Automatic modulation classification (AMC) is an important function of radio surveillance systems in order to identify unknown signals. Many previous works on AMC have utilized signal cyclostationarity, particularly spectral correlation density (SCD), but many of them fail to address several implementation issues, such as the assumption of perfect knowledge of the symbol rate. In this paper, we discuss several practical issues, e.g. cyclic frequency mismatch, which may affect the SCD, and propose compensation techniques to overcome those issues. We also propose a novel feature extraction technique from the SCD, which utilizes the SCD of not only the original received signal, but also the squared received signal. A symbol rate estimation technique which complements the feature extraction is also proposed. Finally, the classification performance of the system is evaluated through Monte Carlo simulations using a wide variety of modulated signals, and simulation results show that the proposed technique can estimate the symbol rate and classify modulation with a probability of above 0.9 down to SNRs of 5 dB.

Computing the Eigen Value Decomposition (EVD) of a symmetric matrix is a frequently encountered problem in adaptive (or smart or software) antenna signal processing, for example, super resolution DOA (Direction Of Arrival) estimation algorithms such as MUSIC (MUltiple SIgnal Classification) and ESPRIT (Estimation of Signal Parameters via Rotational Invariance Technique). In this paper the hardware architecture of the fast EVD processor of symmetric correlation matrices for the application of an adaptive antenna technology such as DOA estimation is proposed and the basic idea is also presented. Cyclic Jacobi method is well known for the simplest algorithm and easily implemented but its convergence time is slower than other factorization algorithm like QR-method. But if considering the fast parallel computation of the EVD with a hardware architecture like ASIC (Application Specific Integrated Circuit) or FPGA (Field Programmable Gate Array), the Jacobi method can be a appropriate solution, since it offers a quite higher degree of parallelism and easier implementation than other factorization algorithms. This paper computes the EVD using a Jacobi-type method, where the vector rotations and the angles of the rotations are obtained by CORDIC (COordinate Rotation DIgital Computer). The hardware architecture suitable for ASIC or FPGA with fixed-point arithmetic is presented. Because it consists of only shift and add operations, this hardware friendly feature provides easy and efficient implementation. In this paper, the computational load, the estimate of circuit scale and expected performance are discussed and the validation of fixed-point arithmetic for the practical application to MUSIC DOA estimation is examined.

To use millimeter wave bands in future cellular and outdoor wireless networks, understanding the multipath cluster characteristics such as delay and angular spread for different polarization is very important besides knowing the path loss and other large scale propagation parameters. This paper presents result from analysis of wide-band full polarimetric double directional channel measurement at the millimeter wave band in a typical urban pico-cell environment. Only limited number of multipath clusters with gains ranging from -8dB to -26.8dB below the free space path loss and mainly due to single reflection, double reflection and diffraction, under both line of sight (LOS) and obstructed LOS conditions are seen. The cluster gain and scattering intensity showed strong dependence on polarization. The scattering intensities for ϑ-ϑ polarization were seen to be stronger compared to ϕ-ϕ polarization and on average 6.1dB, 5.6dB and 4.5dB higher for clusters due to single reflection, double reflection and scattering respectively. In each cluster, the paths are highly concentrated in the delay domain with delay spread comparable to the delay resolution of 2.5ns irrespective of polarization. Unlike the scattering intensity, the angular spread of paths in each cluster did not show dependence on polarization. On the base station side, average angular spread in azimuth and in elevation were almost similar with ≤3.3° spread in azimuth and ≤3.2° spread in elevation for ϑ-ϑ polarization. These spreads were slightly smaller than those observed for ϕ-ϕ polarization. On the mobile station side the angular spread in azimuth was much higher compared to the base station side. On average, azimuth angular spread of ≤11.4° and elevation angular spread of ≤5° are observed for ϑ-ϑ polarization. These spreads were slightly larger than in ϕ-ϕ polarization. Knowing these characteristics will be vital for more accurate modeling of the channel, and in system and antenna design.

In this paper, we performed six human movement simulation by a commercial software (Poser7). We performed FDTD simulations for body area network propagation with one transmitter and six receivers. Received amplitudes were calculated for every time frame of 1/30 s interval. We also demonstrated a polarization diversity effectiveness for dynamic wearable body area network propagation.

This paper presents a real-time body motion classification system using the radio channel characteristics of a wearable body area network (BAN). We developed a custom wearable BAN radio channel measurement system by modifying an off-the-shelf ZigBee-based sensor network system, where the link quality indicator (LQI) values of the wireless links between the coordinator and four sensor nodes can be measured. After interpolating and standardizing the raw data samples in a pre-processing stage, the time-domain features are calculated, and the body motion is classified by a decision-tree based random forest machine learning algorithm which is most suitable for real-time processing. The features were carefully chosen to exclude those that exhibit the same tendency based on the mean and variance of the features to avoid overfitting. The measurements demonstrated successful real-time body motion classification and revealed the potential for practical use in various daily-life applications.

Hawkins noise model is modified for HBT application. The non-ideal ideality factor of HBT is included in both dynamic resistance and noise figure equations. Emitter resistance is also included. The extraction method of noise resistance Rn is developed. Based on the method, a simple analytic equation of Rn is derived and experimentally verified. The effects of noise sources on minimum noise figure are analyzed. The dominant noise sources are the shot noises of emitter and collector currents. Generally, when the minimum noise figure is measured at various current levels, there exists an current level at which the slope of minimum noise figure curve is zero. The zero slope current level coincides with the current level at which the noise contribution of the emitter and collector shot noises including the cancellation by correlation of two sources is minimum. Parasitic resistance degrades output noise through the shot noise amplification with a minor effect of the thermal noise of itself.

At present, when using space-time processing techniques with multiple antennas for mobile radio communication, real-time weight adaptation is necessary. Due to the progress of integrated circuit technology, dedicated processor implementation with ASIC or FPGA can be employed to implement various wireless applications. This paper presents a resource and performance evaluation of the QRD-RLS systolic array processor based on fixed-point CORDIC algorithm with FPGA. In this paper, to save hardware resources, we propose the shared architecture of a complex CORDIC processor. The required precision of internal calculation, the circuit area for the number of antenna elements and wordlength, and the processing speed will be evaluated. The resource estimation provides a possible processor configuration with a current FPGA on the market. Computer simulations assuming a fading channel will show a fast convergence property with a finite number of training symbols. The proposed architecture has also been implemented and its operation was verified by beamforming evaluation through a radio propagation experiment.

In radio channel measurements and modeling, directional scanning via highly directive antennas is the most popular method to obtain angular channel characteristics to develop and evaluate advanced wireless systems for high frequency band use. However, it is often insufficient for ray-/cluster-level characterizations because the angular resolution of the measured data is limited by the angular sampling interval over a given scanning angle range and antenna half power beamwidth. This study proposes the sub-grid CLEAN algorithm, a novel technique for high-resolution multipath component (MPC) extraction from the multi-dimensional power image, so called double-directional angular delay power spectrum. This technique can successfully extract the MPCs by using the multi-dimensional power image. Simulation and measurements showed that the proposed technique could extract MPCs for ray-/cluster-level characterizations and channel modeling. Further, applying the proposed method to the data captured at 58.5GHz in an atrium entrance hall environment which is an indoor hotspot access scenario in the fifth generation mobile system, the multipath clusters and corresponding scattering processes were identified.

This letter proposes an automatic IQ imbalance compensation technique for quadrature modulators by means of spectrum measurement of RF signal using a spectrum analyzer. The analyzer feeds back only magnitude information of the frequency spectrum of the signal. To realize IQ imbalance compensation, the conventional method of steepest descent is modified; the descent direction is empirically determined and a variable step-size is introduced for accelerating convergence. The experimental results for a four-channel transmitter operating at 11 GHz are presented for verification.

To improve the outage performance of a wireless body area network (BAN), exploitation of the diversity in the channel obtained by letting different nodes cooperate and relay signals for each other is an attractive solution. We carry out multi-link channel measurements and modeling for all realistic locations of the on-body sensor nodes and for three different motion scenarios in a typical office environment to develop equivalent channel model for simple and practical cooperative transmission schemes. Using the developed model the performance of the transmission schemes are evaluated and compared. Incremental decode and forward relaying is found to be consistently better than the other schemes with gains of up to 16dB at 10% outage probability, and an average gain of more than 5.9dB for any location of the coordinator node. The best location of the coordinator node based on the performance is also determined. Such insights will be very useful in designing BANs.

This letter evaluates a transmitter architecture using harmonic images in D/A conversion for generating RF signals. In generating harmonic images, the problems such as intermodulation distortion of DAC were investigated. We developed an evaluation system with two bandpass filter and a buffer amplifier. It was experimentally found that the RF signal up to around 400 MHz can be generated by a commonly used 14-bit DAC at the sampling rates of around 40 MHz with EVM less than 6.6%. This letter also presents a more feasible transmitter example having an IF stage with harmonic image extraction scheme and a typical RF upconversion stage.

Spectrum sensing, a key technical challenge in cognitive radios (CR) technology, is a technique that enables the spectrum of licensed systems to be accessed without causing undue interference. It is well known that cyclostationarity detectors have great advantages over energy detectors in terms of the robustness to noise uncertainty that significantly degrades the performance as well as the capability to distinguish the signal of interest from the other interferences and noise. The generalized likelihood ratio test (GLRT) is a recognized sensing technique that utilizes the inherent cyclostationarity of the signal and has been intensively studied. However, no comprehensive evaluation on its performance enhancement has been published to date. Moreover high computational complexity is still a significant problem for its realization. This paper proposes a maximum ratio combining multi-cyclic detector which uses multiple cyclic frequencies for performance enhancement with reduced computational complexity. An orthogonal frequency-division multiplexing (OFDM) signal based on the ISDB-T (integrated services digital broadcasting terrestrial), a Japanese digital television broadcasting standard, was used in the evaluation assuming this as a primary system in WRAN (wireless regional area network) applications like IEEE 802.22.

Undersampling (or bandpass sampling) phase modulated signals directly at high frequency band, the harmful effects of the aperture jitter characteristics of ADCs (Analog-to-Digital converters) and sampling clock instability of the system can not be ignored. In communication systems the sampling jitter brings additional phase noise to the constellation pattern besides thermal noise, thus the BER (bit error rate) performance will be degraded. This paper examines the relationship between the input frequency to ADC and the sampling jitter in digital IF (Intermediate Frequency) downconversion receivers with undersampling scheme. This paper presents the measurement results with a real hardware prototype system as well as the computer simulation results with a theoretically modeled IF sampling receiver. We evaluated EVM (Error Vector Magnitude) in various clock jitter configurations with commonly used and reasonable cost ADCs of which sampling rates was 40 MHz. According to the results, the IF input frequencies of QPSK (16 QAM) signals were limited below around 290 (210) MHz for wireless LAN standard, and 730 (450) MHz for W-CDMA standard, respectively, in our best configuration.

The input impedance of an antenna fluctuates because of various usage conditions, which causes a mismatch between an internal circuit and an antenna. An automatic matching system solves this problem, then this paper presents a reconfigurable impedance tuner that has a set of fixed capacitors controlled by switching p-i-n diodes. A fast control algorithm for selecting the appropriate conditions of an impedance tuner is proposed and mounted on FPGA to demonstrate the performance.

DOA (Direction Of Arrival) estimation is a useful technique in various positioning applications including the DOA-based adaptive array antenna system. This paper presents a practical implementation of FPGA (Field Programmable Gate Array) based fast DOA estimator for wireless cellular basestation. This system incorporates spectral unitary MUSIC (MUltiple SIgnal Classification) algorithm, which is one of the representative super resolution DOA estimation techniques. This paper proposes a way of digital signal processor design suitable for FPGA and its real hardware implementation. In this system, all digital signal processing procedures are computed by the only fixed-point operation with finite word-length for fast processing and low power consumption. The performance will be assessed by hardware level simulations and experiments in a radio anechoic chamber.

In order to utilize higher frequency bands above 6GHz, which is an important technical challenge in fifth generation mobile systems, radio propagation channel properties in a large variety of deployment scenarios should be thoroughly investigated. The authors' group has been involved in a fundamental research project aimed at investigating multiple-input-multiple-output (MIMO) transmission performance and propagation channel properties at microwave frequency above 10GHz from 2009 to 2013, and since then they have been conducting measurement and modeling for high frequency bands. This paper aims at providing comprehensive tutorial of a whole procedure of channel modeling; multi-dimensional channel sounding, propagation channel measurement, analysis, and modeling, by introducing the developed MIMO channel sounders at high frequency bands of 11 and 60GHz and presenting some measurement results in a microcell environment at 11GHz. Furthermore, this paper identifies challenges in radio propagation measurements, and discusses current/future channel modeling issues as future works.

This paper presents a $24 imes24$ MIMO channel sounder that has been developed based on a scalable fully parallel MIMO architecture. It can be flexibly configured with 3 sub-transmitters and 3 sub-receivers, each of which consists of 8 RF ports. This flexibility allows the measurement for both purposes of double directional and multi-link MIMO channel measurements. Implementation issues related to the multi-link operation on the fully parallel architecture were successfully solved by appropriate system design and applying several calibration techniques. The performance of the developed system was validated by extensive test experiments. Finally, a multi-link channel measurement example in an indoor environment was presented demonstrating the capability of the proposed system.

Automatic modulation classification (AMC) involves extracting a set of unique features from the received signal. Accuracy and uniqueness of the features along with the appropriate classification algorithm determine the overall performance of AMC systems. Accuracy of any modulation feature is usually limited by the blindness of the signal information such as carrier frequency, symbol rate etc. Most papers do not sufficiently consider these impairments and so do not directly target practical applications. The AMC system proposed herein is trained with probable input signals, and the appropriate decision tree should be chosen to achieve robust classification. Six unique features are used to classify eight analog and digital modulation schemes which are widely used by low frequency mobile emergency radios around the globe. The Proposed algorithm improves the classification performance of AMC especially for the low SNR regime.

In this paper, a novel approach of a human motion classification system in wireless body area network (WBAN) using received radio signal strength was developed. This method enables us to classify human motions in WBAN using only the radio signal strength during communication without additional tools such as an accelerometer. The proposed human motion classification system has a potential to be used for improving communication quality in WBAN as well as recording daily-life activities for self-awareness tool. To construct the classification system, a numerical simulation was used to generate WBAN propagation channel in various motions at frequency band of 403.5MHz and 2.45GHz. In the classification system, a feature vector representing a characteristic of human motions was computed from time-series received signal levels. The proposed human motion classification using the radio signal strength based on WBAN simulation can classify 3-5 human motions with the accuracy rate of 63.8-95.7 percent, and it can classify the human motions regardless of frequency band. In order to confirm that the human motion classification using radio signal strength can be used in practice, the applicability of the classification system was evaluated by WBAN measurement data.

This paper presents a framework of multimode fully digital receiver implementation using direct RF-to-digital conversion. In this architecture the entire band including multiple RF systems is directly converted to digital by a wideband high speed ADC, and the RF systems can be easily switched by only digital signal processing with the minimum analog RF components. The digital RF front-end consists of parallel processing blocks for parallel data streams considering practical ADC's configuration. The RF signals are converted into baseband through digital IF stage and the data rates are made down by two steps of decimation. In this paper, a principle investigation into a dualmode system implementation is presented for simplicity. The circuit resource and the robustness to the spurs (spurious outputs) of an NCO (numerically controlled oscillator) in the proposed design will be presented. The proposed architecture was implemented with an FPGA on the developed prototype system and the operations were also verified.