For actual multi-channel differential signaling system, the ideal balance or symmetrical topology cannot be established, and hence, an imbalance component is excited. However a theoretical analysis method of evaluating the voltage and current distribution on the differential-paired lines, which allows to anticipate EM radiation at the design stage and to study possible means for suppressing imbalance components, has not been implemented. To provide the basic considerations for electromagnetic (EM) radiation from practical asymmetrical differential-paired lines structure with equi-length routing used in high-speed board design, this paper newly proposes an analytical method for evaluating the voltage and current at any point on differential-paired lines by expressing the differential paired-lines with an equivalent source circuit and an equivalent load circuit. The proposed method can predict S-parameters, distributions of voltage and current and EM radiation with sufficient accuracy. In addition, the proposed method provides enough flexibility for different geometric parameters and can be used to develop physical insights and design guidelines. This study has successfully established a basic method to effectively predict signal integrity and EM interference issues on a differential-paired lines.

We propose a novel short-range wireless communications technology that uses quasi-static electric fields; it enables data communication between devices separated by up to 10 cm via dielectric media at a speed of 10 Mbps. It is considered to be a secure wireless technology since communication area is restricted to below about 10 cm. To suppress electromagnetic radiation, we adopted a baseband transmission scheme in which the quasi-static electric field is directly modulated by 10 BASE-T data signals. Since the spectra of the data signals are concentrated to below 20 MHz, the amplitude of the electric field rapidly decreases outside the communication area. This contributes to enhancing security of the communications system. In this paper, we explain a basic principle of the short-range wireless communications technology. Since baseband data signals are carried by the quasi-static electric field, the quality of the communication is easily degraded by the existence of the earth ground. To isolate the communications system from the earth ground, we introduce a novel electro-optic sensor to receive the quasi-static electric field. With the electro-optic sensor, stable data communication is possible at 10 Mbps via dielectric materials, such as a wooden table.

The peak SAR values of two-element array antennas for mobile handsets in the vicinity of a spherical phantom of a human head are evaluated numerically as a function of the distance between the array antenna and the head phantom when the two elements of a two-element array antenna are either co-phase voltage-fed or reverse-phase voltage-fed. It is found that relation between the worst case of the SAR and the phase difference of array elements strongly depends on the distance. When part of the head phantom is located in the reactive near-field region of the array antenna, although the co-phase feed SAR value is slightly smaller than the reverse-phase feed SAR value, the SAR value is practically independent of the phase difference, but when the head is completely outside the reactive near-field region, the co-phase feed SAR value is larger than the reverse-phase feed SAR value.

To provide basic considerations for the realization of methods for predicting the electromagnetic (EM) radiation from a printed circuit board (PCB) with plural signal traces driven in the even-mode, the characteristics of the EM radiation resulting from two signal traces on a PCB are investigated experimentally and by numerical modeling. First, the frequency responses of common-mode (CM) current and far-electric field as electromagnetic interference (EMI) are discussed. As the two traces are moved closer to the PCB edge, CM current and far-electric field increase. The frequency responses in the two signal trace case can be identified using insights gained from the single trace case. Second, to understand the details of the increase in CM current, the distribution of the current density on the ground plane is calculated and discussed. Although crosstalk ensues, the rule for PCB design is to keep two high-speed traces on the interior of the PCB whenever possible, from the point of view of EM radiation. Finally, an empirical formula to quantify the relationship between the positions of two traces and CM current is provided and discussed by comparing four different models. Results calculated with the empirical formula and finite-difference time-domain (FDTD) modeling are in good agreement, which indicates the empirical formula may be useful for developing EMI design guidelines.

Unwanted electromagnetic emission occurs due to the common-mode current on the cables entering a PC's metal enclosure and can be treated as wire antennas passing through the apertures of the enclosure. To reduce the emission, a stack of metal rings is suggested to be placed around the cable and external to the aperture, adopting the concept of a Coaxial Band-Stop Filter, for the first time. The influence of this novel structure on the common-mode current is examined in the FDTD-method frame work.

It has been demonstrated that a common-mode (CM) current can dominate the EMI processes up to 1 GHz, despite the fact that a CM current is smaller than a differential-mode (DM) current. However, this description is insufficient to describe behavior above 1 GHz. In this paper, the correspondence of CM and DM components for total electromagnetic (EM) radiation from a printed circuit board (PCB) with surface microstrip line, which is commonly used in microwave integrated circuits, at gigahertz frequency is studied experimentally and with finite-difference time-domain (FDTD) modeling. In order to characterize the EM radiation, the frequency response of the CM current, the electric field near the PCB, and the electric far field are investigated. First, the frequency response of the CM current, near and far-fields for the PCB with an attached feed cable are compared up to 5 GHz. Although the CM current decreases above a few gigahertz, near and far electric fields increase as the frequency becomes higher. Second, in order to distinguish between CM and DM radiation at high frequency, the frequency response and the angle pattern of the far-field from a PCB without the feed cable are discussed. The results show that radiation up to 1 GHz is related to the CM component. However, depending on polarization and PCB geometry, radiation may be dominated by the DM rather than the CM component. The results indicate that the DM component may be more significant relative to the CM component, and the increase in EM radiation can not be predicted from only the frequency response of CM current. Therefore, identifying the dominant component is essential for suppressing the EM radiation. This study is a basic consideration to realize a technique which is effective on the suppression of the EM radiation from the PCB with an attached feed cable.

As a new material, silver (Ag) coated fabric has been developed, and its use for shielding electromagnetic radiation is expected. In this paper, seven kinds of Ag coated fabrics, woven, knitted and nonwoven by Ag coated fibers, are prepared, and placed over a PCB with a microstrip line, which is used as a noise source. By measuring the input impedance of the microstrip line, the distance between the PCB and the fabric is fixed to 8 mm to reduce the coupling paths. The shielding effect SE of those fabrics was compared by measuring the magnetic near-field with a small shielded-loop probe. In the results, the resonance frequency is dependent on the fabric's length, as well as the case of a copper sheet. Comparing the texture, the SE of woven and nonwoven fabrics is larger than the knitted fabric. Comparing with the copper sheet, the SE of the fabrics is smaller below 200 MHz, but elsewhere is almost the same.

This paper presents a framework for modeling and mixed-mode simulation of circuits/interconnects and electromagnetic (EM-) radiations. The proposed framework investigates the signal integrity in VLSI chips, packages and wiring boards at the GHz-band level, and verifies the electromagnetic interference (EMI) and the electromagnetic compatibility (EMC) of high-speed systems. In our framework, the frequency characteristics of interconnects and EM-radiations are extracted by the full-wave FDTD simulation. The macromodels of interconnects are synthesized as SPICE subcircuits, and the impulse responses of EM-radiations are stored in the database. Once the macromodels are synthesized, the circuit simulation with the consideration of EM-effects can be performed by using SPICE. The EM-field distributions can be also easily calculated by taking convolutions of pre-simulated EM impulse responses and the SPICE results.

We have developed a signal processing method that is appropriate for detecting electromagnetic radiation due to earthquake activities. The radiation is usually accompanied by a background noise that is mainly caused by atmospheric discharges in the tropical regions. Data representing the seismic radiation is presented as sound via the concept of sonification. This is useful for immediately finding out anomalous seismic radiations, which are often followed by a disastrous earthquake, from the massive data collected from over forty observation stations. It is illustrated that the auditory display is valuable for future earthquake prediction systems.

Radiation properties of magnetic noise from the harness wires of a spacecraft (GEOTAIL) have been studied experimentally and theoretically. A simulation experiment on the noise radiation using a minimum set of subsystems of the spacecraft has shown that the intensity and the directional patterns of the noise radiation from the wires were largely changed by the existence of a conductive plate near the harness wires. The change in the noise characteristics is explained by eddy currents induced in the conductive plate by the signal current flowing in the wires. The eddy currents distributed in the conductive plate were calculated by the Finite Element analysis Method (FEM). The magnetic flux densities calculated from both the source signal current and its induced eddy currents for the wiring configuration of the simulation experiment have shown to be consistent with the values obtained in the experiment. The results in the present study have provided us an important information on a wiring method to diminish noise radiation from harness wires.