The simulation of a specific absorption rate (SAR) with a temperature distribution becomes more important in the treatment planning for microwave hyperthermia. The simulation technique can also be used to estimate SAR distribution inside human body under hazardous electromagnetic (EM) field circumstances. In the simulation, to use exact permittivity of biological tissues becomes very important to obtain accurate SAR distribution. The permittivity of the medium is very sensitive to the temperature. Therefore, it is considered that the SAR distribution is also very sensitive to the tissue temperature. In this paper, SAR distribution is calculated using FDTD method considering tissue temperature under the electromagnetic (EM) field irradiation. Simulations of temperature distribution are also performed using heat transfer equation. In addition, temperature depending blood flow is taking into account to obtain temperature depending SAR distribution. The results can be used to estimate temperature depending heat generation which can be applied such as microwave hyperthermia treatment.

To measure temperature dependent complex permittivity of dielectric materials, a rectangular cavity resonator with a heating system has been developed. In the experiment, microwave power with the frequency of 2.45 GHz is applied to heat the dielectric material. In order to reduce the error of the complex permittivity of dielectric material obtained from the perturbation method, an electromagnetic (EM) field simulator is applied which uses the Transmission Line Modeling (TLM) method. The uniformity of the temperature is also discussed by the use of heat transfer equation which applies the results of TLM simulation. It is found from the results that the accurate temperature dependence of complex permittivity of the material can be obtained by the method presented here.

Development of non-invasive techniques to measure blood sugar level is strongly required. The application of millimeter waves has a great potentiality to realize the measuring technique. Nevertheless, the practical method of the technique is not yet reported. In this paper, a new technique is proposed to measure blood sugar level using millimeter waves. The technique proposed here is very rapid and safety way to obtain blood sugar level.

A conventional waveguide filter is usually composed of a waveguide which is set with irises and posts inside. When dielectric material is not loaded inside the filter, the filter is too large to mount it on a planar circuit even if the frequency band is as high as the millimeter-wave band. In this paper, we propose a dielectric waveguide filter using LTCC (Low-Temperature Co-fired Ceramics) which can be mounted on a planar circuit. The dielectric waveguide filter using LTCC is composed of a dielectric-loaded waveguide including posts (via holes) and TEM-TE10 converters. The design method of the filter is shown and comparison of the simulated and the experimental results in the 6 GHz band is demonstrated. The simulated results agreed well with the experimental ones. To improve the attenuation characteristics, particularly at the above pass-band frequencies, an attenuation pole is added using a cross patch set inside the LTCC filter in the 25 GHz band. The effect of the cross patch is confirmed using the same simulation method as used for the 6 GHz band. As a result, it is confirmed that the cross patch is very useful for improving the attenuation characteristics at the above pass-band frequencies.

A partially ferrites and dielectric loaded water filled waveguide applicator is presented which can be used for microwave heating of tissues. The applicator can change its heating pattern by changing the external DC magnetic field applied to the ferrites. The electromagnetic (EM) field distribution inside the applicator is obtained theoretically and the simulated EM field inside the applicator is checked experimentally using 430MHz. Furthermore, on the basis of the EM field distribution inside the applicator, simulations of SAR distribution inside lossy homogeneous human tissue as muscle are performed using finite difference time domain (FD-TD) method. Simulated data of Specific Absorption Rate (SAR) distribution is compared with the experimental ones. Simulations of temperature distribution are also performed using heat transfer equation. Simulated data of temperature elevation distribution is compared with the experimental ones. The simulated results agree well with the experimental ones and it is confirmed that the heating pattern can be changed by external DC magnetic field applied to the applicator. The results obtained here show that the partially ferrites and dielectric loaded water filled waveguide applicator which operates at 430 MHz can change its heating pattern without changing its setup and can heat local target on the human body for hyperthermia treatment.

The body area network (BAN) has attracted attention because of its potential for high-grade wireless communication technology and its safety and high durability. Also, human area transmission of a BAN propagating at an ultra-wide band (UWB) has been demonstrated recently. When considering the efficiency of electromagnetic (EM) propagation inside the human body for BAN and hyperthermia treatment using RF, it is important to determine the mechanism of EM dissipation in the human body. A body heating system for hyperthermia must deposit EM energy deep inside the body. Also, it is important that the EM field generated by the implant system is sufficiently strong. In this study, the specific absorption rate (SAR) distribution is simulated using an EM simulator to consider the biological transmission mechanism and its effects. To utilize the EM field distribution using an implant system for hyperthermia treatment, the SAR distribution inside the human body is simulated. As a result, the SAR distribution is concentrated on the surface of human tissue, the muscle-bolus interface, the pancreas, the stomach, the spleen and the regions around bones. It can also be concentrated in bone marrow and cartilage. From these results, the appropriate location for the implant system is revealed on the basis of the current distribution and differences in the wave impedance of interfacing tissues. The possibility of accurate data transmission and suitable treatment planning is confirmed.

A light, thin and flexible applicator using a microstrip patch array for microwave heating is presented and tested in this work. The applicator is made of a flat silicone rubber bag, inside of which flows cooling water. EM coupling feeding is applied, which has no direct contact between the feed and the patch, to improve durability and reliability when it is repeatedly applied to the uneven surface of the heated portion of the human body. Simulations of SAR distribution are performed using the finite difference time domain (FD-TD) method. Simulated data are compared with the experimental ones using cubic and cylindrical phantom models with single and multielement patch applicators. Simulations of temperature distribution are also performed using the heat transfer equation. Simulated data are compared with the experimental ones using cubic and cylindrical phantom models. The simulated results agree well with the experimental ones. The results obtained here show that the multielement flexible microstrip patch applicator which operates at 430MHz can heat a relatively shallow and widespread area on the human body for hyperthermia treatments.

A semicylindrical microstrip applicator system is proposed and designed, both for microwave heating and for noninvasive temperature estimation, in application to hyperthermia treatment. The experimental results showed that the system functions both as a heating device and as a means of noninvasive temperature estimation. Therefore, electrical switching of these two functions makes the system realize both heating and temperature estimation. These functions reduce the pain of hyperthermia therapy for patients. The system is constructed of a water-loaded cylindrical applicator. Thus, the whole system can be made compact compared to conventional applicators. This improvement allows for various merits, such as realizing a surface cooling effect and decreased leakage of electromagnetic (EM) waves. When the applicator is set as an array arrangement, the system can be used as a microwave heating device. The penetration depth can be varied by adjusting phases of the EM wave radiated from each applicator. The experimental results at 430 MHz showed that semicylindrical microstrip applicators can be expected to be valid for tumor heating at depths within 55 mm. Moreover, by measuring transmission power between the two applicators, the system can be used to estimate temperature inside the medium. The transmission power which was measured in the frequency domain was converted in the time domain. By such a method, temperature distribution was calculated by solving simple simultaneous primary equations. The results of the temperature estimation show that the number of estimated temperature segments which have an error within 0.5 is 28 out of 36. The system can be easily used as a temperature measuring applicator as well as a heating applicator.

A dielectric rod waveguide applicator for microwave heating such as microwave hyperthermia is described. The applicator consists of the acrylic cylinder filled with deionized water. By circulating the deionized water, the dielectric rod waveguide applicator acts as a surface cooling device, so that it doesn't need any bolus. This surface cooling device enables the dielectric rod waveguide applicator to control the site of effective heating region along the depth axis. Useful pattern of the circular or spheroidal shape and axially symmetric effective heating region were obtained. Furthermore metal strips provided on the aperture of applicator control the shape of the heating pattern.

A new applicator using a multi-microstrip antenna for hyperthermia is proposed and developed. The applicator consists of semi-cylindrical microstrip elements which serve as non-invasive heating and temperature estimation inside the body. Major advantage of the applicator is that heating and temperature estimation are achieved through only simple switching; The array applicator can heat deep region with surface cooling. Meanwhile the applicator detects an appreciable change in the transmission coefficient of electric field.