A radial line slot antenna (RLSA) is a high gain and high efficiency planar antenna proposed for DBS subscribers. Spirally arrayed slots are excited by a cylindrical wave with the rotational symmetry. In a small sized antenna where large slot coupling is adopted, aperture efficiency reduction due to rotational asymmetry associated with a spiral arrangement of the slots becomes notable. Authors proposed a RLSA with a concentric slot arrangement excited by a rotating mode in order to enhance the rotational symmetry. This is the first report of the normal operation of a rotating mode RLSA fed by a cavity resonator. The experiments confirm the basic operation of this novel antenna; the gain of 27.8dBi and the efficiency of 68% is measured at 11.85GHz for the RLSA with 0.24mφ.

This paper presents the loss factors in the post-wall waveguide-fed parallel-plate slot array antenna in the millimeter-wave band. At first, transmission loss is evaluated per unit length by measuring the losses of post-wall waveguides on various substrates with different thicknesses in different bands. Measured results of the frequency dependence agree with theoretical predictions using the effective conductivity and the complex permittivity obtained by the whispering gallery mode resonator method. Then the authors evaluate the antennas with various sizes at 76.5 GHz. The antenna efficiency is evaluated by taking into account the loss factors related to: the transmission loss both in the feed and the parallel plate waveguides, the aperture efficiency and the insertion loss and the reflection of the transition. Also, the loss due to the locally-perturbed currents by the slot radiation is evaluated. The sum of the losses in the prediction quantitatively agrees with the measurement.

This paper verifies the accuracy of PO as applied to the scattering of dipole waves by a finite size reflector which is composed of strips on a grounded dielectric slab. By using the closed form expressions of reflected waves from the surface, PO calculation can be conducted straightforwardly. The calculated results are compared with the experimental ones for vertical and horizontal dipoles over a circular reflector.

Transitions between a post-wall waveguide and a microstrip line are proposed as the key components for cost-effective millimeter-wave modules. A transition with a coaxial structure is investigated for LTCC laminated layers and 11.3% bandwidth for the reflection smaller than -15 dB is realized in 60 GHz band. The overall connector loss with 1 cm post-wall would be about 0.8 dB. The degradation due to fabrication error is also assessed. The transition in LTCC substrate fulfills electrical and manufacturing demands in millimeter-wave bands.

A wideband design of the waveguide short-slot 2-plane coupler with 2×2 input/output ports is designed, fabricated, and evaluated. Using coupling coefficients of complementary propagating modes which are TE11, TE21, and TE30 modes, the flatness of the output amplitudes of 2-plane coupler is improved. The coupler operates from 4.96GHz to 5.27GHz (bandwidth 6.1%) which is wider than the former coupler without considering the complementary propagating mode from 5.04GHz to 5.17GHz (bandwidth 2.5%).

Accuracy of PTD is evaluated for a plane wave diffraction from a large circular disk, ten wavelength in diameter. On the analogy of offset reflector antennas, diffracted fields in the incident plane and the plane perpendicular to this is discussed. The excellent accuracy of PTD is demonstrated, while the principal errors are identified as the results of the secondary diffraction. The results by PO are also discussed and its envelope error is given in closed forms. Serious errors of PO in polarization prediction is also pointed out.

A novel design technique for two-dimensional (2-D) waveguide slot arrays is proposed in this paper that combines a full-wave method of moments (MoM) analysis and an equivalent circuit with the explicit restraint of input matching. The admittance and slot spacing are determined first in an equivalent circuit to realize the desired distribution of power dissipation and phase, with the explicit restraint of input matching. Secondly by applying a full-wave MoM analysis to the finite 2-D array, slot parameters are iteratively determined to realize the active admittance designed above where slot mutual coupling and wall thickness are fully taken into account. The admittance, treated as the key parameter in the equivalent circuit corresponds to the power dissipation of the slots but not to the slot voltage, which is directly synthesized from the radiation pattern. The initial value of the power dissipation is assumed to be proportional to the square of the amplitude of the desired slot voltage. This assumption leads to a feedback procedure, because the resultant slot voltage distribution generally differs from the desired ones due to the effect of non-uniformity in the characteristic impedance on slot apertures. This slot voltage error is used to renew the initial distribution of power dissipation in the equivalent circuit. Generally, only one feedback cycle is needed. Two 2427-element arrays with uniform and Taylor distributions were designed and fabricated at 25.3 GHz. The measured overall reflections for both antennas were suppressed below -18 dB over the 24.3-26.3 GHz frequency range. High aperture efficiencies of 86.8% and 55.1% were realized for the antennas with uniform and Taylor distributions, the latter of which has very low sidelobes below -33 dB in both the E- and H-planes.

Interfaces between a coaxial structure and a post-wall waveguide are proposed as the essential components for cost-effective millimeter-wave modules. PTFE substrate is selected in terms of loss and manufacturability. The reflection and the transmission characteristics are investigated. The short-stepped and the short-taper-stepped feeding structures provide 14.7% and 13.2% bandwidths for the reflection smaller than -15 dB, respectively. The 4640 mm2 size antenna fed by the short-stepped structure in PTFE substrate gives 27.3 dBi with 58.2% efficiency at 60.0 GHz. Feeding structures in PTFE substrate fulfill electrical and manufacturing demands in millimeter-wave bands.

A point-to-point fixed wireless access (FWA) system with a maximum throughput of 1Gbps has been developed in the 39GHz band. A double-layer plate-laminated waveguide slot array antenna is successfully realized with specific considerations of practical application. The antenna is designed so as to hold the VSWR under 1.5. The antenna input as well as feeding network is configured to reduce the antenna profile as well as the antenna weight. In addition, integrating the antenna into a wireless terminal is taken into account. A shielding wall, whose effectiveness is experimentally demonstrated, is set in the middle of the wireless terminal to achieve the spatial isolation of more than 65dB between two antennas on the H-plane. 30 test antennas are fabricated by diffusion bonding of thin metal plates, to investigate the tolerance and mass-productivity of this process. An aluminum antenna, which has the advantages of light weight and anti-aging, is also fabricated and evaluated with an eye to the future.

This paper presents a novel 60 GHz-band photonic-integrated array-antenna and module for radio-over-fiber (RoF)-based beam forming. An integrated photonic array-antennas (IPA), where eight photodiodes and 4×2 arrayed patch-antenna are integrated in a single board, is actually fabricated, and 3.5-Gbit/s QPSK digital signal transmission with beam forming of the IPA is experimentally demonstrated. In addition, a novel 60-GHz compact antenna module is proposed and fabricated for increasing the number of antenna elements and flexibility creating various beam patterns. The feasibility of beam forming operation for the proposed antenna module is confirmed by a 60-GHz RoF transmission experiment. The capability of detecting the mobile terminal direction, which is one of the indispensable functions for actual environment, is also studied. The obtained results in this paper will be useful for designing future radio access networks based on RoF transmission technology.

A Circularly-Polarized Radial Line Slot Antenna (CP-RLSA) is a high gain planar antenna for DBS reception. From the practical point of view, it is necessary to overlook the performance of RLSA as a function of various design parameters. This paper presents the general design of CP-RLSA with uniform slot density and predicts the bandwidth and the gain of RLSA by array antenna analysis. In the calculation, the slot coupling is evaluated by full wave analysis and the effects of all the design parameters are taken into account. The long line effect reduces the bandwidth of RLSA monotonously with the antenna diameter. The bandwidth is limited by slot resonance as well and the overall bandwidth is less dependent of the diameter. 3dB bandwidth of 650 MHz is predicted for antenna diameter of 600 mm, for example. Among various design parameters, permittivity of slow wave structure affects the bandwidth and gain considerably; εγ1.41.8 is preferable. On the other hand, the height of waveguide and the slot pair angular spacing have little influence, though lower waveguide and smaller spacing are advantageous for a stable rotational symmetry of inner field.

The authors realize a 50% length reduction of short-slot couplers in a post-wall dielectric substrate by two techniques. One is to introduce hollow rectangular holes near the side walls of the coupled region. The difference of phase constant between the TE10 and TE20 propagating modes increases and the required length to realize a desired dividing ratio is reduced. Another is to remove two reflection-suppressing posts in the coupled region. The length of the coupled region is determined to cancel the reflections at both ends of the coupled region. The total length of a 4-way Butler matrix can be reduced to 48% in comparison with the conventional one and the couplers still maintain good dividing characteristics; the dividing ratio of the hybrid is less than 0.1 dB and the isolations of the couplers are more than 20 dB.

A radial line slot antenna (RLSA) is a high gain and high efficiency planar antenna for DBS reception and VSAT terminals. To generalize the slot design of RLSA, it is necessary to estimate the radiation, reflection and the transmission characteristics of a slot. This paper presents an equivalent circuit of a slot on radial waveguide. A periodic structure model is used in the moment method analysis, to simulate the slot coupling in rotationally symmetric antenna operation in the oversized radial line. Radiation and reflection coefficients are expressed in the S-matrix form; the slot length dependence of the matrix element is discussed.

Extremely small aperture radial line slot antennas (RLSAs) are analyzed by method of moments. At first, the analysis model of cylindrical waveguide in terms of rectangular cavity modes is confirmed for a RLSA with a spiral slot arrangement. The overall VSWR as well as rotational symmetry of the actual structure of RLSAs is predicted for the first time and is confirmed experimentally. Secondly, the minimum diameter of the concentric array RLSA is estimated for which the conventional analysis model of a rectangular waveguide is valid for the design of matching slot pairs at the shorted periphery of the radial waveguide. It is found that the curvature and cylindrical short wall at aperture periphery must be considered in the design and analysis of small RLSAs with the gain lower than about 25 dBi.

This paper describes the characteristics of a one dimensional narrow-wall slotted waveguide array with a single-layer linear-to-circular polarization converter consisting of a dipole array. An external boundary value problem of one slot and three dipoles, which approximates the mutual coupling between the dipole array and an edge slot extending over three faces of a rectangular waveguide, is formulated and analyzed by the method of moments; design of polarization conversion is conducted for this model as a unit element. If every unit element has perfect circular polarization, grating lobes appear in the array pattern due to the alternating slot angle: these are suppressed in this paper by changing the dipole angle and degrading the axial ratio of the unit element. The validity of the design is confirmed by the measurements. The dipole array has negligible effects upon slot impedance; the polarization conversion for existing narrow-wall slotted arrays is realized by add-on dipole array.

Equivalence of physical optics (PO) and aperture field integration method (AFIM) in the full 360 observation angle is discussed for polyhedron approximate reflectors; the necessary conditions of integration surface in AFIM for the equivalence to PO are presented. In addition to the condition that complete equivalent currents consisting of both geometrical optics (GO) reflected fields from the reflector and direct incident fields from the feed source are used, the integration surface should cap the reflector perfectly and should be in the illuminated region of the GO reflected field. Validity of the conditions is numerically confirmed for a two-dimensional (2-D) strip reflector, 3-D corner reflectors and a 2-D polyhedron approximate reflector.

60 GHz band conical beam radial line slot antennas (RLSA's) are designed and fabricated. Antennas are made of PTFE substrate with copper for high accuracy and mass producibility in millimeter wave frequency. The radiation pattern such as directivity and beam direction can be controlled by changing the excitation of slots. The measured radiation pattern is in reasonable agreement with the predicted one in main beam direction. The measured gain is about 2.5 dB smaller than the predicted gain.

Resonant slots are widely used for conventional slotted waveguide array. Reflection from each slot causes a standing wave in the waveguide and beam tilting technique is essential to suppress the reflection at the antenna input port. But the slot reflection narrows the overall frequency bandwidth and the design taking it into account is complicated. This paper proposes a reflection cancelling slot pair as an array element, which consists of two slots spaced by 1/4λg. Round trip path-length difference between them is 1/2λg and reflection waves from a pair disappear and traveling-wave excitation in the waveguide is realized. The full wave analysis reveals that mutual coupling between paired slots is large and seriously reduces the radiation from a pair. Offset arrangement of slots in a pair is recommended to decrease the mutual coupling and to realize strong coupling. In practical array design, the mutual couplings from other pairs were simulated by imposing periodic boundary conditions above the aperture. To clarify the advantages of the slot pair over a conventional resonant slot, the predicted characteristics are compared. Reflection characteristics of the array using the slot pair is excellent and a boresite beam array can be realized. In addition, a slot pair can realize stronger coupling than the conventional resonant slot, while the bandwidth of the former in terms of the aperture field phase illumination is narrower than that of the latter. These suggests that the slot pair array is much more suitable for a small array than conventional one. Finally, the predicted characteristics are confirmed by experiments.

Locality in high frequency diffraction is embodied in the Method of Moments (MoM) in view of the method of stationary phase. Local-domain basis functions accompanied with the phase detour, which are not entire domain but are much larger than the segment length in the usual MoM, are newly introduced to enhance the cancellation of mutual coupling over the local-domain; the off-diagonal elements in resultant reaction matrix evanesce rapidly. The Fresnel zone threshold is proposed for simple and effective truncation of the matrix into the sparse band matrix. Numerical examples for the 2-D strip and the 2-D corner reflector demonstrate the feasibility as well as difficulties of the concept; the way mitigating computational load of the MoM in high frequency problems is suggested.

This paper presents the design of low sidelobe single-layer slotted waveguide arrays. The Taylor distribution with -25 dB sidelobe level is synthesized in two orthogonal directions in the aperture. The multiple-way power divider consisting of a cascade of novel π-junctions is introduced; each π-junction, two-way power divider, is so designed as to accept unequal power dividing by adopting an offset window. The smooth Taylor distribution is realized at the output of the multiple-way power divider, which was originally developed only for uniform distribution. A model antenna for Taylor distribution is tested at 76 GHz. The measured sidelobe level is below -24 dB in both E- and H-plane. The highest gain is 34.5 dBi with 50% efficiency which is only 15% lower than that for uniform aperture illumination.