This paper studies a multiband mobile communication system to support both high data rate services and wide service coverage, using high and low frequency resources with different propagation characteristics. In the multiband system, multiple frequency bands are managed by a base station and one of the frequency bands is adaptively allocated to a terminal depending on his channel quality. By limiting the low frequency resources to a terminal not covered by the higher frequencies, the presented multiband system can accommodate many terminals providing wide coverage area, as if all radio resources have low frequency. From numerical results, the multiband system can provide wide service coverage area for much larger number of terminals than conventional systems. It is also found that an appropriate balance of multiple frequency resources is essential to achieve high capacity.

This paper proposes a new partial channel state information (CSI) reporting method for spatial scheduling in TDD/MIMO systems. In the proposed method, a terminal transmits pilot signals using transmit beams which have large channel gains between the base station (BS) and the terminal. Then, the BS can obtain partial CSI through responses of the pilot signals. Furthermore, adaptive allocation of pilot signals is proposed, in which pilot signals for CSI reporting are adaptively allocated to terminals depending on the number of terminals. We evaluate system throughput of spatial scheduling under the partial CSI reporting from multiple terminals. Numerical results show that the proposed method reduces uplink signalling for CSI reporting effectively, keeping high system throughput of spatial scheduling.

This paper provides insights on the status of broadband optical access market and technologies in Europe and on the expected trends for the next generation optical access networks. The final target for most operators, cities or any other player is of course FTTH (Fibre To The Home) deployment although we can expect intermediate steps with copper or wireless technologies. Among the two candidate architectures for FTTH, PON (Passive Optical Network) is by far the most attractive and cost effective solution. We also demonstrate that Ethernet based optical access network is very adequate to all-IP networks without any incidence on the level of quality of service. Finally, we provide feedback from a FTTH pilot network in Colmar (France) based on Gigabit Ethernet PON technology. The interest of this pilot lies on the level of functionality required for broadband optical access networks but also on the development of new home network configurations.

This paper proposes pilot-based channel quality reporting for orthogonal frequency division multiple access/time division duplex (OFDMA/TDD) systems with cochannel interference. In the proposed method, a terminal reports his channel quality in multiple subbands to base station (BS) using channel reciprocity of TDD systems. The terminal transmits uplink pilot signals in the subbands with different transmit power which is inversely proportional to the subband-based interference power. The BS can obtain knowledge of the terminal's received signal-to-interference-plus-noise power ratio on subband basis, measuring the pilot signal power. In performance evaluation, accuracy of channel quality reporting and amount of uplink signalling are examined. From numerical results, it is found that the proposed method becomes effective as the number of subbands and terminals for channel quality reporting increases.

A new shared multibuffer architecture for high-speed ATM (Asynchronous Transfer Mode) switch LSIs is described. Multiple buffer memories are located between two crosspoint switches. By controlling the input-side crosspoint switch so as to equalize the utilization rate of each buffer memory, these multiple buffer memories can be recognized as a single large shared buffer memory. High utilization efficiency of buffer memory can thus be achieved, and the cell loss ratio is minimized. By accessing the buffer memories in parallel via crosspoint switches, the time required to access the buffer memories is greatly reduced. This feature enables high-speed operation of the switch. The shared multibuffer architecture was implemented in a switch LSI using 0.8-µm BiCMOS process technology. Experimental results revealed that this chip can operate at more than 125 MHz. Bit-sliced eight switch LSIs operating at 78 MHz construct a 622-Mb/s 88 ATM switching system with a buffer size of 1,024 ATM cells. Power consumption of the switch LSI was 3 W.

This paper proposes a pilot-based channel state information (CSI) feedback from a terminal to a base station (BS), considering the terminal's co-channel interference in a time-division duplex/multi-input multi-output system. In the proposed method, the terminal determines a precoding matrix according to the terminal's co-channel interference characteristics and transmits the precoded pilot signals on uplink. Using the responses of the precoded pilot signals, the BS determines appropriate weight vectors for downlink transmit beams considering the terminal's interference characteristics. Furthermore, the BS can predict the terminal's output signal-to-interference-plus-noise power ratio (SINR) for the downlink data stream. Numerical results show that the BS can achieve efficient transmission and accurate SINR prediction using the proposed CSI feedback.

A new ATM switch architecture, named shared multibuffering, features great advantages on memory access speed for a large switch, and overall size of buffer memories to achieve excellent cell-loss performance. We have developed a 622-Mb/s 88 shared multibuffer ATM switch with multicast functions and hierarchical queueing functions to accommodate 156-Mb/s, 622-Mb/s and 2.4-Gb/s interfaces. Implementation of the shared multibuffer ATM switch is described with respect to the four sorts of 0.8-µm BiCMOS LSIs and ATM switch boards. The switch board/type-1, with C1-LSI, allows to accommodate effectively 156-Mb/s and 622-Mb/s interfaces, which is suitable for an ATM access system. The switch board/type-2, with C2-LSI, can provide multicast functions and accommodate a 2.4-Gb/s interface. By using four switch boards, it is possible to apply them to a 2.4-Gb/s ATM loop system.

This paper proposes a new control scheme in which the base station (BS) controls terminal's transmit beamforming in time-division duplex (TDD)/multi-input multi-output (MIMO) systems. In the proposed scheme, the BS transmits pilot signals using appropriate downlink beams to instruct a terminal on target transmit beamforming. Using responses of the downlink pilot signals, the terminal can perform transmit beamforming close to the target one. Our theoretical investigation reveals that the BS can control multiple terminals' transmit beamforming simultaneously. Furthermore, an efficient signal processing at the terminal is investigated to obtain precise weight of transmit beamforming in noise environments. Numerical results show that the terminal can perform precise transmit beamforming close to the target one in noise environments. It is also shown that the amount of downlink control signalling in the proposed scheme is much less than that in codebook-based approach.