This paper presents a 120-GHz-band amplifier module with a hermetic sealing structure for a broadband wireless system. The sealing structure for F-band waveguides is a laminate composed of two sealing plates and a spacer. Each sealing plate has a fused glass window and separates inside air from the ambient atmosphere. The design process of the sealing structure is simple and has good simulation fidelity. The hermetic sealing structure designed for an amplifier in a 120-GHz-band wireless link has an insertion loss of less than 1dB and a return loss of more than 15dB in the operating band. We made three kinds of sealed modules to evaluate the sealing function. The modules sealed with this technique meet the hermetic-seal standard in MIL-STD-883F. We then verified that the sealing structure on the sealed modules has a small enough effect for the transmittance of the intrinsic characteristics. In addition, we performed 10-Gbit/s data transmission using a sealed amplifier module with the bit error rate of less than 10-10.

This paper proposes cell-attached frame encapsulation schemes in which encapsulation processing can be performed without cell reassembly. The proposed schemes are especially useful for a global networking service platform to integrate widely distributed user LANs into a single internetwork. The platform itself is an ATM-based frame forwarding network composed of access networks and a core network. These elemental networks are interconnected via edge nodes. In order to improve network interworking performance, these edge nodes should perform encapsulation processing without cell reassembly. Our proposal solves this problem. In the proposed schemes, when the first cell of a cell-divided access network frame arrives at an ingress edge node, a core-header-cell is generated from the IP header described in the first cell payload. This core-header-cell is first transmitted and then succeeding incoming cells including the first cell are forwarded cell-by-cell as soon as they arrive. Since cell-by-cell forwarding-processing reduces frame forwarding latency and cell buffer capacity, these schemes are effective from the viewpoint of both performance improvement and cost reduction.

A compact 120-GHz-band finline orthomode transducer (OMT) with high isolation between orthogonal ports (Iop) was designed and fabricated for bidirectional wireless data transmission with polarization multiplexing. To achieve high Iop, finline OMTs normally use a resistive card to decrease unwanted resonance, that occurs on the finline, but adding a resistive card complicates the fabrication process and raises the cost of fabrication. Our proposed finline OMT uses an improved finline design in which the resonance frequency is controlled in order to expel unwanted resonance from the operation bandwidth of the 120-GHz-band wireless link. The proposed finline design enables high Iop without using a resistive card, which simplifies the fabrication process and lowers the cost of fabrication. A square horn antenna, which is attached to the finline OMT, is also designed to suppress unwanted polarization rotation of reflected waves, which further improves Iop. The proposed finline OMT has a transmission loss of less than 1.2dB, return loss of more than 12dB, cross polarization discrimination of more than 30dB, and Iop of more than 50dB across the entire occupied bandwidth of the 120-GHz-band wireless link. These characteristics are sufficient not only for 10-Gbit/s bidirectional data transmission but also for 20-Gbit/s unidirectional 2-ch data transmission by polarization-multiplexing.

This article describes the frequency response and the applications of the optical electric-field sensor consisting of a 1 mm1 mm1 mm CdTe crystal mounted on the tip of an optical fiber, which theoretically possesses the potential to cover the frequency band from below megahertz to terahertz. We utilize a capacitor, GTEM-Cell, and standard gain horn antennas for applying a free-space electric field to the optical sensor at frequencies from 20 kHz to 1 GHz, from 1 GHz to 18 GHz, and from 10 to 180 GHz, respectively. An electric-field measurement demonstrates its flat frequency response within a 6-dB range from 20 kHz to 50 GHz except for the resonance due to the piezo-electric effect at a frequency around 1 MHz. The sensitivity increases due to the resonance of the radio frequency wave propagating in the crystal at the frequencies higher than 50 GHz. These experimental results demonstrate that the optical electric-field sensor is a superior tool for the wide-band measurement which is impossible with conventional sensors such as a dipole, a loop, and a horn antenna. In transient electrostatic discharge measurements, electric-field mapping, and near-field antenna measurements, the optical electric-field sensor provide the useful information for the deterioration diagnosis and the lifetime prognosis of electric circuits and devices. These applications of the optical electric-field sensor are regarded as promising ways for sowing the seeds of evolution in electric-field measurements for antenna measurement, EMC, and EMI.

This paper presents 10-Gbit/s bidirectional and 20-Gbit/s unidirectional wireless data transmission systems using 120-GHz-band finline orthomode transducers (OMTs). A new finline OMT was fabricated with two improved designs, to adapt it to the data transmission characteristics of the 120-GHz-band wireless link. One improvement is higher isolation between orthogonal ports and the other is lower group delay variation. The measured isolation is more than 59dB at the carrier frequency of the 120-GHz-band wireless link, and the measured group delay variation is 43ps. Using the finline OMT, we developed 10-Gbit/s bidirectional and 20-Gbit/s unidirectional wireless equipment that can transmit two channels of 10-Gbit/s data using polarization multiplexing. With this wireless equipment, we succeeded in 10-Gbit/s bidirectional and 20-Gbit/s unidirectional wireless data transmission, which leads to successful seamless connection to 10 Gigabit Ethernet and 12-ch high definition television signal transmission.

This paper investigates space and polarization multiplexing for multichannel transmission in a 120-GHz band wireless link system. The 120-GHz-band wireless equipment employs Cassegrain antennas with a gain of about 49dBi and cross-polar discrimination of 23dB. When each of two 120-GHz wireless links transmits a 10-Gbit/s data signal in the same direction over a distance of 800m, a bit error rate (BER) of below 10-12 is obtained when the receivers are set 30m apart. When forward error correction and polarization multiplexing are used for each wireless link, we can set two wireless links within 1m of each other and obtain a BER below 10-12. Moreover, we have experimentally shown that the rain attenuation of V- and H-polarization 120-GHz-band signal is almost the same.