In terms of the transmission-line theory, a general synthesis of a new class of optimum Chebyshev-type ultra-wideband bandpass (UWB) filter prototype composed of multistage stepped-impedance resonators (SIRs) and two short-circuited shunt stubs positioned at input- and output- ports is presented. By the comparison of the real and theoretical transfer functions, the design/characteristic equations are obtained for the design of the proposed filter prototype rather than the traditional design tables. The explicit expressions of one-stage and two-stage filters are then derived and reported. Accordingly, bandpass filters with an arbitrary FBW (Fractional Bandwidth) and passband ripple can be easily designed by solving the design equations. As an example, a 10-degree Chebyshev distributed filter (two-stage filter) with an FBW of 110% is synthesized to meet FCC's outdoor mask. The synthesized circuit model are confirmed by a commercial circuit simulator and then optimized by an EM simulator, fabricated in microstrip line and characterized by the network analyzer. The good agreements between the measured and predicted frequency responses validate the effectiveness of newly proposed filter prototype and the corresponding synthesis technique. In addition, the designed filter exhibits good characteristics of comparatively low insertion loss, quite sharp skirt, very flat group delay and good stopband (especially in lower one) as well. It should be also highlighted that, compared with the conventional filters composed merely of parallel-coupled SIRs or shunt short-circuit-stubs, the new prototype can reduce the overall length of the filter by more than 3/4λg. Moreover, in terms of the presented design technique, the proposed filter prototype can be also used to easily realize the UWB filters with an FBW even greater than 110%.

The design of microstrip bandpass filters using stepped-impedance resonators (SIRs) is examined. The passband center frequency for the WCDMA-FDD (uplink band) Japanese cellular system is 1950 MHz with a 60-MHz bandwidth. The SIR physical characteristic can be designed using a SIR characteristic chart based on second harmonic suppression. In our filter design, passband design charts were obtained through the design procedure. Tchebycheff and maximally flat bandpass filters of any bandwidth and any number of steps can be designed using these passband design charts. In addition, sharp skirt characteristics in the passband can be realized by having two transmission zeros at both adjacent frequency bands by using open-ended quarter-wavelength stubs at input and output ports. A new even-mode harmonics suppression technique is proposed to enable a wide rejection band having a high suppression level. The unloaded quality factor of the resonator used in the proposed filters is greater than 240.

To realize the compact ultra-wideband (UWB) bandpass filters, a novel filter prototype with two short-circuited stubs loaded at both sides of a stepped-impedance resonator (SIR) via the parallel coupled lines is proposed based on a distributed filter synthesis theory. The equivalent circuit of this filter is established, while the corresponding 7-pole Chebyshev-type transfer function is derived for filter synthesis. Then, a distributed-circuit-based technique was presented to synthesize the elements' values of this filter. As an example, a FCC UWB filter with the fractional bandwidth (FWB) @ -10 dB up to 110% was designed using the proposed prototype and then re-modeled by commercial microwave circuit simulator to verify the correctness and accuracy of the synthesis theory. Furthermore, in terms of EM simulator, the filter was further-optimized and experimentally-realized by using microstrip line. Good agreements between the measurement results and theoretical ones validate the effectiveness of our technique. In addition, compared with the conventional SIR-type UWB filter without short-circuited stubs, the new one significantly improves the selectivity and out-of-band characteristics (especially in lower one -45 dB@1-2 GHz) to satisfy the FCC's spectrum mask. The designed filter also exhibits very compact size, quite low insertion loss, steep skirts, flat group delay and the easily-fabricatable structure (the coupling gap dimension in this filter is 0.15 mm) as well. Moreover, it should be noted that, in terms of the presented design technique, the proposed filter prototype can be also used to easily realize the UWB filters with other FBW even greater than 110%.

Bandpass filters with broad bandwidth (up to 70%), very wide upper stopband (nearest spurious passband occurs up to five times of passband center frequency (f0)), good stopband rejection performance (better than -30-40 dB in the whole stopband region), and matching with the conventional low cost printed circuit board process with low dielectric constant substrates are proposed in this paper. The proposed filters are designed using parallel-coupled vertically installed planar stepped-impedance resonators (VIPSIRs), which adopt the inherent nature of very tight coupling of VIP coupled line and extremely high impedance of VIP line. The extremely tightly coupled line enables the proposed filters having very wide passband and the extremely high impedance of VIP line leads to extremely large low-to-high impedance ratio that pushes the nearest spurious passband up to 5f0. Both VIP coupled line and VIP high impedance line are analyzed and characterized by the design charts. The design procedures based on the design charts are verified by several experimental examples. The measured results agree very well with the simulated ones.

This paper proposes a new microstrip stepped-impedance resonator (SIR) used for bandpass filters with reduced size and improved stopband characteristics. A comprehensive treatment of both ends of the resonator with loaded triangular and rectangular microstrips is described. The design concept is demonstrated by two filter examples including four-resonator parallel-coupled Chebyshev bandpass and compact four-resonator cross-coupled elliptic-type filters. These filters are not only compact size due to the slow-wave effect, but also have a wider upper stopband resulting from the resonator bandstop characteristic. The filter designs are described in details. The simulated and experimental results are demonstrated and discussed.

In this paper a newly designed internally-coupled asymmetric stepped-impedance resonator (SIR) bandpass filter (BPF) is proposed. The asymmetric SIR structure not only can effectively reduce the circuit size but also can provide two flexibly tunable transmission zeros near the lower and upper passband edges. The first transmission zero is due to the series resonance of the quarter-wavelength open stepped-impedance stub, and the second one is produced by anti-parallel coupling between adjacent SIRs. The proposed BPF was fabricated and simulated using the commercial software HFSS, and agreement between the measured and simulated results was observed. A 0.9-dB insertion loss and a shape factor of 3.6 were achieved in the passband, thus indicating that the proposed filter structure is of practical value.

Novel microstrip dual-band bandpass filters with controllable fractional bandwidths and good in-between isolation are presented and implemented. A half-wavelength stepped-impedance resonator is firstly characterized, aiming at producing the two resonant frequencies at 2.4 and 5.2 GHz. Two types of coupled microstrip lines in the parallel and anti-parallel formats are then investigated in terms of unified equivalent J-inverter network. Extensive results are derived to quantitatively show their distinctive frequency-distributed coupling performances under different coupling lengths. The coupling degrees of these two coupled lines at the two resonances are properly adjusted to achieve the dual-passband response with varied or tunable bandwidths. In addition, the parallel coupled line is modeled to bring out a transmission zero between the two resonances so as to achieve the good in-between isolation. The three two-stage bandpass filters are initially designed to exhibit their dual-band response with changeable dual-band bandwidths. A three-stage dual-band filter is in final optimally designed and its predicted performance is confirmed in experiment.

This paper presents a novel method of designing microstrip line multi-frequencies band filters by applying the SIR (stepped impedance resonators) technology. Utilizing the S-parameter and the ABCD parameters of a two-port network is for the analysis of short-circuited and open-circuited resonators with various combinations of series and shunt sequences. By controlling the impedance ratio of the resonators, both center frequencies of the two passbands then are determined. Moreover, a global synthesis approach is also discussed on miniaturization. A simplified architecture based on bent SIR offers the 50% area reduction of layout. Technology of matching circuit creates higher performance multi-band filter. We adjust impedance and electrical length of transmission line (TL) to compensate multi-band and bending for matches and highly improve the insertion and reflection loss. Simulation and measurement are performed to validate our method and are pretty matched.