This paper investigates primary signal detection by using a quiet period (QP) in cognitive wireless communications. In particular, we provide an analytical model for studying the impact of QPs on the system performance. Our analysis shows that two successive QPs have a significant impact on system performance. Moreover, the analytical results obtained reveal an optimum period of two successive QPs that maximize system performance.

This paper addresses the coexistence issue of distributed heterogeneous networks where the network nodes are cognitive radio terminals. These nodes, operating as secondary users (SUs), might interfere with primary users (PUs) who are licensed to use a given frequency band. Further, due to the lack of coordination and the dissimilarity of the radio access technologies (RATs) among these wireless nodes, they might interfere with each other. To solve this coexistence problem, we propose an architecture that enables coordination among the distributed nodes. The architecture provides coexistence solutions and sends reconfiguration commands to SU networks. As an example, time sharing is considered as a solution. Further, the time slot allocation ratios and transmit powers are parameters encapsulated in the reconfiguration commands. The performance of the proposed scheme is evaluated in terms of the coexistence between PUs and SUs, as well as the coexistence among SUs. The former addresses the interference from SUs to PUs, whereas the latter addresses the sharing of an identified spectrum opportunity among heterogeneous SU networks for achieving an efficient spectrum usage. In this study, we first introduce a new parameter named as quality of coexistence (QoC), which is defined as the ratio between the quality of SU transmissions and the negative interference to PUs. In this study we assume that the SUs have multiple antennas and employ fixed transmit power control (fixed-TPC). By using the approximation to the distribution of a weighted sum of chi-square random variables (RVs), we develop an analytical model for the time slot allocation among SU networks. Using this analytical model, we obtain the optimal time slot allocation ratios as well as transmit powers of the SU networks by maximizing the QoC. This leads to an efficient spectrum usage among SUs and a minimized negative influence to the PUs. Results show that in a particular scenario the QoC can be increased by 30%.

We have been investigating an orthogonal frequency division multiple access (OFDMA) based cellular system that is called "dynamic parameter controlled orthogonal frequency and time division multiple access (DPC-OF/TDMA)" for the development of beyond third generation (B3G) mobile communication systems. Moreover, we have already proposed a time alignment control (TAC) to compensate propagation delays that induce a multiple-access interference (MAI) in the uplink OFDMA. However, that TAC includes a large amount of computations. This means that it is quite difficult for the OFDMA systems to implement TAC into volume-limited hardware devices such as field programmable gate array (FPGA). Thus, we propose a new complexity-reduced TAC (CRTAC) in this paper. CRTAC can be implemented into such devices easily. In this paper, we show some computer simulation results, and then evaluate the error rate performances of DPC-OF/TDMA employing CRTAC. Moreover, we also show the benefit of the reasonable level of the implementation complexity made by CRTAC.

In-band full-duplex (IBFD) has been an attractive technology, which can theoretically double the spectral efficiency. However, when performing IBFD in the dynamic-duplex cellular (DDC) system, inter-user interference (IUI) deteriorates transmission performance in downlink (DL) communication and limits IBFD-applicable area and IBFD application ratio. In this paper, to expand the IBFD-applicable area and improve the IBFD application ratio, we propose an IUI reduction scheme using successive interference cancellation (SIC) for the DDC system. SIC can utilize the power difference and reduce the signal with the higher power. The effectiveness of the proposed scheme is evaluated by the computer simulation. The IUI reducing effect on the IBFD-inapplicable area is confirmed when the received power of the IUI is stronger than that of the desired signal at the user equipment for DL (DL-UE). The IBFD-inapplicable area within 95m from the DL-UE, where the IBFD does not work without the proposed scheme, can reduce by 43.6% from 52.8% to 9.2% by applying the proposed scheme. Moreover, the IBFD application ratio can improve by 24.6% from 69.5% to 94.1%.

In AMS/OFDM systems, base station is in control of the modulation level of each subcarrier, and then, adaptive modulated packet is transmitted from the base station to the mobile station. In this case, the mobile station is required the modulation level information (MLI) to demodulate the received packet. The MLI is generally transmitted as a data symbol, therefore, the throughput is degraded. In an OFDM, the channel response at a particular subcarrier frequency is not supposed to be totally different from its neighboring frequencies, and hence, they must have correlation which depends on the coherence bandwidth of the channel Bc. If we could assign the same modulation level for coherently faded subcarrier block, MLI is required only one time for each subcarrier block. Moreover, we can assign the data on the empty space of pilot signals for increasing the total transmission. In this paper, we propose an adaptive subcarrier block modulation with differentially modulated pilot symbol assistance for downlink OFDM using uplink delay spread.

To connect among many radio base stations by using optical fiber bus link in microcellular system, subcarrier multiplexing (SCM) is excellent in simplicity and flexibility. But performance degradation due to optical beat noises is severe problem. To solve this problems, this paper proposes a new type of intercell connection bus fiber-optic link (ICBL) using time division multiplexing, called TDM-ICBL. This paper also analyzes transmission performance of TDM-ICBL theoretically and compares with SCM-ICBL. The analysis clarifies that while the number of RBSs connected to SCM-ICBL is severely restricted by beat noises, TDM-ICBL is more useful than SCM-ICBL when there are many number of connected RBSs.

This paper proposes out-of-band emission reduction schemes for IEEE 802.11af based Wireless Local Area Network (WLAN) systems operating in TV White Spaces (TVWS). IEEE 802.11af adopts Orthogonal Frequency Division Multiplexing (OFDM) to exploit the TVWS spectrum effectively. The combination of the OFDM and TVWS may be able to solve the problem of frequency depletion. However the TVWS transmitter must satisfy a strict transmission spectrum mask and reduce out-of-band emission to protect the primary users. The digital convolution filter is one way of reducing the out-of-band emission. Unfortunately, implementing a strict mask needs a large number of filter taps, which causes high implementation complexity. Time-domain windowing is another effective approach. This scheme reduces out-of-band emission with low complexity but at the price of shortening the effective guard interval. This paper proposes a mechanism that jointly uses these two schemes for out-of-band emission reduction. Moreover, the appropriate windowing duration design is proposed in terms of both the out-of-band emission suppression and throughput performance for all mandatory mode of IEEE 802.11af system. The proposed time-domain windowing design reduces the number of multiplier by 96.5%.

The conventional successive adaptive loading algorithm, represented by Hughes-Hartogs algorithm, can be used to reduce the transmit power of orthogonal frequency division multiplexing (OFDM) system. However, two major disadvantages exist for this kind of algorithm: One is the long loading time delay caused by the bit-to-bit loading, i.e., only one bit is loaded in every iteration; the other is that there is no flexibility in freely pre-defining the candidate modulation set before the loading is finished. In order to solve these problems, we propose the low-loading-delay parallel adaptive loading algorithms aiming at reducing the transmit power under the condition that the data throughput and error rate are maintained to target values. Two improvements are achieved by the new algorithm. One is that it divides the successive adaptive loading into several independent small-scale loading (SS-Loading) procedures. "SS-Loading" can be performed in parallel mode. To support this, we propose two subband division methods (successive and sorted subband divisions). The simulation results show that for a large range of subband number (1-128), the loading time delay can be remarkably decreased (especially for the parallel adaptive loading based on sorted subband division, i.e., SRT parallel adaptive loading algorithm) with neglectable power efficiency loss, compared with Hughes-Hartogs algorithm. The second improvement is that the new algorithm allows us to pre-define the candidate modulation set, which provide flexibility for the system design, e.g. we can exclude those rarely used modulation modes. We also reveal that Hughes-Hartogs algorithm is actually a special case of the newly proposed algorithm.

In this paper, we propose an IEEE 802.15.10-based layer 2 routing (L2R) method with a load balancing algorithm; the proposal considers fairness in terms of the cumulative number of sending packets at each terminal to resolve the packet concentration problem for the IEEE 802.15.4-based low-power consumption wireless smart utility network (Wi-SUN) systems. The proposal uses the accumulated sending times of each terminal as a weight in calculating each path quality metric (PQM) to decide multi-hopping routes with load balancing in the network. Computer simulation of the mesh network with 256 terminals shows that the proposed routing method can improve the maximum sending ratio (MSR), defined as the ratio of the maximum sending times to the average number of sending times in the network, by 56% with no degradation of the end-to-end communication success ratio (E2E-SR). The proposed algorithm is also experimentally evaluated by using actual Wi-SUN modules. The proposed routing method also improves the MSR by 84% with 70 terminals. Computer simulations and experiments prove the effectiveness of the proposed method in terms of load balancing.

Demand for wireless communication is increasing significantly, but the frequency resources available for wireless communication are quite limited. Currently, various countries are prompting the use of TV white spaces (TVWS). IEEE 802.11 Working Group (WG) has started a Task Group (TG), namely IEEE 802.11af, to develop an international standard for Wireless local Area Networks (WLANs) in TVWS. In order to increase maximum throughput, a channel aggregation mechanism is introduced in the draft standard. In Japan, ISDB-T based area-one-segment broadcasting system (Area-1seg) which is a digital TV broadcast service in limited areas has been permitted to offer actual TVWS services since April 2012. The operation of the IEEE 802.11af system shall not jeopardize the Area-1seg system due to the common operating frequency band. If the Area-1seg partially overlaps with the IEEE 802.11af in some frequency, the IEEE 802.11af cannot use the channel aggregation mechanism due to a lack of channels. As a result, the throughput of the IEEE 802.11af deteriorates. In this paper, the physical layer of IEEE 802.11af D4.0 is introduced briefly, and a partial subcarrier system for IEEE 802.11af is proposed to efficiently use the TVWS spectrum. The IEEE 802.11af co-exist with the Area-1seg by using null subcarriers. Computer simulation shows up to around 70% throughput gain is achieved with the proposed mechanism.

In this study, we construct an analytical model to investigate the system throughput of 802.15.3c WPAN by examining hybrid slotted CSMA/CA-TDMA and slotted CSMA/CA multiple access methods. Our analysis clearly shows the differences between the system throughputs of both multiple access methods. The obtained results show that the hybrid slotted CSMA/CA-TDMA can achieve a considerably higher system throughput compared to the slotted CSMA/CA; the difference between the two access methods is especially pronounced as the increase in the number of devices contending for the network increase. The system throughput comparisons have established why the hybrid slotted CSMA/CA-TDMA is preferred over the slotted CSMA/CA for high-speed wireless communications of the 802.15.3c WPAN.

Interest in the regulatory issues for Software Defined Radio (SDR) is spreading worldwide since the Federal Communications Commission (FCC) recently recognized SDR and created a new category for SDR authorization. SDR technology will bring enormous benefits to the field of wireless services. However, in order to ensure such benefits, revisions of the radio law and/or related ordinances are required regardless of standardization of the software downloading and other implementation details. In order to define the issues peculiar to SDR and to investigate how conformity evaluation should be conducted for radio equipments whose RF characteristics can be altered by software changes in the field, "Study Group on Software Technology for Radio Equipment" was organized by the Telecom Engineering Center (TELEC) in 2000. This paper summarizes a report of the Study Group that was published in March 2003 including the proposal for "Technical regulation conformity evaluation system," the principal output of the study, which proposes how to prevent unauthorized changes to radio equipment in the field.

A flexible symbol-timing synchronization met-hod is a one that uses a common sampling clock to find synchronization points for radio communication systems that have different symbol rates. This method estimates synchronization points from state patterns calculated using the symbol rate, sampling clock, and number of observed symbols. Decreasing the number of state patterns is one of best ways to reduce the amount of device resources needed to store the patterns. In this paper, we propose a new pattern generation method in which the number of generated patterns does not increase when the sampling clocks of the communications systems are different. To show the feasibility of this method for symbol-timing synchronization, we analyzed a relationship between the number of samples and the number of state patterns and calculated the BER (bit error rate) in AWGN (additive white Gaussian noise) and one-path flat Rayleigh fading environments by computer simulation.

This study focuses on system throughput by taking into account the channel interference in IEEE 802.15.3c WPAN, which is based on the hybrid multiple access of CSMA/CA and TDMA, namely CSMA/CA-TDMA. To study the system throughput, we construct a novel analytical model by taking into consideration the channel interference caused by the hidden networks in CSMA/CA-TDMA. The obtained results show that the system throughput achieved by TDMA is highly affected by frame transmission in CSMA/CA. Furthermore, we show that channel interference, which causes a degradation in the system throughput, is a very significant problem in the IEEE 802.15.3c WPAN.

This paper proposes a new subscriber distribution method called FTTA (Fiber To The Area), which uses millimeter-wave radio band to connect subscribers with base station and optical fiber to connect base station with control station in order to obtain broad-band transmission. Usually two main causes of signal degradation, i.e., rainfall attenuation on radio channel and intermodulation distortion on optical channel are considered in this system. Taking into considerations of these two factors, we analyze the available capacity of FTTA system for various 22nQAM modulation levels. The analysis clarifies that there exists an optimum modulation level that can maxize the available capacity, and AGC circuit in the base station is useful to compensate the rainfall attenuation. It is shown that 18.0Gbps is available under the optimum modulation method of the 64QAM with AGC and 12.0Gbps under the 16QAM without AGC when 20 carriers are used.

In this paper, a new configuration method of multimode software radio system by parameter controlled and telecommunication component block embedded digital signal processing hardware (DSPH) is proposed for the future flexible multimedia communications. In this method, in advance, basic telecommunication component blocks are implemented in the DSPH like DSP and FPGA. And, external parameters, which are simple but important information, change the specification of each block. This proposed method has the following features: i) People need to have only one mobile handset and select communication services as they like. ii) The volume of download software is reduced drastically in comparison with conventional full-download-type software radio system. iii) Since important component blocks have already been implemented into the DSPH except for some external parameters in advance, the know-how related to the implementation of DSPH never leak out. In this paper, we evaluate the effectiveness of the proposed configuration method by using computer simulation and developed experimental prototype and comparing with full-download-type software radio system from the viewpoint of the volume of download software. Finally, we introduce several new software radio systems by using the proposed configuration method.

MIMO (multiple-input multiple-output) transmission is a promising technology to improve the frequency usage efficiency in mobile radio communications. In this letter, MIMO transmission with eigenbeam space division multiplexing (E-SDM) is focused on and the site-dependent beamforming characteristics is examined to know the transmission characteristics. Site-dependent radiowave direction of arrival and impulse responses are obtained using ray tracing. Result shows that effect of radiowaves with longer delays is enhanced due to E-SDM beamforming, and rather more capability of treating a longer excess delay is necessary for time-domain multipath compensation.

It is expected that software receivers will be widely available for radio communication, broadcasting and radio monitoring applications because they are able to be equipped with multimode, multirate and multiband functions in a single hardware platform. This paper describes the basic techniques required for software receivers for both hardware and software. The evaluation items and methods were studied and some evaluations done with an experimental software receiver model fabricated for radio monitoring applications. Future concepts in radio communication, broadcasting and radio monitoring applications where software receivers are thought to be suitable, were studied, and problems for realization identified.

Recently, cerebral disease is being a serious problem in an aging society. But, rank evaluation of cerebral disease is not developed and therefore rehabilitation is hard. In this study, we try to assess slight cerebral disease by taking notice of recognition mechanism of face and realizing face image synthesis using computer technology. If we can find a slight cerebral disease and rank evaluation, we can apply to rehabilitation, and a load of medical doctor and patient decreases. We have obtained a result by the experiment, so we report it.

In this paper, the performance of a low duty factor (DF) hybrid direct sequence (DS) multiband (MB)-pulsed ultra wideband (UWB) system is evaluated over realistic propagation channels to highlight its capability of interference mitigation. The interference mitigation techniques incorporated in the DS-MB-UWB system is a novel design that includes the utilization of the frequency-agile multiple sub-band configuration and the coexistence-friendly low DF signaling. The system design consists of a Rake type receiver over multipath and multi-user channel in the presence of a coexisting narrowband interferer. The propagation channels are modeled based on actual measurement data. Firstly, by suppressing the power in the particular sub-band coexisting with the narrowband signal, performance degradation due to narrowband interference can be improved. It is observed that by fully suppressing the sub-band affected by the narrowband signal, a typical 1-digit performance improvement (e.g. BER improves from 10-3 to 10-4) can be achieved. Secondly, by employing lower DF signaling, self interference (SI) and multi-user interference (MUI) can be mitigated. It is found that a typical 3 dB improvement is achieved by reducing the DF from 0.5 to 0.04. Together, the sub-band power suppression and low DF signaling are shown to be effective mitigation techniques against environment with the presence of SI, MUI and narrowband interference.