For measuring high frequency ultrasonic fields which are often spatially distributed and transient, an array probe with small element sensors is highly required. In this paper, we propose a fiber-optic micro-probe array which is based on wavelength-division-multiplexing technique. The element sensor consists of a micro optical cavity of 100 µm long made at the end of optical fiber. Optical path length of the cavity is changed by the applied acoustic field, and the modulation of output light intensity is monitored at another end of the fiber for the information of the acoustic field. Array of sensor elements and a light source as well as a photo detector are connected together by an optical star coupler. The Fabry-Perot resonance wavelength of each sensor element is designed different one another, and the outputs from the sensors are discriminated by sweeping the wavelength of light source with the use of a tunable semiconductor laser. In this paper, the performance of the micro-probe array is discussed experimentally.

Mechanical prosthetic cardiac valves generate not only the widely recognized audible closing clicks but also ultrasonic closing clicks, as previously reported by us. A personal-computer-based measurement and analysis system with the bandwidth of 625 kHz has been developed to clarify the characteristics of these ultrasonic closing clicks. Fifty cases in total were assessed clinically, including cases with tilting disk valves, bileaflet valves, and flat disk valves. The ultrasonic closing clicks are damped vibrations continuing for about two milliseconds, and their frequency range was confirmed to be from 8 kHz to 625 kHz, while that of the audible click was up to 8 kHz. Although the sensitivity of the sensor decreased by approximately 30 dB at 625 kHz, effective power of the ultrasonic closing click was confirmed at this frequency. Moreover, it was shown that, surprisingly, the signal power at 625 kHz was still at the same level as that at around 100 kHz. Those wide bandwidth signal components exist independent of the type of mechanical valve, but the spectral pattern shows some dependence on the valve type.

The efficiency and reliability of an ultrasonic motor, operating in longitudinal-torsional degenerate-mode, are investigated. It is essential to miniaturize both longitudinal and torsional mode piezoelectric ceramic elements, in order to produce low-cost ultrasonic motors, and to realize a motor with low battery power consumption. The ultrasonic motor is designed with an accurate mechanical equivalent circuit, which can produce high design precision notwithstanding low computation cost. It is important in this design that the resonant frequencies of longitudinal mode and torsional mode coincide with each other under the pertinent rotor pressing force and longitudinal and torsional mode piezoelectric ceramic elements are located in the vibration nodes for the longitudinal mode and the torsional mode, respectively. As a result, the fabricated motor, whose rotor diameter was 12 mm, produced 480 r.p.m. no-load revolution speed, 0.55 kgfcm maximum torque, 50% maximum efficiency, 2.5 W consumed power and a lifetime over 1000 hours with continuous rotation.

An image obtained by ultrasonic medical equipment is poor in quality because of speckle noise, that is caused by the quality of ultrasonic beam and so on. Thus, it is very difficult to detect internal organs or the diseased tissues from a medical ultrasonic image by the processing, which is used only gray-scale of the image. To analyze the ultrasonic image, it is necessary to use not only gray-scale but also appropriate statistical character. In this paper, we suggest a new method to extract regions of internal organs from an ultrasonic image by the discrimination function. The discrimination function is based on gray-scale and statistical characters of the image. This function is determined by using parameters of the multi-dimensional autoregressive model.

A new neural network for locating a source by integrating data from a number of sensors is considered. The network gives a solution for inverse problems using a back-propagation algorithm with the architecture to get the solution in the inter-layer weights in a coded form Three different physical quantities are applied to the network, since the scheme has three independent ports; an input port, a tutorial port and an answer port. Our architecture is useful to estimate z" in the problem whose structure is y=f(x,z) where y is the observed data, x is the sensor position and z is the source location. The network integrates the information obtained from a number of sensors and estimates the location of the source. We apply the network to two problems of location estimation: the localization of the active nerves from their evoked potential waveforms and the localization of objects from their echoes using an active sonar system.

Ultrasonic diffraction image of specimen informs its acoustic structure as X ray diffraction method for analysis of the crystal structure. This ultrasonic diffraction method has a feature that focused ultrasound beam is used and diffraction image is observed on focal plane. When the structure of specimen is perfectly periodic, its diffraction image produces symmetrical respect to origin, but the diffraction image of weak periodic structure such as living tissue has some asymmetricity. In this paper, the principle of ultrasonic diffraction method, and data processing for asymmetrical and scattered diffraction image caused by weak periodic structure are described. The results of diffraction image of plant tissue and animal tissue, and its discussion are also described. This method is expected to be useful in evaluation of acoustic structure such as living tissue and internal tissue of bone.

In clad contacts of bonded dissimilar metals used in relays and switches, the bonding state affects the switching performance of those devices. Examining the bonding state and analyzing the relationship between the bonding state and the causes of malfunction, such as welding of the contact, leads to improvement in reliability of electromechanical devices. In this experiment we examined, with an ultrasonic microscope, the bonding state in riveted clad contacts which had been subjected to load-breaks of in-rush current, and were able to demonstrate the causal relation of the bonding state with malfunctions of the contacts. The use of the ultrasonic microscope made it possible to perform a hitherto difficult detailed analysis of the bonding state of clad contacts. It was also confirmed that this was an extremely effective method for studying the relationship with switching performance.

A new system of measuring the thickness of thin filn or paper using 40 kHz ultrasonic wave in air is described. The thickness of samples measured is smaller by a factor of sevreal hundreds than the wavelength of sound. Experinents with polymer and metal films and paper are described to demonstrate the measurement possibilities.

We have calssified parenchymal echo patterns of cirrhotic liver into four types, according to the size of hypoechoic nodular lesions. Neural network technique has been applied to the characterization of hepatic parenchymal diseases in ultrasonic B-scan texture. We employed a multi-layer feedforward neural network utilizing the back-propagation algorithm. We carried out four kinds of pre-processings for liver parenchymal pattern in the images. We describe the examination of each performance by these pre-processing techniques. We show four results using (1) only magnitudes of FFT pre-processing, (2) both magnitudes and phase angles, (3) data normalized by the maximum value in the dataset, and (4) data normalized by variance of the dataset. Among the 4 pre-processing data treatments studied, the process combining FFT phase angles and magnitudes of FFT is found to be the most efficient.

Reflection mode diffraction tomography is expected to reconstruct a higher resolution image than transmission mode. Its image reconstruction problem, however, in the many cases of practical uses becomes ill-posed one. In this paper, a new reconstruction method of limited angle reflection mode diffraction tomography using maximum entropy method is proposed. Results of simulation showed that the method was able to reconstruct the better quality images than IR method poposed by Kak, et al.

We present a navigation system using ultrasonic sensors for unknown and dynamic indoor environments. To achieve the robustness and flexibility of the mobile robot, we develop a behavior-based system architecture, consisting of multi-layered behaviors. Basic behaviors required for the navigation of a mobile robot, such as, avoiding obstacles, moving towards free space, and following targets, are redundantly developed as agents and combined in a behavior-based system architecture. An extended potential filed method is developed to produce the appropriate velocity and steering commands for the behaviors of the robot. We demonstrate the capabilities of our system through real world experiments in unstructured dynamic office environments using an indoor mobile robot.

This paper describes the endurance of a ceramic hydrophone to measure high acoustic pressures at the focal point of Extracorporeal Shockwave Lithotripter (ESWL).

This letter describes damages of piezoelectric polymer using in hydrophones to measure high acoustic pressures at the focal point of Extracorporeal Shockwave Lithotripter (ESWL).