the output of one of the current comparators. Based on these measurements the digital Automatic Power Control (APC) will adjust the bias (IBIAS) and modulation current (IMOD) setting of the laser driver. Tests show that the chip can stabilize and track the launched optical power with a tolerance of less than 1 dB. In these tests the pattern detection was programmed to sample the current comparators after 5 bytes (32 ns at 1.25 Gbps) of consecutive 1's and 0's. Automatic power control on such short strings of data has not been demonstrated before. Although this laser transmitter was developed for FSAN GPON applications at a speed of 1.25 Gbps upstream, the design concept is generic and can be applied for developing a wide range of burst mode laser transmitters. This chip was developed in a 0.35 µm SiGe BiCMOS process.

In this paper we consider an approximation method of a formal linearization which transform time-varying nonlinear systems into time-varying linear ones and its applications. This linearization is a kind of a coordinate transformation by introducing a linearizing function which consists of the Chebyshev polynomials. The nonlinear time-varying systems are approximately transformed into linear time-varying systems with respect to this linearizing functions using Chebyshev expansion to the state variable and Laguerre expansion to the time variable. As applications, nonlinear observer and filter are synthesized for time-varying nonlinear systems. Numerical experiments are included to demonstrate the validity of the linearization. The results show that the accuracy of the approximation by the linearization improves as the order of the Chebyshev and Laguerre polynomials increases.

A novel parallel acceleration technique is proposed based on intrinsic parallelism characteristics of shooting-and-bouncing ray launching (SBR) algorithm, which has been implemented using the MPI parallel library on common PC cluster instead of dedicated parallel machines. The results reveal that the new technique achieves very large speedup gains and could be the efficient and low-cost propagation prediction solution.

Orthogonal Frequency Division Multiplexing (OFDM) is a promising technique for achieving high bit-rate transmission in radio environments. Various techniques to estimate channel attenuation have been proposed for OFDM transmission. In these techniques, the added pilot semi-blind (APSB) channel estimation has been proposed, which does not require any additional bandwidth. For an OFDM packet transmission that includes preambles, it is difficult to track the channel variation of the latter of packet due to time-varying channels in fast fading environments. We expect that the channel estimation is improved by applying the APSB channel estimation technique to the last symbols of packets without any additional bandwidth or degradation of bit rate. In this paper, we propose an OFDM packet transmission system with APSB channel estimation technique where this technique is applied to the last symbols of packets. We expect that the proposed system can track the fast time-variant channels without decrease of the data-rate, and the packet error rate (PER) is improved. We show that our proposed system is effective for improving the accuracy of the channel estimate in fast fading channels.