We propose and demonstrate a new fabrication process of a microchannel using the Damascene process. This process aims to integrate photonic circuits with microchannels fabricated in a glass film. The microchannel is fabricated by the removal of the sacrificial layer after a sacrificial layer is formed by the Damascene process and the cover is formed by sputter deposition. A thin cover layer can be formed by the sacrificial method, because the cover layer is supported by the sacrificial layer during film formation. The cover layer is hermetically sealed, since it is formed by radio frequency (RF) sputtering deposition. The thickness is 1 µm and the width ranges from 3.5 to 8 µm. Using the proposed microchannel fabrication method, we prepared a microelectromechanical system (MEMS) optical switch using microfluidics, and we confirmed its functional operation. This optical switch actuates a minute droplet of liquid injected into the microchannel using Maxwell's stresses. Light propagates straight through the waveguide so that the light passes through the microchannel when the droplet is in the microchannel, but the light rays are completely reflected into a crossed waveguide when the droplet is not in the microchannel. Since this fabrication method uses techniques common to those in the formation of copper wiring in an IC chip, it can be used in the microchannel process.
The copyright of the original papers published on this site belongs to IEICE. Unauthorized use of the original or translated papers is prohibited. See IEICE Provisions on Copyright for details.
Copy
Takuji IKEMOTO, Yasuo KOKUBUN, "Fabrication of Microchannel with Thin Cover Layer for an Optical Waveguide MEMS Switch Based on Microfluidics" in IEICE TRANSACTIONS on Electronics,
vol. E90-C, no. 1, pp. 78-86, January 2007, doi: 10.1093/ietele/e90-c.1.78.
Abstract: We propose and demonstrate a new fabrication process of a microchannel using the Damascene process. This process aims to integrate photonic circuits with microchannels fabricated in a glass film. The microchannel is fabricated by the removal of the sacrificial layer after a sacrificial layer is formed by the Damascene process and the cover is formed by sputter deposition. A thin cover layer can be formed by the sacrificial method, because the cover layer is supported by the sacrificial layer during film formation. The cover layer is hermetically sealed, since it is formed by radio frequency (RF) sputtering deposition. The thickness is 1 µm and the width ranges from 3.5 to 8 µm. Using the proposed microchannel fabrication method, we prepared a microelectromechanical system (MEMS) optical switch using microfluidics, and we confirmed its functional operation. This optical switch actuates a minute droplet of liquid injected into the microchannel using Maxwell's stresses. Light propagates straight through the waveguide so that the light passes through the microchannel when the droplet is in the microchannel, but the light rays are completely reflected into a crossed waveguide when the droplet is not in the microchannel. Since this fabrication method uses techniques common to those in the formation of copper wiring in an IC chip, it can be used in the microchannel process.
URL: https://global.ieice.org/en_transactions/electronics/10.1093/ietele/e90-c.1.78/_p
Copy
@ARTICLE{e90-c_1_78,
author={Takuji IKEMOTO, Yasuo KOKUBUN, },
journal={IEICE TRANSACTIONS on Electronics},
title={Fabrication of Microchannel with Thin Cover Layer for an Optical Waveguide MEMS Switch Based on Microfluidics},
year={2007},
volume={E90-C},
number={1},
pages={78-86},
abstract={We propose and demonstrate a new fabrication process of a microchannel using the Damascene process. This process aims to integrate photonic circuits with microchannels fabricated in a glass film. The microchannel is fabricated by the removal of the sacrificial layer after a sacrificial layer is formed by the Damascene process and the cover is formed by sputter deposition. A thin cover layer can be formed by the sacrificial method, because the cover layer is supported by the sacrificial layer during film formation. The cover layer is hermetically sealed, since it is formed by radio frequency (RF) sputtering deposition. The thickness is 1 µm and the width ranges from 3.5 to 8 µm. Using the proposed microchannel fabrication method, we prepared a microelectromechanical system (MEMS) optical switch using microfluidics, and we confirmed its functional operation. This optical switch actuates a minute droplet of liquid injected into the microchannel using Maxwell's stresses. Light propagates straight through the waveguide so that the light passes through the microchannel when the droplet is in the microchannel, but the light rays are completely reflected into a crossed waveguide when the droplet is not in the microchannel. Since this fabrication method uses techniques common to those in the formation of copper wiring in an IC chip, it can be used in the microchannel process.},
keywords={},
doi={10.1093/ietele/e90-c.1.78},
ISSN={1745-1353},
month={January},}
Copy
TY - JOUR
TI - Fabrication of Microchannel with Thin Cover Layer for an Optical Waveguide MEMS Switch Based on Microfluidics
T2 - IEICE TRANSACTIONS on Electronics
SP - 78
EP - 86
AU - Takuji IKEMOTO
AU - Yasuo KOKUBUN
PY - 2007
DO - 10.1093/ietele/e90-c.1.78
JO - IEICE TRANSACTIONS on Electronics
SN - 1745-1353
VL - E90-C
IS - 1
JA - IEICE TRANSACTIONS on Electronics
Y1 - January 2007
AB - We propose and demonstrate a new fabrication process of a microchannel using the Damascene process. This process aims to integrate photonic circuits with microchannels fabricated in a glass film. The microchannel is fabricated by the removal of the sacrificial layer after a sacrificial layer is formed by the Damascene process and the cover is formed by sputter deposition. A thin cover layer can be formed by the sacrificial method, because the cover layer is supported by the sacrificial layer during film formation. The cover layer is hermetically sealed, since it is formed by radio frequency (RF) sputtering deposition. The thickness is 1 µm and the width ranges from 3.5 to 8 µm. Using the proposed microchannel fabrication method, we prepared a microelectromechanical system (MEMS) optical switch using microfluidics, and we confirmed its functional operation. This optical switch actuates a minute droplet of liquid injected into the microchannel using Maxwell's stresses. Light propagates straight through the waveguide so that the light passes through the microchannel when the droplet is in the microchannel, but the light rays are completely reflected into a crossed waveguide when the droplet is not in the microchannel. Since this fabrication method uses techniques common to those in the formation of copper wiring in an IC chip, it can be used in the microchannel process.
ER -