A novel type of millimeter/submillimeter wave sampler based on resonant tunneling diodes (RTDs) was proposed, and its operation was confirmed by circuit simulation. It consists of an RTD pulse generator and an RTD detector. Owing to the fuse-like nonlinear I-V curve, highly sensitive sampling can be obtained. We also found that the effects of non-ideality in the I-V curve of the RTD can be corrected by sweeping the DC bias for the RTD detector.

Hard-type oscillators for ultrahigh frequency applications were proposed based on resonant tunneling diodes (RTDs) and a HEMT trigger circuit. The hard-type oscillators initiate oscillation only after external excitation. This is advantageous for suppressing the spurious oscillation in the bias line, which is one of the most significant problems in the RTD oscillators. We first investigated a series-connected circuit of a resistor and an RTD for constructing a hard-type oscillator. We carried out circuit simulation using the practical device parameters. It was demonstrated that the stable oscillation can be obtained for such oscillators. Next, we proposed to use series-connected RTDs for the gain block of the hard-type oscillators. The series circuits of RTDs show the negative differential resistance in very narrow regions, or no regions at all, which makes impossible to use such circuits for the conventional soft-type oscillators. However, with the trigger circuit, they can be used for hard-type oscillators. We confirmed the oscillation and the bias stability of these oscillators, and also demonstrated that the voltage swing can be easily increased by increasing the number of RTDs connected in series. This is promising method to overcome the power restriction of the RTD oscillators.

A third order harmonic oscillator has been proposed based on the resonant tunneling diode pair oscillators. This oscillator has significant advantages, good stability of the oscillation frequency against the load impedance change together with capability to output higher frequencies. Proper circuit operation has been demonstrated using circuit simulations. It has been also shown that the output frequency is stable against the load impedance change.

The oscillators based on an active transmission line periodically loaded with RTD pairs are studied using circuit simulation with special attention to the behavior of harmonics. Generation of strong high order harmonic (9th) was observed. This is caused by the frequency locking in the high frequency passband. The harmonic oscillators based on this phenomenon are promising for high performance THz sources.

Frequency delta sigma modulation (FDSM) is a unique analog to digital conversion technique featuring large dynamic range with wide frequency band width. It can be used for high performance digital-output sensors, if the oscillator in the FDSM is replaced by a variable frequency oscillator whose frequency depends on a certain external physical quantity. One of the most important parameters governing the performance of these sensors is a phase noise of the oscillator. The phase noise is an essential error source in the FDSM, and it is quite important for this type of sensors because they use a high frequency oscillator and an extremely large oversampling ratio. In this paper, we will discuss the quantitative effects of the phase noise on the FDSM output on the basis of a simple model. The model was validated with experiments for three types of oscillators.

An important issue in the realization of optical packet-switched (OPS) networks is the resolution of packet contention caused by the lack of RAM-like optical buffering. Although an optical buffer using fiber delay lines (FDLs) has been proposed, its capacity is extremely limited. There have been several studies of this problem. One approach is deflection routing, which is widely used in electronic packet-switched networks or optical burst-switched (OBS) networks. However, in OPS networks, packet lengths are short, so that the speed requirement for route lookup is very stringent. If the network topology is geometric, such as a Manhattan Street Network (MSN), hop-by-hop routing can be implemented by simple optical logic devices without an electronic routing table. However, if the topology is not geometric, it is hard to implement deflection routing electronically or optically. Another approach is reflection routing, which is easy to implement but has a higher probability of packet loss than does deflection routing. In this paper, we propose a packet contention resolution scheme, reflection-based deflection routing, which is based on reflection routing and enables switching the reflected packet to an alternate path if its primary path remains congested. Our method alleviates the time limitation on setting an alternate path by making use of the packet reflection latency and also reduces the probability of packet loss. We evaluate the performance of the proposed method by simulation experiments and show its effectiveness.

High-resolution Direction-of-Arrival (DOA) estimation techniques for antenna arrays have been widely desired in many applications such as smart antennas, RF position location, and RFID system. To realize high-resolution capability of the techniques, precise array calibration is necessary. For an array of single-mode elements, a calibration matrix derived by the open-circuit method is the simplest one. Unfortunately, calibration performance of the method is not enough for the high-reslution DOA estimation techniques. In this paper, we consider problems of the calibration matrix derived by the method, and show that errors in the matrix can be effectively removed by an optimal diagonal weight coefficient. In the proposed compensation technique, the number of newly introduced parameters, or unknowns, is only one for an array of the identical elements. Performance of the simple compensation technique is verified numerically and experimentally.

Super regenerative detectors using a resonant tunneling diode (RTD) were fabricated and investigated for ultra-high frequency detectors. A key point is to use the RTD super regenerative detector for detecting much higher frequencies than the free-running oscillation frequency of the detector. This is possible owing to the superior high frequency characteristics of the RTDs. This has various advantages, such as circuit simplicity, easy design, and low power consumption. Clear detection of 50,GHz signal was demonstrated with a super regenerative detector which has 1.5,GHz free-running frequency. Moreover, detailed experiments revealed that the frequency dependence of the detection efficiency is smooth, and the harmonic frequencies have no effect. This is advantageous for high frequency detection.

A hard-type oscillator is defined as an oscillator having stable fixed points within a stable limit cycle. For resonant tunneling diode (RTD) oscillators, using hard-type configuration has a significant advantage that it can suppress spurious oscillations in a bias line. We have fabricated hard-type oscillators using an InGaAs-based RTD, and demonstrated a proper operation. Furthermore, the oscillating properties have been compared with a soft-type oscillator having a same parameters. It has been demonstrated that the same level of the phase noise can be obtained with a much smaller power consumption of approximately 1/20.

We achieved detailed characterization of resonant tunneling chaos generator circuits in microwave frequency range. The circuit is analogous to Duffing oscillator, where the third-order nonlinear potential term is emulated by the nonlinear current-voltage curve of the resonant tunneling diode. The circuit includes a periodic reset mechanism to output identical chaos signal, which is essential to observe chaos signal on a sampling oscilloscope. Though this was shown to be effective in our previous papers, the length of the waveforms to observe is limited to rather short period, and it was unclear if this technique can be used for detailed characterization of such high-frequency chaos. In this paper, we improved the circuit design to observe longer waveforms, and demonstrated that the detailed characterization is possible using this periodic resetting technique with a sampling oscilloscope. The hybrid integration scheme is also used in this paper, which allows the easiest and shortest way to mimic a circuit as per circuit design, and precise estimation of circuit parameters aiming to eliminate circuit-related abnormalities. We provide deep insight into the dynamics associated with our circuit, starting from the single period, double period, chaos, and triple period regimes, by extracting power spectra, return maps, phase portraits, and bifurcation diagrams from acquired time series using sampling oscilloscope. Our method to study microwave chaotic signals can be applied to much higher frequency ranges, such as THz frequency range.

A novel displacement sensor was proposed based on a frequency delta-sigma modulator (FDSM) employing a microwave oscillator. To demonstrate basic operation, we fabricated a stylus surface profiler using a cylindrical cavity resonator, where one end of the cavity is replaced by a thin metal diaphragm with a stylus probe tip. Good surface profile was successfully obtained with this device. A 10 nm depth trench was clearly observed together with a 10 µm trench in a single scan without gain control. This result clearly demonstrates an extremely wide dynamic range of the FDSM displacement sensors.