This letter presents a simple joint estimation method for residual frequency offset (RFO) and sampling frequency offset (STO) in OFDM-based digital video broadcasting (DVB) systems. The proposed method selects a continual pilot (CP) subset from an unsymmetrically and non-uniformly distributed CP set to obtain an unbiased estimator. Simulation results show that the proposed method using a properly selected CP subset is unbiased and performs robustly.

In multi-input multi-output orthogonal frequency division multiplexing (MIMO-OFDM) systems, phase tracking schemes suffer from co-channel interference (CCI) and inter-carrier interference (ICI) caused by residual frequency offset. In this paper, we propose a residual frequency offset compensation scheme using feedback phase tracking to eliminate the effect of both ICI and CCI for MIMO-OFDM systems. The proposed phase tracking scheme estimates the amount of residual frequency offset in the frequency domain, and compensates for it in the time domain, periodically. Thus, the effect of ICI can be reduced. Furthermore, we consider two methods of channel estimation that enable the system to estimate the channel response several times within a packet to eliminate the effect of CCI. This is because the channel is generally estimated at the beginning of a packet, and this estimation is affected by residual frequency offset. First is the method that employs midambles. Second is the one that reuses the preamble. When the channel is estimated several times within a packet, the effect of CCI can be reduced. Simulation results show the proposed scheme can compensate for residual frequency offset and CCI more accurately than the conventional scheme, and improve the packet error rate (PER) performance.

In orthogonal frequency-division multiplexing (OFDM)-based wireless local area networks (WLANs), phase noise (PHN) and residual frequency offset (RFO) can cause the common phase error (CPE) and the inter-carrier interferences (ICI), which seriously degrade the performance of systems. In this letter, we propose a combined pilot symbol assisted and decision-directed channel estimation scheme based on the least-squares (LS) and the maximum-likelihood (ML) algorithms. Simulation results present that the proposed scheme significantly improves the performance of OFDM-based WLANs.

This letter evaluates the performance of an uplink multicarrier-code division multiple access (MC-CDMA) system when the frequency offsets of all users are random variables and the frequency offset for the desired user is compensated. The analysis confirms that performance degradation due to frequency offset is negligible if the estimation error of normalized frequency offset for the desired user is less than 10-1.

An antenna with a wide bandwidth is required for ultra-wideband (UWB) system of the future. Several types of wideband antenna that cover the whole frequency range have been proposed. Since the UWB system would cover from 3.1 to 10.6 GHz, it is necessary to suppress the interference from other systems using some of this frequency band. This paper presents two types of novel planar monopole antenna: one consists of two connected rectangular plates and another one is an orthogonal type. The return loss characteristics, radiation pattern, and current distribution of these antennas were simulated by using the FDTD method. The proposed antennas had dual frequency and broad bandwidth characteristics at both resonant frequencies. The return loss level at the eliminated frequency between the resonant frequencies was almost 0 dB. The radiation patterns for the whole frequency range were almost omni-directional in the horizontal plane. The current distributions at each frequency were similar to that of a planar rectangular monopole. The radiation patterns thus were omni-directional in the horizontal plane at each resonant frequency. Therefore, the results showed that wide bandwidth characteristics could be achieved with such antennas.

A novel dual-band internal antenna similar in size to the single-band internal antenna for cellular handsets is proposed. Our approach to realize a small and low-profile dual-band internal antenna is to use the dominant mode (TM10 mode) and the higher-order mode (TM30 mode). In order to use this approach for recent dual-band cellular systems it is necessary to lower the resonant frequency of the higher-order mode (TM30 mode). This motivated our development of a new antenna configuration with a slot on the radiation element of a quarter-wavelength shorted microstrip antenna to lower the resonant frequency of the TM30 mode. In this paper, the experimental and the analytical results for this antenna are presented. In the results, by adjusting the location and the length of the slot, the dual-frequency operation can be achieved with the frequency ratio (TM30 mode/TM10 mode) from 2 to 3. In addition, the enhancement of bandwidth is presented.

This paper proposes a newly developed dual-frequency antenna for 800 MHz and 1500 MHz band use. A uniformly spaced array configuration, originally designed for a 800 MHz analog system, is extended to yield dual frequencies operations. An important characteristic of a base station antenna is low sidelobe level in order to suppress inter-cell interference. In the case of a uniformly spaced array configuration, sidelobe levels are increased by the emergence of grating lobes at higher frequencies. Electrical beam tilt also degrades the sidelobe level. As does the change in the excitation coefficients of the array elements at higher frequencies. These three factors are studied theoretically to yield practical sidelobe levels. One more important beam characteristic is the sector beam in the horizontal plane. The same beam width in two frequency bands is achieved by designing the novel reflector shape and determining the proper array element positions in front of the reflector. Practical antenna characteristics are confirmed by designing, manufacturing, and testing a base station antenna.

It is well known that the existence of electrically resistive film layers formed on contact surfaces increases contact resistance and it causes a nonlinear relationship between voltage and current observed in a contact layer. Nonlinear distortion voltages can be detected by our sensitive detection system based on the dual frequency method when a thin film exists on the surface. In this study, multilayer films of polyimide (PI) was used as an ideal material of ultra thin film, because of electrically good insulator with simple molecular structure, to study non-linearity through metal-insulator-metal contact. The number of deposited layers between one and twenty one were formed on three types of substrates; (a) evaporated gold on a glass plate, (b) gold plate and (c) evaporated gold on gold plate, to obtain good insulating film. Where each layer of PI film has 0. 4 nanometer thickness. A pin contact was made by pressing a bent gold wire on the PI film. It is concluded that [1]; the second-order distortion voltage increases exponentially as the film thickness increases, [2]; polarity of the surface potential of PI depends on the film thickness, and that I-V characteristic depends on the polarity of the surface potential.