Smartphones for wireless communication typically consist of a large area frontal liquid crystal display (LCD), which incorporates a metal back plate, and a back cover chassis made from metal. Leveraging this structure a new approach to construct antennas for smartphones is proposed where the complete metal back cover chassis and LCD back plate are used as the radiating element and ground plane. In the design a feedline is connected between the metal back cover chassis and LCD back plate, along with shorts at various locations between the two metal plates, to control the resonance frequency of the resulting antenna. Multiple-band operation is possible without the need for any slots in the plates for radiation. Results show that antenna frequency reconfigurability can be achieved when switching function is added to the shorts so that several wireless communication bands can be covered. This approach is different from existing metallic frame antenna designs currently available in the market. A design example is provided which uses one PIN diode for the switching shorts and the target frequency bands are 740-780MHz and 900-1000MHz & 1700-1900MHz. The optimization of LC matchings and concerns of hand effects and metallic components between the chassis and LCD metal back plate are also addressed.

In this paper, a simple pattern reconfigurable antenna with broadband circular polarization is proposed. The proposed antenna consists of four rectangular loops, a feeding network and four reflectors. Circular polarization is achieved by cutting two slots on opposite sides of the loops. By controlling the states of the four PIN diodes present in the feeding network, the proposed antenna can achieve four different pattern modes at the same frequency. Experiments show that the antenna has a bandwidth of 47.6% covering 1.73-2.81GHz for reflection coefficient (|S11|)<-10dB and a bandwidth of 55% covering 1.62-2.85GHz for axial ratio <3dB. The average gain is 8.5dBi and the radiation patterns are stable.

We propose a new configuration for phased array antennas. The proposal uses radiation pattern reconfigurable antennas as the antenna element to improve the gain on the scanning angle and to suppress the grating lobes of sparse phased array antennas. This configuration can reduce the element number because the desired gain of the total array can be achieved by using fewer elements. We demonstrate the concept by designing a radiation pattern reconfigurable Yagi-Uda antenna. PIN diode switches are added to the parasitic elements to change director and reflector. The switches of multiple array elements are concurrently controlled by just a single one-pair line. This control structure is simple and can be applied to large-scale arrays. The proposed antenna yields an element gain that almost matches the theoretical limit across about half the coverage, even if the element spacing is enlarged to 1λ. If the switch states are interchanged, the gain in the mirror direction can be increased. We design a 48-element array and compare its gain against those of normal dipole antennas. We also fabricate the proposed antenna and demonstrate radiation pattern switching.

A frequency-reconfigurable dipole antenna, whose dual resonant frequencies are independently controlled, is introduced. The antenna's conductor consists of radiating conductors, lumped and distributed elements, and varactors. To design the antenna, current distribution, input impedance, and radiation power including higher-order modes, are analyzed for a narrow-angle sectorial antenna embedded with passive elements. To derive the formulae used, radiation power is analyzed in two ways: using Chu's equivalent circuit and the multipole expansion method. Numerical estimations of electrically small antennas show that dual-band antennas are feasible. The dual resonant frequencies are controlled with the embedded series and shunt inductors. A dual-band antenna is fabricated, and measured input impedances agree well with the calculated data. With the configuration, an electrically small 2.5-/5-GHz dual-band reconfig-urable antenna is designed and fabricated, where the reactance values for the series and shunt inductors are controlled with varactors, each connected in series to the inductors. Varying the voltages applied to the varactors varies the measured upper and lower resonant frequencies between 2.6 and 2.9GHz and between 5.1 and 5.3GHz, where the other resonant frequency is kept almost identical. Measured radiation patterns on the H-plane are almost omni-directional for both bands.

This paper presents a pattern reconfigurable Yagi-Uda antenna on an FR-4 printed circuit board (PCB) for 2.435-2.465GHz-frequency short-range radiocommunication devices. To realize the antenna, pin diodes are attached onto the antenna's driven elements and parasitic elements. The direction of the beam is shifted by alternating the pin diodes status between ON and OFF to induce a quad-directional operation so that E-plane maximum beams are formed in the directions of 135°, 45°, 310° and 225° (i.e. regions 1, 2, 3, 4), respectively. A series of simulations are performed on four parameters: microstrip-to-CPS (coplanar stripline), inter-parasitic spacing, parasitic length, and modes of parasitic elements (i.e. director/reflector) to determine the optimal antenna design. A prototype is fabricated based on the optimal simulation results. The experiments showed very good agreement between the simulation and measured results with regard to the reflection coefficients, radiation patterns and gains for all four beams.

In this paper, compact reconfigurable wideband Inverted-F Antenna (IFA) elements are proposed for a Long Term Evolution (LTE) mobile terminal. The proposed inverted-F antenna has a very simple planar arrangement. A capacitive coupling feed strip is employed to modify the input impedance matching. A chip inductor is connected in series to the feeding point to realize the wideband property. The whole Multiple-Input Multiple-Output (MIMO) antenna system consists of two similar inverted-F antenna elements. Antenna element #1 has a wideband property with a 6-dB bandwidth from 0.74 to 0.9GHz. To further expand the bandwidth, antenna element #2 has a reconfigurable property through the use of a Positive Intrinsic-Negative (PIN) diode. Antenna element #2 has a 6-dB bandwidth from 0.74 to 0.84GHz when the PIN diode is on and from 0.79 to 0.9GHz when the PIN diode is off. Moreover, the proposed MIMO antenna has a low radiation-pattern-based envelope correlation coefficient (ECC), which is less than 0.15 over LTE bands 4, 5, 13, and 14.

This paper presents a new technique to enhance the bandwidth of a printed dipole antenna for ultra-wideband applications. The basic idea is to exploit mutual coupling between the feeding line, which is designed closed and paralleled to dipole arms, the dipole arms and other elements of the antenna. Dipole arms, feeding lines as well as other parts are investigated in order to expand antenna bandwidth while still retaining antenna compactness. Based on the proposed technique, we develop two sample printed dipole antennas for advanced wireless communications. One is an ultra-wideband antenna which is suitable for multi-band-mode ultra-wideband applications or being a sensing antenna in cognitive radio. The other is a reconfigurable antenna which would be applicable for wideband cognitive radios. Antenna characteristics such as radiation patterns, current distributions, and gains at different frequencies are also investigated for both sample antennas.

In this letter a circular polarization microstrip antenna with switchable polarization is proposed. The switchable polarization sense characteristic is realized via a shunt connected varactor tuning diode. The appropriate capacitance of the diode at the reverse bias voltage can alter two circular polarizations, as the tuning diode, which is located near the rectangular slot in the circular patch, is utilized in a perturbation element. The switchable polarization is analyzed using the equivalent circuit model representing the resonances of each orthogonal mode. Simulation, calculated, and measured results agree well.

A feed-point-selective, asymmetrically fed dipole antenna has been proposed for multiple-input multiple-output (MIMO) applications. By using PIN diode switches, an asymmetrical antenna feed is realized so as to control antenna directivities. The two basic requirements for MIMO antenna radiation patterns, namely, a decrease in overlap and control in direction, have been achieved. Additionally, to enhance directivities for the antenna with PIN diodes, a reflector has been introduced. The gain toward the reflector decreased by 2 dB, while the gain in the direction of the maximum gain increased by 2 dB. The developed antenna can correspond to a variable power angular spectrum (PAS).

This letter presents a reconfigurable antenna with a microstrip patch that uses PIN-diode connections on slits to achieve frequency diversity. By switching the diodes on or off, a surface current path on the antenna is changed, which effectively results in shifting the operating frequency. Thus the antenna can select both WiBro and DMB bands.

A software antenna, which will be a key device realizing flexible and highly reliable wireless communications systems, is inherently matched with software defined radios (SDR). In this paper, first, key technologies on the software antenna are introduced. The technologies contain i) how to recognize the radio environment, ii) how to determine the optimum adaptive signal processing algorithm, and iii) how to reconfigure the digital beamforming circuit. Then, an image of a software antenna with reconfigurable eigenvector-beamspace configuration is presented. Finally, by assuming various propagation conditions, performance of the software antenna in terms of algorithm diversity is demonstrated.