A novel method for measuring microwave reflection coefficients without the open and load standards is proposed. In this method, a single probe is inserted into an air line and the output wave is detected by a vector detector. Offset shorts are used for the calibration. The measurement system is constructed using 7 mm coaxial line and APC7 connectors. The result of the measurement in the frequency range 1-9 GHz shows the possibility of the proposed method. All the major systematic errors can be estimated from the data that is easily obtainable.

The transmission S-parameter, S21, between dipole elements on a rectangular finite ground plane is calculated by the MoM with planar-segments in the horizontally and vertically polarized configurations. Supposed a 1/10 scaling, the frequency range is selected 0.15-0.8 GHz. The size of the finite ground plane is 40 cm 100 cm. The dipole-element length is 18.8 cm (half-wavelength at 0.8 GHz). The distance between dipole elements is 30 cm. The results are compared to the calculated results with the conventional MoM-GTD hybrid method and also the measured results with a TRL-calibrated network analyzer. It makes clear that the MoM-GTD hybrid method is not applicable to a small ground plane in the vertically polarized configuration. The results calculated by the MoM with planar-segments agree well to the measured results both in the horizontal and vertical polarizations. The results show that the size of the finite ground plane for the vertical polarization should be much larger than for the horizontal polarization.

In this paper, a method for finding the direction of arrival (DOA) of a single short pulse is proposed. The method is based on a waveform reconstruction technique using complex antenna factors (CAF). Since the frequency characteristics of CAF has angle dependency, the DOA of an electromagnetic pulse can be determined by the waveforms reconstructed with CAF. The results of a simulation and an experiment show the possibility to apply the two-dimensional DOA finding.

This letter presents the characteristics of complex antenna factors of a resistor loaded dipole antenna with a balun consisting of two coaxial feeders (coaxial cable balun). The resistor loading is used to realize dipole antennas with higher fidelity than unloaded dipole equivalents. The complex antenna factor for a resistor loaded dipole antenna with coaxial cable balun is derived by extending the power loss concepts. The numerical results show that the series resistor loaded dipole antenna offers higher fidelity than the unloaded dipole. The result of the calculated complex antenna factors are in good agreement with that of the measured results.

In order to calibrate fiber optic reflectoreters accurately, the imperfection of a high-reflection standard of which power reflection coefficient is close to unity has been estimated. The power reflection coefficient of 0.98 has been attained.

The antenna factor measurement of the dipole antennas for electromagnetic interference (EMI) measurements is studied theoretically and experimentally. The 3-antenna method is applied to near-field. Near-field transmission characteristics between the transmitting and receiving dipole antennas is obtained by using the electromotive force (EMF) method, where sinusoidal current distributions are assumed. It is shown that the antenna factors can be measured from transmission values between two antennas and near-field correction factors at any height of each antenna.

The charge neutralized at a small gap discharge has been evaluated from measured electromagnetic fields by two methods. The small gap discharges simulate ESD events. The evaluated charge decreases rapidly as a step shape immediately in a moment of the discharge. The accumulated static charge and the risetime of the neutralization step increase with the gap length. When the gap length is 0.1mm, risetime and the initial static charge are about 0.3ns and 5.6nC, respectively.

The wave forms of electric and magnetic fields radiated by short gap discharges are measured to analyze electrostatic discharge (ESD) events in the near-field zone with the monopole antennas, the loop antenna and the 5.5GHz bandwidth waveform digitizer. The antenna outputs are corrected by the measured characteristics of the antennas. The relations between the measured electric field and the discharge currents are discussed.

Nowadays, open source software (OSS) systems are adopted by proprietary software projects. To reduce the risk of using problematic OSS systems (e.g., causing system crashes), it is important for proprietary software projects to assess OSS systems in advance. Therefore, OSS quality assessment models are studied to obtain information regarding the quality of OSS systems. Although the OSS quality assessment models are partially validated using a small number of case studies, to the best of our knowledge, there are few studies that empirically report how industrial projects actually use OSS quality assessment models in their own development process. In this study, we empirically evaluate the cost and effectiveness of OSS quality assessment models at Fujitsu Kyushu Network Technologies Limited (Fujitsu QNET). To conduct the empirical study, we collect datasets from (a) 120 OSS projects that Fujitsu QNET's projects actually used and (b) 10 problematic OSS projects that caused major problems in the projects. We find that (1) it takes average and median times of 51 and 49 minutes, respectively, to gather all assessment metrics per OSS project and (2) there is a possibility that we can filter problematic OSS systems by using the threshold derived from a pool of assessment metrics. Fujitsu QNET's developers agree that our results lead to improvements in Fujitsu QNET's OSS assessment process. We believe that our work significantly contributes to the empirical knowledge about applying OSS assessment techniques to industrial projects.

This paper reviews recent developments in small-sized broadband antennas for EMI measurements, especially in the microwave frequency region. Transient EMI measurements are also discussed by introducing complex antenna factors and conversion of frequency-domain data into time-domain data. This paper also focuses on considerable improvements achieved in calibration techniques for conventional EMI antennas in VHF/UHF bands.

A novel method for image reconstruction of a microwave hologram synthesized from one-dimensional data is proposed. In the data acquisition, an emitting antenna is shifted along a line. At every position of the emitting antenna, the amplitude and phase of diffraction fields are measured with a detecting antenna along a line perpendicular to the shifted direction. An equivalent two-dimensional diffraction field is synthesized from the one-dimensional data sets. The conventional reconstruction method applied to the one-dimensional configuration was the Fresnel approximation method. In this paper, an equivalent diffraction is introduced in order to obtain better images than the Fresnel approximation. An experiment made at 10 GHz shows the usefulness of the proposed method.

The transmission S-parameter between two dipole-elements is a measure to evaluate sites for measuring complex antenna factors (CAF). In this paper, the S-parameter between two dipole-elements on a ground plane is measured using a network analyzer with its TRL (Thru-Reflect-Line) calibration. The S-parameter is also calculated by the method of moment (MoM) and compared to the measurement results. The comparison shows that the calculated S-parameter is usable as a reference value in the evaluation of CAF measurement sites. As an example of the evaluation and selection of measurement sites, the transmission S-parameter on a finite ground plane is calculated using the hybrid method combined the geometrical theory of diffraction (GTD) and MoM. As a result, a preferable antenna setting on the finite ground plane is recommended.