Power analysis for IoT devices is strongly required to protect attacks from malicious attackers. It is also very important to reduce power consumption itself of IoT devices. In this paper, we propose a highly-adaptable and small-sized in-field power analyzer for low-power IoT devices. The proposed power analyzer has the following advantages: (A) The proposed power analyzer realizes signal-averaging noise reduction with synchronization signal lines and thus it can reduce wide frequency range of noises; (B) The proposed power analyzer partitions a long-term power analysis process into several analysis segments and measures voltages and currents of each analysis segment by using small amount of data memories. By combining these analysis segments, we can obtain long-term analysis results; (C) The proposed power analyzer has two amplifiers that amplify current signals adaptively depending on their magnitude. Hence maximum readable current can be increased with keeping minimum readable current small enough. Since all of (A), (B) and (C) do not require complicated mechanisms nor circuits, the proposed power analyzer is implemented on just a 2.5cm×3.3cm board, which is the smallest size among the other existing power analyzers for IoT devices. We have measured power and energy consumption of the AES encryption process on the IoT device and demonstrated that the proposed power analyzer has only up to 1.17% measurement errors compared to a high-precision oscilloscope.

This paper describes the effects of system LSI design with C language-based behavioral synthesis following several trials of design period reduction and quality improvement for a variety of circuit types. The results of these trials are analyzed from the viewpoints of description productivity, verification productivity, reusability and design flexibility as well as hardware and software co-verification. First the C-based design flow proposed by the authors is described, and the design productivity and verification productivity under this design flow is compared to RTL design. The reusability of the behavioral IP core and its efficiency with HW/SW co-verification are also shown using design examples. Next, using the example of an MPEG-4 video decoder design, a typical design process in a C-based design is shown with considerations regarding verification efficiency, reusability of the IP core and HW/SW co-verification. Finally, the authors' perspectives regarding future directions of system LSI design are discussed.

Scattering of a three-dimensional Hermite-Gaussian beam mode by a dielectric circular cylinder at normal incidence is considered by using the complex-source-point method. The scattered fields are examined numerically for a lowest-order mode.

This letter discusses the quality improvement of reconstructed images in diffraction tomography. An efficient iterative procedure based on the modified Newton-Kantorovich method and the Gerchberg-Papoulis algorithm is presented. The simulated results demonstrate the property of high-quality reconstruction even for cases where the first-order Born approximation fails.

An efficient reconstruction algorithm for diffraction tomography based on the modified Newton-Kantorovich method is presented and numerically studies. With the Fréchet derivative obtained for the Helmholtz equation, one can derive an iterative formula for getting an object function, which is a function of refractive index of a scatterer. Setting an initial guess of the object function to zero, the pth estimate of the function is obtained by performing the inverse Fourier transform of its spectrum. Since the spectrum is bandlimited within a low-frequency band, the algorithm does not require usual regularization techniques to circumvent ill-posedness of the problem. For numerical calculation of the direct scattering problem, the moment method and the FFT-CG method are utilized. Computer simulations are made for lossless and homogeneous dielectric circular cylinders of various radii and refractive indices. In the iteration process of image reconstruction, the imaginary part of the object function is set to zero with a priori knowledge of the lossless scatterer. Then the convergence behavior of the algorithm remarkably gets improved. From the simulated results, it is seen that the algorithm provides high-quality reconstructed images even for cases where the first-order Born approximation breaks down. Furthermore, the results demonstrate fast convergence properties of the iterative procedure. In particular, we can successfully reconstruct the cylinder of radius 1 wavelength and refractive index that differs by 10% from the surrounding medium. The proposed algorithm is also effective for an object of larger radius.

Financial exchanges provide market data feeds to update their members about changes in the market. Feed messages are often used in time-critical automated trading applications, and two identical feeds (A and B feeds) are provided in order to reduce message loss. A key challenge is to support A/B line arbitration efficiently to compensate for missing packets, while offering flexibility for various operational modes such as prioritising for low latency or for high data reliability. This paper presents a reconfigurable acceleration approach for A/B arbitration operating at the network level, capable of supporting any messaging protocol. Two modes of operation are provided simultaneously: one prioritising low latency, and one prioritising high reliability with three dynamically configurable windowing methods. We also present a model for message feed processing latencies that is useful for evaluating scalability in future applications. We outline a new low latency, high throughput architecture and demonstrate a cycle-accurate testing framework to measure the actual latency of packets within the FPGA. We implement and compare the performance of the NASDAQ TotalView-ITCH, OPRA and ARCA market data feed protocols using a Xilinx Virtex-6 FPGA. For high reliability messages we achieve latencies of 42ns for TotalView-ITCH and 36.75ns for OPRA and ARCA. 6ns and 5.25ns are obtained for low latency messages. The most resource intensive protocol, TotalView-ITCH, is also implemented in a Xilinx Virtex-5 FPGA within a network interface card; it is used to validate our approach with real market data. We offer latencies 10 times lower than an FPGA-based commercial design and 4.1 times lower than the hardware-accelerated IBM PowerEN processor, with throughputs more than double the required 10Gbps line rate.

Scheduling, an essential step in high-level synthesis, is an intractable process. Traditional heuristic scheduling methods usually search schedules directly in the entire solution space. In this paper, we propose the idea of searching within an intermediate solution space (ISS). We put forward a max-flow scheduling method that heuristically prunes the solution space into a specific ISS and finds the optimum of ISS in polynomial time. The proposed scheduling algorithm has some unique features, such as the correction of previous scheduling decisions in a later stage, the simultaneous scheduling of all the operations, and the optimization of more complicated objectives. Aided by the max-flow scheduling method, we implement the optimization of the IC power-ground integrity problem at the behavior level conveniently. Experiments on well-known benchmarks show that without requiring additional resources or prolonging schedule latency, the proposed scheduling method can find a schedule that draws current more stably from a supply, which mitigates the voltage fluctuation in the on-chip power distribution network.

A novel inverse scattering approach is developed to the reconstruction of electrical property distributions of a two-dimensional biaxial anisotropic object using time-domain scattering data. The approach is an extension of the forward-backward time-stepping (FBTS) algorithm previously described for an isotropic object. Synthetic examples of inversion are given to assess the effectiveness of the proposed method.