Metallic pair lines transmitting high-frequency information signals above several tens MHz are often used without being twisted, as flat floor cable installed in buildings, ribbon-type cables installed in computer equipment, and traces in printed circuit boards. However, the conversion characteristics of untwisted unbalanced metallic pair lines connecting unbalanced circuits have not been investigated over a wide range of frequencies in the MHz region. First, we developed a method to estimate effective power conversion factors using a cascade connection of F matrices, where the unbalance in impedance and admittance of each pair line is distributed uniformly along the line. As a result some useful information was obtained about the balance-unbalance conversion characteristics of the effective power which can be used to suppress EMI phenomena in wiring, especially over several decades of high frequencies. Next, we attempted to apply the conversion characteristics of untwisted unbalanced pair lines obtained at frequencies below several MHz to techniques for searching for the return circuits of conductors installed in buildings. It was clarified experimentaly that the depth of the equivalent ground plane can be estimated by comparing the measured conversion values of TV feeder lines installed at the place being tested with reference values measured in advance on a copper plate .

For common-mode noise current reduction, a CMC (Common Mode Choke) is widely used in signal transmission line circuits consisting of a ground and two conductors (a balanced transmission line). However, a common-mode noise current reduction characteristic is not clearly analyzed yet in the case that a CMC is inserted in a balanced transmission line. In this paper we propose the calculation method of CMC insertion losses and derive an equation to analyze the common-mode current characteristics of a balanced transmission line with a CMC inserted. The analyzed frequency range is from 100 kHz to 100 MHz. We conclude that in the frequency range up to 30 MHz: (1) the proposed insertion loss calculation method is useful for analyzing CMC insertion losses in differential-mode and in common-mode; (2) the derived circuit equation can be applied for analyzing the common-mode current characteristics of a balanced transmission line locally unbalanced with conditions of a CMC inserted; (3) the proposed calculation method may give the expected results that a CMC should be placed in a signal source side of an unbalanced point of a pair-cable for reduction of common-mode currents; and (4) if it is placed in a terminal (or load) side of an unbalanced point, there is no effect, or rather common-mode currents are increased by the insertion of a CMC.

A design method for transmission apparatus lightning surge protection has not yet been clarified, because study on lightning surge inducing mechanism has been neglected. This paper analyzes the lightning surges induced on overhead lines by the return strokes, when ground conductivity is finite. The lightning surges induced on overhead lines are calculated by considering the vertical electric field and horizontal electric field created by the return stroke. Calculated values agree well with measured values. Lightning surgre dependency on the distance between strike point and cable, on cable length, on ground conductivity, on cable terminal earth resistance and on cable height above ground are clarified. The probability distribution for peak values, front time and time to half values of the lightning surge waves are obtained both theoretically and experimentally. As a result, data on a standard lightning surge wave form, which is expressed by peak value, front time and time to half value, may be obtained from the relation between the blown fuse rate and the lightning surge occurrence rate.

The thin coated fiber design against lateral force is discussed and a 0.5 mm diameter Polyetherimido coated optical fiber which has equivalent optical loss increase properties against lateral force to conventional 0.9 mm diameter Nylon coated optical fibers is proposed. The method of calculating critical lateral force which causes loss increase is shown. Using the result, it is possible to design coated optical fibers having no loss increase at a given lateral force.

This paper proposed the advantages of using a 2D/3D hybrid imagery system over the use of 3D by itself. A hybrid imagery system was created by projecting a 3D (stereo) image in between and overlapping onto two adjacent 2D images. The negative effect where 2D and 3D images overlap was studied and resolved. Then sensations subject experienced from the visual cues under the different conditions were attained. Participant's sensations while looking at the different forms of imagery on both a flat screen and a flat/inclined screen combination were then attained. The data for the 2D/3D hybrid system were compared with that attained for a 3D image system on its own (without 2D images). Results indicate that there are benefits to using a 2D/3D hybrid system over 3D by itself.