This paper proposes a multibeam digital predistorter (DPD) that suppresses intercarrier interference caused by nonlinear distortions of power amplifiers (PAs) while reducing the power consumption of a multibeam array antenna transmitter. The proposed DPD reduces power consumption by allowing the final PAs of the array antenna transmitter to operate in a highly efficient nonlinear mode and compensating for the nonlinear distortions of the PAs with a unified dedicated DPD per subarray. Additionally, it provides the required high-quality signal transmission for high throughputs, such as realizing a 256-quadrature amplitude modulation (QAM) transmission instead of a 64-QAM transmission. Specifically, it adds an inverse-component signal to cancel the interference from an adjacent carrier of another beam. Consequently, it can suppress the intercarrier interference in the beam direction and improve the error vector magnitude (EVM) during the multibeam transmission, in which the frequency bands of the beams are adjacent. The experimental results obtained for two beams at 28.0 and 28.4GHz demonstrate that, compared with the previous single-beam DPD, the proposed multibeam DPD can improve the EVM. Also, they demonstrate that the proposed DPD can achieve an EVM value of <3%, which completely satisfies the 3GPP requirements for a 256-QAM transmission.

Non-linear behavioral models play a key role in designing digital pre-distorters (DPDs) for non-linear power amplifiers (NLPAs). In general, more complex behavioral models have better capability, but they should be converted into simpler versions to assist implementation. In this paper, a conversion from a complex fifth order inverse of a parallel Wiener (PRW) model to a simpler memory polynomial (MP) model is developed by using frequency domain expressions. In the developed conversion, parameters of the converted MP model are calculated from those of original fifth order inverse and frequency domain statistics of the transmit signal. Since the frequency domain statistics of the transmit signal can be precalculated, the developed conversion is deterministic, unlike the conventional conversion that identifies a converted model from lengthy input and output data. Computer simulations are conducted to confirm that conversion error is sufficiently small and the converted MP model offers equivalent pre-distortion to the original fifth order inverse.

This paper describes a method to design a predistorter (PD) for a GaN-FET power amplifier (PA) by using nonlinear parameters extracted from measured IMD which has asymmetrical peaks peculiar to a memory effect with a second-order lag. While, computationally efficient equations have been reported by C. Rey et al. for the memory effect with a first-order lag. Their equations are extended to be applicable to the memory effect with the second-order lag. The extension provides a recursive algorithm for cancellation signals of the PD each of which updating is made by using signals in only two sampling points. The algorithm is equivalent to a memory depth of two in computational efficiency. The required times for multiplications and additions are counted for the updating of all the cancellation signals and it is confirmed that the algorithm reduces computational intensity lower than half of a memory polynomial in recent papers. A computer simulation has clarified that the PD improves the adjacent channel leakage power ratio (ACLR) of OFDM signals with several hundred subcarriers corresponding to 4G mobile radio communications. It has been confirmed that a fifth-order PD is effective up to a higher power level close to 1 dB compression. The improvement of error vector magnitude (EVM) by the PD is also simulated for OFDM signals of which the subcarrier channels are modulated by 16 QAM.

In this paper, we propose a power amplifier linearization technique combined with iterative noise cancelation. This method alleviates the effect of added noises which prevents the predistorter (PD) from estimating the exact characteristics of the power amplifier (PA). To iteratively cancel the noise added in the feedback signal, the output signal of the power amplifier without noise is reconstructed by applying the inverse characteristics of the PD to the predistorted signals. The noise can be revealed by subtracting the reconstructed signals from the feedback signals. Simulation results based on the mean-square error (MSE) and power spectral density (PSD) criteria are presented to evaluate PD performance. The results show that the iterative noise cancelation significantly enhances the MSE performance, which leads to an improvement of the out-of-band power suppression. The performance of the proposed technique is verified by computer simulation and hardware test results.

To reduce laborious tasks of the phase determination, our previous paper has proposed a method to derive phase reference for two-tone intermodulation distortion (IMD) measurement of a power amplifier (PA) by using small-signal S-parameters. Since the method is applicable to low output power level, this paper proposes an iterative process to extend the applicable power level up to 1-dB compression. The iterative process is based on extraction of linear response: the principle of the extraction is described theoretically by using an accurate model of the PA with memory effect. Measurement of two-tone IMD is made for a GaN FET PA. Validity of the iteration is confirmed as convergence of the extracted linear response to that given by the product of S21 and input signal. Measured results also show validity of the physical model of the memory effect provided by Vuolevi et al. because beat frequency dependences of IMD's are accurately fitted by bias impedances at even order harmonics of envelope frequency. The PA is characterized by using measured results and the third and fifth order inverses of the PA are designed. Improvement of IMD is theoretically confirmed by using the inverses as predistorters.

Orthogonal frequency division multiplexing (OFDM) signals have high peak-to-average power ratio (PAPR) and cause large nonlinear distortions in power amplifiers (PAs). Memory effects in PAs also become no longer ignorable for the wide bandwidth of OFDM signals. Digital baseband predistorter is a highly efficient technique to compensate the nonlinear distortions. But it usually has many parameters and takes long time to converge. This paper presents a novel predistorter design using a set of orthogonal polynomials to increase the convergence speed and the compensation quality. Because OFDM signals are approximately complex Gaussian distributed, the complex Hermite polynomials which have a closed-form expression can be used as a set of orthogonal polynomials for OFDM signals. A differential envelope model is adopted in the predistorter design to compensate nonlinear PAs with memory effects. This model is superior to other predistorter models in parameter number to calculate. We inspect the proposed predistorter performance by using an OFDM signal referred to the IEEE 802.11a WLAN standard. Simulation results show that the proposed predistorter is efficient in compensating memory PAs. It is also demonstrated that the proposal acquires a faster convergence speed and a better compensation effect than conventional predistorters.

The adaptive predistorter and the negative feedback system are known as methods to compensate for the nonlinear distortion of a power amplifier. Although the feedback method is a simple technique, its instability impedes the capability of high-feedback gain to achieve a high-compensation effect. On the other hand, the predistorter requires a long time for convergence of the adaptive predistorters. In this paper, we propose a nonlinear distortion compensation method for a narrow-band signal. In this method, an adaptive predistorter and negative feedback are combined. In addition, to shorten the convergence time to minimize nonlinear distortion, a variable step-size (VS) method is also applied to the algorithm to determine the parameters of the adaptive predistorter. Using computer simulations, we show that the proposed scheme achieves both five times faster convergence speed than that of the predistorter and three times higher permissible delay time in the feedback amplifier than that of a negative feedback only amplifier.

This paper presents data on a reconfigurable predistorter for compensating the nonlinearity of a power amplifier in a system supporting both multimode and multiband operations. For compensation, the magnitude and phase response of a predistorter should be easy to tune to match that of a nonlinear amplifier that is used in various standards. That is to say, the predistorter should show decreasing magnitude followed by increasing magnitude, and the phase must initially lag and then lead, or lead and then lag, as a function of the increasing power input. In doing so, the power turning point, gain & phase deviation, and phase lead & lag should easily be controlled by the proposed reconfigurable predistorter using a bias control and impedance transformer. These characteristics are provided by the nonlinearity of the FET and the movement of the bias point caused by negative current generation. This proposed predistorter can be adopted for a system that uses Global System for Mobile communications (GSM), Code Division Multiple Access (CDMA) 800 MHz, and CDMA 1800 MHz. For example, by adopting this reconfigurable predistorter in a CDMA 1800 MHz, as much as 14 dB improvements in Adjacent Channel leakage Power Ratio (ACPR) at the 4 dB back off power level, can be achieved for the CDMA 1800 MHz signal.

In this paper, a predistorter using low frequency intermodulation (IM) signals is proposed. The harmonic generator of the proposed predistorter that consists of a hybrid coupler and four diodes biased separately extracts a second order low frequency IM signal. And with multiplication of second order IM signals, fourth order IM signal is obtained. A vector modulator, modulate fundamental signal with low frequency IM signals, generates predistortion IM signals and controls amplitude/phase of them with modulation factors. As a result, this predistorter is suppressed individual order intermodulation distortion signals of power amplifier effectively. The suggested predistorter has been manufactured to operate in Korea PCS base-station transmitting band (1840-1870 MHz). The test results show that the third order IM is cancelled more than 20 dB and the fifth order IM is cancelled about 10 dB for CW two-tone signals. Also, it's improved the adjacent channel power ratio (ACPR) more than 10 dB for CDMA (IS-95) signals.

A basestation power amplifier requires high linearity and stable operation for common amplification of a multiplexed wideband signal. Nonlinearity compensation techniques with the feedforward or predistorter are useful for this purpose. This paper presents a predistortion amplifier with automatic control at RF band for application at a basestation. In this method, the predistorter distorts an RF input signal by referring to a look-up table (LUT) corresponding to the input power. Out-of-band radiation power are directly monitored at IF band to determine the LUT. A DSP with an iterative algorithm updates the content of the LUT to minimize the out-of-band radiation power. Computer simulation experiment is carried out. The use of this proposed method promises a highly linear wideband and high power-efficiency amplifier.

Orthogonal frequency division multiplexing (OFDM) signals suffer nonlinear distortion within the transmitter, in the high-power amplifiers in particular. This paper proposes a nonlinear distortion compensation technique for OFDM signals, which incorporates a baseband predistortion with a constant peak-power OFDM (CP-OFDM). CP-OFDM fixes the envelope-peak amplitude to a constant value while maintaining the linearity of the inverse fast Fourier transform (IFFT) outputs; consequently, the baseband predistorter entirely compensates the nonlinear distortion. Simulation and experimental results verify that the proposed technique significantly reduces out-of-band power emission and adjacent channel interference (ACI) more than 10 dB respectively.

This paper describes the performance of a predistorter implementation to a superluminescent diode (SLD) in fiber-optic wireless systems under the optical reflection. SLD intensity noise and 3rd-order intermodulation distortion (IM3) are experimentally compared with those of DFB-and FP-LD. It is observed that the IM3 of SLD has ideal 3rd characteristics and output noise remains unchanged against the number of optical connectors. It is also found that the predistorter reduces IM3 by 8 dB. Receiver sensitivity of the system is discussed from the view point of overall design. the BER performance of an SLD with predistorter using a π/4-QPSK signal as a subcarrier is also described theoretically and experimentally.