The search functionality is under construction.
The search functionality is under construction.

Keyword Search Result

[Keyword] ZCS(3hit)

1-3hit
  • Implementation of Soft Switching Forward Converter with Self-Driven Synchronous Rectification

    Majid DELSHAD  Nasrin ASADI MADISEH  Bahador FANI  Mahmood AZARI  

     
    PAPER-Electronic Circuits

      Vol:
    E98-C No:10
      Page(s):
    963-970

    In this paper, a new single soft switched forward converter with a self driven synchronous rectification (SDSR) is introduced. In the proposed converter, a soft switching condition (ZCS turn on and ZVS turn off) is provided for the switch, by an auxiliary circuit without any extra switch. In additional, this auxiliary circuit does not impose high voltage or current stresses on the converter. Since the proposed converter uses SDSR to reduce conductive loss of output rectifier, the rectifier switches are switched under soft switching condition. So, the conductive and switching losses on the converter reduce considerably. Also, implementing control circuit of this converter is very simple, due to the self-driven method employed in driving synchronous rectification and the converter is controlled by pulse width modulation (PWM). The experimental results of the proposed converter are presented to confirm the theoretical analysis.

  • Analysis of a Multi-Oscillated Current Resonant Type DC-DC Converter

    Osamu MATSUO  Hirofumi MATSUO  Yoichi ISHIZUKA  Hiroyuki OTA  

     
    PAPER-Energy in Electronics Communications

      Vol:
    E91-B No:10
      Page(s):
    3307-3312

    This paper presents the analysis of a new multi-oscillated current resonant type DC-DC converter. Current resonant converters have several remarkable features such as high efficiency, small size, low cost and low noise, and are frequently employed in many portable electronic systems such as personal computers, cellular phones and flat panel displays. The current resonant type converter generally employs pulse frequency modulation for constant voltage control in the output. For this reason, the magnetizing current through the converter not only causes a power loss under a light load, but also a loss during stand-by. Therefore, this type of converter has a problem in that the required smaller size cannot be achieved, because an auxiliary source is necessary for stand-by. In order to solve these problems, a new current resonant type power supply is proposed in which two driving methods are employed. In these driving methods, one MOSFET as a main switch is driven by an auxiliary winding of the transformer and another MOSFET as a main switch is driven by the driving IC with a low withstand voltage. Good agreement of the observed and simulated waveforms was confirmed. In addition, eight distinct states and four distinct operating modes, which compose of the sequence of states, were clarified by experimental and simulated analysis.

  • High-Frequency Isolated Soft-Switching Phase-Shift PWM DC-DC Power Converter Using Tapped Inductor Filter

    Sergey MOISEEV  Koji SOSHIN  Mutsuo NAKAOKA  

     
    PAPER-DC/DC Converters

      Vol:
    E87-B No:12
      Page(s):
    3561-3567

    In this paper, a novel type of the step-up high frequency transformer linked full-bridge soft-switching phase-shift PWM DC-DC power converter with ZVS and ZCS bridge legs is proposed for small scale fuel cell power generation systems, automotive AC power supplies. A tapped inductor filter with a freewheeling diode is implemented in the proposed soft-switching DC-DC power converter to minimize the circulating current in the high-frequency step-up transformer primary side and high-frequency inverter stage. Using a tapped inductor filter with a freewheeling diode makes possible to reduce the circulating current without any active switches and theirs gate-drive circuits. The operating principle of the proposed DC-DC power converter with each operation mode during a half cycle of the steady state operation is explained. The optimum design of the tapped inductor turns ratio is described on the basis of the circuit simulation results. Developing 1 kW 100 kHz prototype with power MOSFETs and 36 V DC source verifies the practical effectiveness of the proposed soft-switching DC-DC power converter. The actual efficiency of the proposed DC-DC power converter is obtained 94% for the wide load and output voltage variation ranges.