This paper reviews our recent activities on nanophotonics based on a photonic crystal (PC)/quantum dot (QD)-combined structure for an all-optical device and a metal/semiconductor composite structure using surface plasmon (SP) and negative refractive index material (NIM). The former structure contributes to an ultrafast signal processing component by virtue of new PC design and QD selective-area-growth technologies, while the latter provides a new RGB color filter with a high precision and optical beam-steering device with a wide steering angle.

An all-optical switch based on a single photonic crystal defect with an air-bridge configuration and two-photon absorption was proposed, fabricated and characterized. In optical measurements, we obtained a sharp defect mode with a quality factor higher than 600 at 1.55 µm. More importantly, we observed its nonlinear response to the excitation of ultrashort pulses by utilizing two-photon absorption. Nonliner refractive index change of about -410-3 was achieved at a pumping power density of 3.6109 W/cm2.

We developed an electrically driven near-infrared broadband light source based on self-assembled InAs quantum dots (QDs). By combining emissions from four InAs QD ensembles with controlled emission center wavelengths, electro-luminescence (EL) with a Gaussian-like spectral shape and approximately 85-nm bandwidth was obtained. The peak wavelength of the EL was blue-shifted from approximately 1230 to 1200 nm with increased injection current density (J). This was due to the state-filling effect: sequential filling of the discrete QD electron/hole states by supplied carriers from lower (ground state; GS) to higher (excited state; ES) energy states. The EL intensities of the ES and GS emissions exhibited different J dependence, also because of the state-filling effect. The point-spread function (PSF) deduced from the Fourier-transformed EL spectrum exhibited a peak without apparent side lobes. The half width at half maximum of the PSF was 6.5 µm, which corresponds to the estimated axial resolution of the optical coherence tomography (OCT) image obtained with this light source. These results demonstrate the effectiveness of the QD-based device for realizing noise-reduced high-resolution OCT.

We have fabricated several two-dimensional photonic-crystal (2DPC) slab waveguides by using fine electron beam lithography and dry etching. The 2DPC waveguides include straight, bend, Y-branch, directional coupler, and coupled-cavity waveguides on the GaAs/AlGaAs substrate as an application to the ultra-small and ultra-fast all-optical switching device. Transmission spectra and near field patterns were characterized in a wide wavelength range from 850 to 1600 nm with the sample finished to the air-bridge type 2DPC slab. These waveguides appear to be suitable for achieving the waveguide platform in the symmetrical-Mach-Zehnder device.

We propose a built-in planar lens for coupling light to a waveguide on a 2-D photonic crystal (PhC) membrane. A 2-D PhC waveguide with the built-in lens has been fabricated with AlGaAs. Improvement in coupling performance is discussed in comparison to waveguides with straight ends as cleaved.

The optical properties of arrays of nanoholes and nanoslits in Al films were investigated both numerically and experimentally. The choice of Al was based on its low cost and ease of processing, in addition to the fact that it has a higher plasma frequency than gold or silver, leading to lower optical losses at wavelengths of 400 to 500nm.

We investigated optical transmission characteristics of aluminum thin films with periodic hole arrays in sub-wavelength. We divided white light into several color spectra using a color filter based on the surface plasmon resonance (SPR) utilizing aluminum showing high plasma frequency. By optimizing a hole-array period, hole shape, polarization and index difference of two surface, transmittance of 30% and full-width at half-maximum of around 100 nm were achieved.

We developed advanced techniques for the growth of self-assembled quantum dots (QDs) for fabricating a broadband light source that can be applied to optical coherence tomography (OCT). Four QD ensembles and strain reducing layers (SRLs) were grown in selective areas on a wafer by the use of a 90° rotational metal mask. The SRL thickness was varied to achieve appropriate shifts in the peak wavelength of the QD emission spectrum of up to 120 nm. The four-color QD ensembles were expected to have a broad bandwidth of more than 160 nm due to the combination of excited state emissions when introduced in a current-induced broadband light source such as a superluminescent diode (SLD). Furthermore, a desired shape of the SLD spectrum can be obtained by controlling the injection current applied to each QD ensemble. The broadband and spectrum shape controlled light source is promising for high-resolution and low-noise OCT systems.