We observed dynamical carrier motion in an OLED device under an external reverse bias application using ExTDR measurement. The rectangular wave pulses were used in our ExTDR to observe the transient impedance of the OLED sample. The falling edge of the transmission waveform reflects the transient impedance after applying pulse voltage during the pulse width. The observed pulse width variation at the falling edge waveform indicates that the frontline of the hole distribution in the hole transport layer was forced to move backward to the ITO electrode.

A unified decision scheme for the classification and localization of cable faults is proposed based on a two-step procedure. Having basis in the time domain reflectometry (TDR), the proposed scheme is capable of determining not only the locations but also types of faults in a cable without an excessive additional computational burden compared to other TDR-based schemes. Results from simulation and experiments with measured real data demonstrate that the proposed scheme exhibits a higher rate of correct decision than the conventional schemes in localizing and classifying faults over a wide range of the location of faults.

Mirrored serpentine microstrip lines are proposed for a parallel high speed digital signaling to reduce the peak far-end crosstalk (FEXT) voltage. Mirrored serpentine microstrip lines consist of two serpentine microstrip lines, each one equal to a conventional normal serpentine microstrip line. However, one serpentine microstrip line of the mirrored serpentine microstrip lines is flipped in the length direction, and thus, two serpentine microstrip lines face each other. Time domain reflectometry measurements show that the peak FEXT voltage of the mirrored serpentine microstrip lines is reduced by 56.4% of that of conventional microstrip lines and 30.0% of that of conventional normal serpentine microstrip lines.

A self-calibrating per-pin phase adjuster, which does not require any feedback from the slave chip and a multi-phase clock in the master and slave chips, is proposed for a high speed parallel chip-to-chip interface with a source synchronous double data rate (DDR) signaling. It achieves not only per-pin phase adjustment but also 90° phase shift of a strobe signal for a source synchronous DDR signaling. For this self-calibration, the phase adjuster measures and compensates the only relative mismatched delay among channels by utilizing on-chip time-domain reflectometry (TDR). Thus, variable delay lines, finite state machines, and a test signal generator are additionally required for the proposed phase adjuster. In addition, the power-gating receiver is used to reduce the discontinuity effect of the channel including parasitic components of chip package. To verify the proposed self-calibrating per-pin phase adjuster, the transceivers with 16 data, strobe, and clock signals for the interface with a source synchronous DDR signaling were implemented by using a 60 nm 1-poly 3-metal CMOS DRAM process with a 1.5 V supply. Each phase skew between Strobe and 16 Data was corrected within 0.028UI at 1.6-Gb/s data rate in a point-to-point channel.

High-resolution FMCW reflectometry is often realized by sampling the beat signal with a clock signal generated from an auxiliary interferometer. The drawback of this system is that the measurement range is limited to less than half of the optical path difference of the auxiliary interferometer to satisfy the Sampling theorem. We propose and demonstrate a method to extend the measurement range of the system. The clock signal gerenerated from the auxiliary interferometer is electronically frequency-multipled by using a PLL circuit. The measurement range is experimentally extended by a factor of 20 while keeping high spatial resolution, and is theoretically extended by a factor of 128. The advantage of the proposed system is that the optical path difference of the auxiliary interferometer can be kept short, which is very effective for obtaining the stable and low time-jitter clock signal.

We demonstrate a mode-locked fiber laser (MLFL) method for measuring the chromatic dispersion of long transmission fiber. In this method, device under test (DUT) is inserted in the laser cavity, and the chromatic dispersion is measured by the shift of mode-locking frequency when the lasing wavelength is changed. The experimental results of the MLFL method for a 5km-long single-mode fiber had good agreement with the conventional phase-shift method.

We newly propose an optical coherence domain reflectometry for optical subscriber networks with measurement range enhancement. This reflectometry is based on our own technique to synthesize an optical coherence function. An optical switch after a light source generates optical pulses, which select the measuring region, in which one coherence peak is scanned with high spatial resolution. An optical fiber loop delay line including a frequency shifter is placed in a reference-path of the interferometer. In this method, the measuring region could be easily changed by the hetelodyne intermediate frequency selected at the electronic band pass filter. In the basic experiments, the reflections at 5 km distance are measured with a spatial resolution of 8 cm, and the change of the measuring region is successfully demonstrated.

We describe FMCW reflectometry for characterization of long optical fibers by using an external-cavity laser diode as a light source. Since the optical path difference between the reference beam and the reflected beam from the optical fiber under test is much longer than the coherence length of the light source, the reference and the reflected beams are phase-decorrelated. As a result, the beat spectrum between the reference and the reflected beams is measured. In the phase-decorrelated FMCW reflectomety, the spatial resolution is enhanced by narrowing the spectral linewidth of the light source and increasing the repetition frequency of the optical frequency sweep as well as increasing the chirping range of the optical frequency sweep. In the experiments, an external-cavity DFB laser is used as a narrow linewidth light source, and the optical frequency is swept by minute modulation of the external cavity length. Long single mode optical fibers are characterized, and the maximum measurement range of 80 km is achieved, and the spatial resolutions of 46 m, 100 m and 2 km are achieved at 5 km, 11 km and 80 km distant, respectively. The Rayleigh backscattering is clearly measured and the propagation loss of optical fiber is also measured. The optical gain of an erbium-doped optical fiber amplifier (EDFA) is also estimated from the change in the Rayleigh backscattering level in the optical fiber followed after the EDFA.

A photonic/video hybrid system for optical information processing by synthesis of the coherence function is proposed. Optical coherence function can be synthesized to have delta-function-like shape or notch shape by using direct frequency modulation of a laser diode with an appropriate waveform. Therefore, by choosing only the interference component in the interferometer, information processing functions can be obtained. The photonic/video hybrid system proposed provides a novel way to choose the interference component, which can improve the spatial resolution compared with our previous system with holographic technique. Selective extraction two-dimensional (2-D) information from a three-dimensional (3-D) object is successfully performed in basic experiments.

We propose and demonstrate an excellent linearly frequency-swept laser diode (LD) for sensing system utilizing frequency-moduleted continuous-wave (FMCW) technique. In order to linearly sweep the optical frequency, we adopt a reference interferometer and an electric phase comparator. The interference beat signal of the reference interferometer is phase-compared with an external reference rectangular signal having a fixed frequency near the interference beat signal frequency by a lock-in amplifier. The error signal from the lock-in amplifier is fed back to the modulating signal of the injection current of the LD. Thus, a phase-locked loop composed of optical and electric circuits can be established, and the beat signal frequency is locked to the frequency of the reference signal. The optical frequency of the LD is, therefore, excellently linearly swept in time. In order to experimentally confirm the linearlity of the proposed method, we apply this light source to the FMCW reflectometry. Resultingly, the improvement of the linearity is estimated to be about 10 dB. And the theoretically limited spatial resolution of the FMCW reflectometry is achieved.

This paper proposes a surveillance system concept, which includes the analysis of fiber fault factors and monitored items, the architecture for diagnosing fiber degradation and the system configuration. Fiber faults are classified into two types. One is fiber failure caused by fiber axial tensile strain and the other is fiber loss increase caused by fiber bending and the absorption of hydrogen molecules. It was found that there is an urgent need for fiber axial strain monitoring, sensitive loss monitoring operating at longer wavelengths and water sensing, in order to detect the origin and early indications of these faults before the service is affected. Moreover, an algorithm for predicting and diagnosing fiber faults based on the detected results was investigated and systematized.