In this paper, we propose an interference canceller for asynchronous DS-CDMA. The principle is based on parallel cancellation using soft decision(PCSD), however, we propose to add an operation to suppress the strength of interfering signals replica on PCSD. We show here that this operation plays a very important theoretical role in PCSD, and that the performance of our proposed scheme approaches that of a perfect decorrelating detector under certain conditions. With this theoretical background in mind, we named this scheme the "Near-Decorrelating Multistage Detector"(NDMD). To demonstrate NDMD performance, we performed two kinds of computer simulations. In the first kind of simulation, simple conditions are assumed in order to evaluate basic cancelling performance. In the other kind of simulation, essential techniques for CDMA cellular systems such as FEC, transmission power control(TPC), and base band filtering were implemented while taking into account NDMD as applied to such systems. These simulations numerically demonstrate that NDMD is very efficient in cancelling out interference and that it improves asynchronous DS-CDMA performance.

Vehicular speed response phase locked loop (VSR-PLL) is a novel circuit to remove a steady-state frequency offset which arises in the receiver with directive antenna. In this paper, the circuit is applied to Ricean fading environment. For the application of VSR-PLL to Ricean statistics channel, the Doppler shift information of direct wave must be obtained because the self-oscillation frequency of VCO is controlled by using the information. This paper describes an estimation method for the Doppler shift of the direct wave, and shows the several results of the performance analysis for the estimation method and proposed VSR-PLL with the method. As a result, we found that the proposed VSR-PLL could reduce the irreducible bit-error rate for QPSK system from about 10-2 to 10-3 on several conditions.

In the multipath mobile channel, the received signal suffers from both the fluctuation in the received field intensity caused by fading and waveform distortion caused by the echo. Diversity reception using multiple spaced antennas is an effective method to compensate for fading, while echo cancellation with an adaptive array is good at compensating for waveform distortion. In this paper, an adaptive switching echo cancellation/diversity reception method to compensate for both waveform distortion and fading is proposed. The proposed switching reception monitors the impacts of channel conditions on received signal and then one of an echo canceller and a diversity receiver is selected accordingly to compensate the channel. The compensation performance of the proposed switching reception in terms of both average DUR (Desired to Undesired signal Ratio) and the probability of DUR below a threshold value is investigated with computer simulation. The results show that the adaptive switching echo cancellation/diversity reception has realized the advantages of both adaptive echo cancellation and diversity reception.

In this paper, we propose a teletraffic model and evaluate the performance in the terrestrial/satellite integrated mobile communication networks having hierarchical structure consisting of terrestrial microcell and satellite spot beam. In the proposed teletraffic model, both the subscriber terminal mobility in the terrestrial microcell and the satellite mobility in the LEO satellite spot beam are considered. The overflow traffic from microcell can be accommodated by the satellite spot beam and is analyzed by IPP (Interrupted Poisson Process) which is often used to analyze non-random overflow traffic. Various reservation channels for handoff calls in terrestrial microcell and satellite spot beam are considered. New calls initially directed to the satellite spot beam are also considered for reservation channels. Carried traffic, blocking, forced termination and non-completion probabilities are evaluated for the overall integrated networks.

Mobile databases will play an important role in mobile computing environment, to provide data storing and data retrieval functionalities which are needed by most applications. In mobile computing environment, the wireless communication poses some problems, which require us to minimize its use. Replication is a database technique that is commonly used to fulfill the requirement in minimizing network usage. In this paper, we propose two replica allocation strategies, called primary-copy tracking replica allocation (PTRA) and user majority replica allocation (UMRA), which are better suited to the mobile computing environment. Their proposals are intended to cope with cost performance issues in data replication due to user mobility in mobile computing environment. To investigate their effectiveness, we provide access cost analysis and comparison on these strategies and the static replica allocation (SRA) strategy. We show that our proposed strategies outperform the SRA strategy when user mobility (inter-cell movement) is relatively low as compared with data access rate.

Fast transmit power control (TPC) adaptively controls the mobile terminal transmit power so that the instantaneous signal-to-interference plus background noise ratio's (SIR's) of received signals of all users at the base station receiver are kept at the target value to avoid the adverse effect of multipath fading as well as the near/far problem. This paper theoretically analyzes the power efficiency of power controlled DS-CDMA reverse link assuming ideal Rake combining under multi-user and multipath Rayleigh fading environments. The achievable bit error rate (BER) performance is evaluated as a function of average and peak transmit powers required at mobile terminals. The effect of number of resolved paths is discussed. It is shown that the required peak transmit power with fast TPC is larger than that without fast TPC for relatively large BER values; however, when the link is interference-limited, fast TPC achieves significantly larger link capacity.

The bit error rate (BER) performance against average Eb/No (signal energy per bit-to-noise power spectral density ratio) and the capacity of the pilot symbol-assisted coherent orthogonal filter (PSA-COF) based Rake receiver with fast transmit power control (TPC) are evaluated in DS-CDMA reverse link under multipath Rayleigh fading. Fast TPC, which controls all signals transmitted from users in the same cell or sector such that they are received with equal power at the cell site under fast Rayleigh fading, is essential for the PSA-COF based Rake receiver in the reverse link in order to improve the performance degradation experienced when the received signal level drops due to fading as the transmit power is limited in practical systems. Signal-to interference plus noise power ratio (SINR) based fast transmit power control (TPC) is assumed here. By using the fast TPC in reverse link and applying the PSA-COF based Rake receiver to base station (BS), the transmit power of each mobile station (MS) can be significantly reduced, thus increasing link capacity. It is demonstrated that the capacity of the PSA-COF based Rake receiver is about 1.5 times higher than that of the conventional matched filter (MF) receiver in interference-limited channels.

A slotted ALOHA direct sequence spread spectrum system with random signatures is considered. The system is applicable in cases where a large number of terminals transmit to a single hub station like in cellular digital radio, personal mobile systems and wireless LANs. It is shown that significant improvements in packet throughput capacity are obtained if the adaptive receiver structures are used. Systems for the comparison are the spread spectrum slotted ALOHA system and the conventional slotted ALOHA system.

Low-voltage technology in front-end GaAs IC for mobile communication equipment will be presented. New techniques in combination with different threshold voltage (Vth) FETs for an amplifier and a mixer were investigated for low-voltage operation of the IC. The amplifier and mixer consist of a cascode connected to FETs with shallow and deep Vth. The best suitable distribution of the supply voltages was accomplished for each FETs by using a combination of different Vth, and excellent RF characteristics of the IC were obtained, even at low voltage operation. In addition, this front-end IC has a high image rejection ratio (IRR) without using an external image rejection filter, but by using high Q-value input and intermediate matching circuits. The fabrication process used an asymmetric self-aligned BP-LDD process and high dielectric constant (high-εr) on-chip bypass capacitors using SrTiO3 contributed to a reduction in dissipation current, chip size and parasitic reactance in the source wires. The fabricated IC showed a conversion gain (CG) of 23 dB, noise figure (NF) of 2.8 dB, 3rd order output intercept point (IP3out) of 3 dBm, image rejection ratio (IRR) over 20 dBc and LO to RF isolation over 25 dB, operating by 1.0 V single supply with dissipation current of 6.8 mA at 880 MHz. At 1.9 GHz, the IC also showed excellent RF characteristics with dissipation current of 6.5 mA at 1.0 V. The IC die is very small the size is 0.75 mm0.75 mm, and is molded in a mini-6pin plastic package.

Pilot symbol-assisted (PSA) decision-directed coherent adaptive array diversity (CAAD) is proposed for increasing the reverse link capacity of DS-CDMA mobile radio systems. In the proposed scheme, PSA channel estimation is applied to coherent Rake combining, and the weights of the antenna array are adaptively updated using both pilot symbols and decision-directed data symbols after Rake combining as references for minimum mean squared error (MMSE) criteria. The reverse link capacity of a 3-sectored base station is evaluated by computer simulation when fast transmit power control (TPC) based on singal-to-interference plus backgound noise power ratio (SIR) measurement is applied under nultipath Rayleigh fading environments. It is shown that a 6-element (sector) CAAD receiver can increase the capacity to about 4.2 times that with a single antenna (per sector) receiver when links are interference-limited. The link capacity achievable with the 6-element CAAD receiver is 1.2 times that with a 6-branch antenna diversity reciever with antenna spacing of 10 carrier wavelengths, while significantly reducing the strong interference from high bit rate transmission (high transmit power) users.

The transmission performance of DS-CDMA forward link with orthogonal spreading and Rake combining is evaluated under multipath fading environments. A simple-to-use expression for the conditional instantaneous signal-to-interference plus background noise power ratio (SIR) is derived, assuming an M-finger Rake combiner. Using the derived expression, the forward link SIRs of either orthogonal spreading or random spreading can be conveniently computed. The link performance in terms of the average bit error rate (BER) and capacity (the maximum number of allowable users) is evaluated by a Monte Carlo simulation assuming ideal BPSK data modulation. In frequency selective multipath fading, the orthogonality of the forward link is destroyed to some extent and link performance approaches that of random spreading. The extent of orthogonality destruction depends on the multipath channel power delay profile shape and number of resolved paths (for an exponential profile, it is defined as the number of stronger resolved paths that capture 90% of the total received power); so their influences on the link performance are discussed. Also simulated is the distribution of the BERs in a radio coverage area taking into account the path loss and shadowing to evaluate the link capacity at a certain outage probability.

For the power controlled DS-CDMA reverse link, two important issues must be addressed when using a Rake combiner with a limited path diversity order (defined as the number of resolved paths used for combining): the decrease in link capacity and the increase in peak transmit power. The peak transmit power is an important design parameter of transmit power amplifiers. In this paper, expressions for the achievable capacity and required peak transmit power under an multi-cell environment are developed. Based on the developed expressions, the relative capacity and required peak transmit power are evaluated theoretically and by Monte Carlo simulations under multipath Rayleigh fading environments with uniform and exponential power delay profiles. The effects of Rake based on maximal ratio combining (MRC) and selection combining (SC) are compared. The influence of the power delay profile shapes is also discussed.

In this paper, we consider conventional signaling link fault tolerance and error correction mechanisms to provide reliable services of mobile multimedia telecommunication network based on ATM (Asynchronous Transfer Mode) technology. Also, we propose an efficient signaling protocol interworking architecture and a reliable distributed interworking network architecture between SS7 based FPLMTS and ATM networks. Besides, we evaluate the performance of proposed method through computer simulation. According to the results, proposed signaling architecture shows efficient and fast fault restoration characteristics than conventional MTP-3/3b based network. Functional signaling protocol stack and network architecture of proposed fast rerouting mechanism provide reliable and efficient restoration performance in view of interworking between SS7 based FPLMTS and ATM networks.

In this paper, we propose a scalable service networking architecture as a TINA-like environment for providing flexibly various mobility services. The proposed architecture provides an environment that enables the advent of service providers and rapidly introduces multimedia applications, considering networks scalability. For supporting customized mobility services, this architecture adopts a new service component, which we call Omnipresent Personal Environment Manager (OpeMgr). In order to support mobile users who move between heterogeneous networks, for instance, between the TINA-like environment and the Internet environment, we propose a structure of a gateway. In addition, the proposed architecture uses the fixed and mobile agent approaches for supporting the user's mobility, and we evaluated their performances with comparing those approaches.

This paper describes a mobile information access system based on a multi-agent architecture. With the rapid progress of wireless data communications, mobile Internet access will be more and more popular. In mobile environments, user location plays an important role for information filtering and flexible communication service. In this paper, we propose a mobile information service system where a user with a handy terminal accesses Internet in an open air to look up map information and related town information. Each user information is managed by an independent agent process. And the agent provides each user with a personal service collaborating with other applications. A map-based information service example based on this architecture is also described.

A multicast (point-to-multipoint) protocol of a satellite broadcast channel by a source and many destinations is presented and its performance characteristics are analyzed. We propose a new time-domain multicast scheme for packet satellite channels, retransmission via collisions protocol (called RVCP). RVCP is classified to the automatic repeat request (ARQ) of the multi-selective-repeat scheme and does not require individual channels for each receiving station to request for broadcast packets that have been received incorrectly. Our analytical models show that RVCP performs considerably better than the other protocols, particularly in the situation that packet error rate is less than 10-4 or there are a large number of destinations. It is an excellent characteristic of RVCP that the equipment of the source station need not increase in proportion to the number of destinations, too. And since RVCP is a relatively simple protocol, it is easy to be implemented.

Recently, the number of users utilizing mobile communication services has increased greatly in many information and communication fields. In the future, the number of mobile communication system users will increase even faster, until the rate of diffusion ultimately reaches that of telephones. The day that each person has his own portable mobile terminal is not so far off. Moreover, the systems will not only be used as telephones but also as mobile computing for multimedia information. Digitalization technologies of mobile communication systems needed to realize such mobile computing will be introduced in this paper.

This paper proposes a protocol to support mobility in the Internet with a new encapsulation technique. IP-squared (IP2). A basic idea to support mobility is as follows; 1) to define two IP addresses for each mobile host that indicate the host itself and its geographical location (logical and geographical identifiers), 2) to maintain an association of the logical identifier with the geographical identifier and 3) to continue communications between hosts by converting their logical identifiers to the corresponding geographical identifiers dynamically wherever they migrate. The association is called mobility binding. A goal of IP2 is to propose a mobility support feature which can simultaneously realize efficient routing paths to mobile hosts and less control traffics to maintain the mobility bindings into the current Internet Protocol without any modifications to both the conventional protocols and nodes. IP2 forms the efficient routing paths by enabling intermediate nodes to process the encapsulated datagrams. The key technique for this feature is a new header detection algorithm based on CRC checksum calculation and an effective usage of a header structure. Percentage of efficient routing paths can be adaptively controlled, depending on dispositions of the nodes which can en -and de capsulate datagrams appropriately based on the detection algorithm and the mobility bindings. The mobility binding must be updated whenever a mobile host migrates to another network. IP2 adopts an updating scheme combining self refreshment and on demand updating modes with taking a mechanism to form the efficient routing paths into considerations. It is shown that IP2 can acheive both an efficient routing path formation and a low traffic for mobility binding maintenance through analytical evaluations.

Many network protocols for routing messages have been proposed for mobile computing environments. In this paper, we consider the query processing strategy which operates over these network protocols. To begin with, we introduce five fundamental location update methods based on ideas extracted from the representative network protocols. They are the single broadcast notification (SBN), the double broadcast notification (WBN), the single default notification (SDN), the double default notification (WDN), and the no notification (NN). As a network protocol, each method is strong in performance in some system enrivonment, but weak in others. In practical situations, where various kinds of applications are used for various purposes, however, it is required to use a single method. We therefore propose an adaptive query processing strategy where these five location update methods can be dynamically selected. Moreover, we analyze the performance of this adaptive query processing strategy via the Markov chain. We also use the statistical approach to estimate the traffic of individual hosts. Finally, we show the efficiency of our proposed strategy over a wide area of system environments.

Next generation hand-held devices must provide seamless connectivity while obeying stringent power and size constrains. In this paper we examine this issue from the point of view of the Network Interface (NI). We measure the power usage of two PDAs, the Apple Newton Messagepad and Sony Magic Link, and four NIs, the Metricom Ricochet Wireless Modem, the AT&T Wavelan operating at 915 MHz and 2.4 GHz, and the IBM Infrared Wireless LAN Adapter. These measurements clearly indicate that the power drained by the network interface constitutes a large fraction of the total power used by the PDA. We then examine two classes of optimizations that can be used to reduce network interface energy consumption on these divices: transport-level strategies and application-level strategies. Simulation experiments of transport-level strategies show that the dominant cost comes not from the number of packets sent or received by a particular transport protocol but the amount of time that the NI is in an active but idle state. Simulation experiments of application-level strategies that significant energy savings can be made with a minimum of user-visible latency.