With increases in frequency and density of RISC microprocessors due to rapid advances in architecture, circuit and fine device technologies, power consumption becomes a bigger concern. Supply voltage should be reduced from 5 V to 3.3 V. In this paper, several novel circuits using 0.5µm BiCMOS technology are proposed. These can be applied to a superscalar RISC microprocessor at 3.3 V power supply or below. High speed and low power consumption characteristics are achieved in a floating-point data path, an integer data path and a TLB by using the proposed circuits. The three concepts behind the proposed high speed circuit techniques at low voltage are summarized as follows. There are a number of heavy load paths in a microprocessor, and these become critical paths under low voltage conditions. To achieve high speed characteristics under heavy load conditions without increasing circuit area, low voltage swing operation of a circuit is effective. By exploiting the high conductance of a bipolar transistor, instead of using an MOS transistor, low swing operation can be got. This first concept is applied to a single-ended common-base sense circuit with low swing data lines in the register file of a floating and an integer data path. Both multi-series transistor connections and voltage drops by Vth of MOS transistors and Vbe of bipolar transistors also degrade the speed performance of a circuit. Then the second concept employed is a wired-OR logic circuit technique using bipolar transistors which is applied to a comparator in the TLB instead of multi-series transistor connections of CMOS circuits. The third concept to overcome the voltage drops by Vth and Vbe is addition of a pull up PMOS to both the path logic adder and the BiNMOS logic gate to ensure the circuits have full swing operation.
The copyright of the original papers published on this site belongs to IEICE. Unauthorized use of the original or translated papers is prohibited. See IEICE Provisions on Copyright for details.
Copy
Fumio MURABAYASHI, Tatsumi YAMAUCHI, Masahiro IWAMURA, Takashi HOTTA, Tetsuo NAKANO, Yutaka KOBAYASHI, "BiCMOS Circuit Techniques for 3.3 V Microprocessors" in IEICE TRANSACTIONS on Electronics,
vol. E76-C, no. 5, pp. 695-700, May 1993, doi: .
Abstract: With increases in frequency and density of RISC microprocessors due to rapid advances in architecture, circuit and fine device technologies, power consumption becomes a bigger concern. Supply voltage should be reduced from 5 V to 3.3 V. In this paper, several novel circuits using 0.5µm BiCMOS technology are proposed. These can be applied to a superscalar RISC microprocessor at 3.3 V power supply or below. High speed and low power consumption characteristics are achieved in a floating-point data path, an integer data path and a TLB by using the proposed circuits. The three concepts behind the proposed high speed circuit techniques at low voltage are summarized as follows. There are a number of heavy load paths in a microprocessor, and these become critical paths under low voltage conditions. To achieve high speed characteristics under heavy load conditions without increasing circuit area, low voltage swing operation of a circuit is effective. By exploiting the high conductance of a bipolar transistor, instead of using an MOS transistor, low swing operation can be got. This first concept is applied to a single-ended common-base sense circuit with low swing data lines in the register file of a floating and an integer data path. Both multi-series transistor connections and voltage drops by Vth of MOS transistors and Vbe of bipolar transistors also degrade the speed performance of a circuit. Then the second concept employed is a wired-OR logic circuit technique using bipolar transistors which is applied to a comparator in the TLB instead of multi-series transistor connections of CMOS circuits. The third concept to overcome the voltage drops by Vth and Vbe is addition of a pull up PMOS to both the path logic adder and the BiNMOS logic gate to ensure the circuits have full swing operation.
URL: https://global.ieice.org/en_transactions/electronics/10.1587/e76-c_5_695/_p
Copy
@ARTICLE{e76-c_5_695,
author={Fumio MURABAYASHI, Tatsumi YAMAUCHI, Masahiro IWAMURA, Takashi HOTTA, Tetsuo NAKANO, Yutaka KOBAYASHI, },
journal={IEICE TRANSACTIONS on Electronics},
title={BiCMOS Circuit Techniques for 3.3 V Microprocessors},
year={1993},
volume={E76-C},
number={5},
pages={695-700},
abstract={With increases in frequency and density of RISC microprocessors due to rapid advances in architecture, circuit and fine device technologies, power consumption becomes a bigger concern. Supply voltage should be reduced from 5 V to 3.3 V. In this paper, several novel circuits using 0.5µm BiCMOS technology are proposed. These can be applied to a superscalar RISC microprocessor at 3.3 V power supply or below. High speed and low power consumption characteristics are achieved in a floating-point data path, an integer data path and a TLB by using the proposed circuits. The three concepts behind the proposed high speed circuit techniques at low voltage are summarized as follows. There are a number of heavy load paths in a microprocessor, and these become critical paths under low voltage conditions. To achieve high speed characteristics under heavy load conditions without increasing circuit area, low voltage swing operation of a circuit is effective. By exploiting the high conductance of a bipolar transistor, instead of using an MOS transistor, low swing operation can be got. This first concept is applied to a single-ended common-base sense circuit with low swing data lines in the register file of a floating and an integer data path. Both multi-series transistor connections and voltage drops by Vth of MOS transistors and Vbe of bipolar transistors also degrade the speed performance of a circuit. Then the second concept employed is a wired-OR logic circuit technique using bipolar transistors which is applied to a comparator in the TLB instead of multi-series transistor connections of CMOS circuits. The third concept to overcome the voltage drops by Vth and Vbe is addition of a pull up PMOS to both the path logic adder and the BiNMOS logic gate to ensure the circuits have full swing operation.},
keywords={},
doi={},
ISSN={},
month={May},}
Copy
TY - JOUR
TI - BiCMOS Circuit Techniques for 3.3 V Microprocessors
T2 - IEICE TRANSACTIONS on Electronics
SP - 695
EP - 700
AU - Fumio MURABAYASHI
AU - Tatsumi YAMAUCHI
AU - Masahiro IWAMURA
AU - Takashi HOTTA
AU - Tetsuo NAKANO
AU - Yutaka KOBAYASHI
PY - 1993
DO -
JO - IEICE TRANSACTIONS on Electronics
SN -
VL - E76-C
IS - 5
JA - IEICE TRANSACTIONS on Electronics
Y1 - May 1993
AB - With increases in frequency and density of RISC microprocessors due to rapid advances in architecture, circuit and fine device technologies, power consumption becomes a bigger concern. Supply voltage should be reduced from 5 V to 3.3 V. In this paper, several novel circuits using 0.5µm BiCMOS technology are proposed. These can be applied to a superscalar RISC microprocessor at 3.3 V power supply or below. High speed and low power consumption characteristics are achieved in a floating-point data path, an integer data path and a TLB by using the proposed circuits. The three concepts behind the proposed high speed circuit techniques at low voltage are summarized as follows. There are a number of heavy load paths in a microprocessor, and these become critical paths under low voltage conditions. To achieve high speed characteristics under heavy load conditions without increasing circuit area, low voltage swing operation of a circuit is effective. By exploiting the high conductance of a bipolar transistor, instead of using an MOS transistor, low swing operation can be got. This first concept is applied to a single-ended common-base sense circuit with low swing data lines in the register file of a floating and an integer data path. Both multi-series transistor connections and voltage drops by Vth of MOS transistors and Vbe of bipolar transistors also degrade the speed performance of a circuit. Then the second concept employed is a wired-OR logic circuit technique using bipolar transistors which is applied to a comparator in the TLB instead of multi-series transistor connections of CMOS circuits. The third concept to overcome the voltage drops by Vth and Vbe is addition of a pull up PMOS to both the path logic adder and the BiNMOS logic gate to ensure the circuits have full swing operation.
ER -