1-6hit |
Hiroki WAKATSUCHI Stephen GREEDY John PAUL Christos CHRISTOPOULOS
This paper demonstrates an efficient modelling method for artificial materials using digital filtering (DF) techniques. To demonstrate the efficiency of the DF technique it is applied to an electromagnetic bandgap (EBG) structure and a capacitively-loaded loop the so-called, CLL-based metamaterial. Firstly, this paper describes fine mesh simulations, in which a very small cell size (0.10.10.1 mm3) is used to model the details of an element of the structures to calculate the scattering parameters. Secondly, the scattering parameters are approximated with Padé forms and then factorised. Finally the factorised Padé forms are converted from the frequency domain to the time domain. As a result, the initial features in the fine meshes are effectively embedded into a numerical simulation with the DF boundary, in which the use of a coarse mesh is feasible (1,000 times larger in the EBG structure simulation and 680 times larger in the metamaterial simulation in terms of the volumes). By employing the coarse mesh and removal of the dielectric material calculations, the heavy computational burden required for the fine mesh simulations is mitigated and a fast, efficient and accurate modelling method for the artificial materials is achieved. In the case of the EBG structure the calculation time is reduced from 3 hours to less than 1 minute. In addition, this paper describes an antenna simulation as a specific application example of the DF techniques in electromagnetic compatibility field. In this simulation, an electric field radiated from a dipole antenna is enhanced by the DF boundary which models an artificial magnetic conductor derived from the CLL-based metamaterial. As is shown in the antenna simulation, the DF techniques model efficiently and accurately large-scale configurations.
In the paper, we introduce TLM methodology focusing on IEEE 802.11 WLAN as a derivative system. Decomposing the entire system into several computation components, we analyzed the property of each transaction, resulting in the TLM. In the case of shared bus, the simulation results show the effect of communication architecture such as bus protocol and bus parameters on the system performance.
Byungsoo KIM Kyesuk JUN Ihn Seok KIM
In this paper, the absorbing property of the discrete Green's function ABC, which was based on a powerful concept of the TLM method, has been improved by relocating loss process from the time domain to the space domain. The proposed scheme simply adds a loss matrix to the connection matrix in the basic TLM algorithm to make the formulation of the ABC more efficient. Various lengths of absorbing layers discretized for a WR-90 empty waveguide have been tested in terms of reflection property. An expression for an optimum absorbing property has been also derived with respect to the length of the layer. Comparison of the layer with the discrete Green's function ABC shows that the layer in this study has improved reflection property better than approximately 3 and 6 dB, respectively, when 50Δ
Hiroaki KOGURE Hideki NAKANO Kohji KOSHIJI Eimei SHU
This paper presents a method of analyzing the electromagnetic field inside an equipment housing. The electromagnetic field is assumed to be coming from outside and coupled into the housing through an aperture on the housing surface. The analysis is based on the transmission-line modeling method. Results of the analysis show a good agreement with the results of measurement. Also, it is found that the coupling through the aperture shows peaks at some frequencies that depend almost only on the structure of the housing and aperture and, therefore, can be estimated at the time of equipment design.
This paper describes the method of applying the integral form of Maxwell's equations to the transmission-line network used in the spatial network method for the modeling of curved conductor surfaces. The techniques of dealing with the transmission-line network near cylindrical conductor surface are explained in detail. To compare exact solutions with computed values, a cylindrical cavity resonator is analysed. The resonant frequencies and unloaded Q's for the computed three modes are obtained with the error of about 1%. Moreover, applying this treatment to the waveguide with magnetron anodeshape cross section, a cutoff-constant is computed successfully. It is found that the treatment proposed in this paper can be used as the method for modeling of curved conductor surface in the spatial network method. It is also considered that this treatment can be extend to TLM method.
Yoshiyuki FUJINO Cheuk-yu Edward TONG
To increase the accuracy of a near field antenna measurement system, it is necessary to know radiation characteristics of a probe to detect near field data. Open ended waveguide used as a near field probe in our system was analyzed using Transmission Line Matrix (TLM) method which is a time domain electromagnetic solver. Validity of this analysis has been confirmed by comparison with experimental data and existing theoretical approximation. Frequency dependence of a complex reflection coefficient at the waveguide aperture has been derived and is shown to agree with measured values. The radiation pattern of the open ended waveguide with mounting structure is also calculated. Ripples on both the amplitude and phase patterns are correctly predicted by our simulation. This method can be applied to accurately model the effect of probe antennas to enhance the accuracy of near field antenna range.