In the letter we extend our previous work, which applies genetic programming to passive filter synthesis tasks. The extended method deals with the tolerance design considerations. Experimental results show that our method can effectively generate filters which outperform those generated by traditional methods. In addition, it provides filter designers with an effective CAD tool to manage the trade-off between manufacturing yield and circuit cost.

This paper proposes a genetic programming method to synthesize passive filter circuits. This method allows both the circuit topology and the component values to be evolved simultaneously. Experiments show that this method is fast and capable of generating circuits which are more economical than those generated by traditional design approaches. In addition, we take into account practical design considerations at high-frequency applications, where the component values are frequency-dependent and restricted to some discrete values. Experimental results show that our method can effectively generate not only compliant but also economical circuits for practical design tasks.

Novel dual-band bandpass filter (BPF) with quasi-elliptic function response by using the meander coupled step-impedance resonators (SIRs) is presented. By tuning the appropriate impedance ratio (K) and physical length of SIRs, the BPF has good dual-band performance at 2.4 and 5.2 GHz with high selectivity, due to the transmission zeros appeared in two passband edges. Measured results of the proposed BPF have a good agreement with the electromagnetic (EM) simulated results.

This paper proposes a parallel coupled microstrip bandpass filter (BPF) with ring Electromagnetic Bandgap (EBG) cells on the middle layer for spurious suppression. The ring EBG cells of the middle layer add a good stopband-rejection mode to the second harmonics of the parallel coupled microstrip BPF with suppression of over -50 dB, without affecting the center frequency and insertion loss of the original designed BPF. The design of ring EBG cells is presented and verified by the experimented results.

In this paper, an inverse S-shaped slotted ground structure (S-SGS) is proposed and analyzed. The S-SGS generates dual attenuation poles that can be easily controlled by its structure parameters. The equivalent circuit of the S-SGS consists of lumped elements that can be extracted from the measured S parameters. Moreover, several S-SGS cells are applied to form a miniaturized lowpass filter (LPF), which has a smaller area and a wider stopband in comparison to previous works.

In this paper, a compact ultra-wideband bandpass filter (UWB-BPF) using pseudo-interdigital stepped-impedance resonators (PIDT-SIRs) is designed and implemented on a commercial printed circuit board (PCB) of RT/Duroid 5880 substrate. The first two resonant modes of the SIR are coupled together and they are applied to create a wide passband. The proposed filter at center frequency f0 of 7.1 GHz has very good measured characteristics including the bandwidth of 3.68-10.46 GHz (3-dB fractional bandwidth of 95%), low insertion loss of -0.50.4 dB, sharp rejection due to two transmission zeros in the passband edge created by the inter-stage coupling. Experimental results of the fabricated filter show a good agreement with the predicted results.

This investigation proposes a modified equivalent circuit of single complementary split-ring resonator (CSRR) in planar transmission media and a dual-mode ring bandpass filter (BPF) that uses periodic CSRRs to suppress the spurious response. The proposed modified equivalent circuit consists of lumped elements that can be easily extracted from the measured S parameters. The proposed dual-mode ring BPF has exhibits a wide stopband characteristic owing to the bandgap resonant characteristic of CSRRs in the harmonic frequency of the dual-mode ring BPF. Good agreement with EM simulation and measurement is demonstrated.

In this letter, the fabrication of a compact and high performance semi-lumped coplanar waveguide low-pass filter (CPW-LPF) on high resistivity silicon (HRS) substrate at millimeter wave is proposed. The design procedure and the equivalent circuit of the proposed semi-lumped CPW-LPF is discussed. The filter structure of is very simple but its performances is fairly good. This designed filter at cutoff frequency fc of 31 GHz has very good measured characteristics including the low insertion loss, sharp rejection and low group delay, due to the reduced substrate loss of HRS. Experimental results of the fabricated filter show a good agreement with the predicted results.