In this study, we propose a cooperative sensing with distributed pre-detection for gathering sensing information on shared primary system. We have proposed a system that gathers multiple sensing information by using the orthogonal narrowband signal; the system is called the orthogonal frequency-based sensing information gathering (OF-SIG) method. By using this method, sensing information from multiple secondary nodes can be gathered from the surrounding secondary nodes simultaneously by using the orthogonal narrowband signals. The advantage of this method is that the interference from each node is small because a narrowband tone signal is transmitted from each node. Therefore, if appropriate power and transmission control are applied at the surrounding nodes, the sensing information can be gathered in the same spectrum as the primary system. To avoid interference with the primary receiver, we propose a cooperative sensing with distributed pre-detection for gathering sensing information in each node by limiting sensing node power. In the proposed method, the number of sensing information transmitting nodes depends on the pre-detection ability of the individual sensing at each node. Then the secondary node can increase the transmit power by improving the sensing detection ability, and the secondary node can gather the sensing information from the surrounding secondary nodes which are located more far by redesign the transmit power of the secondary nodes. Here, we design the secondary transmit power based on OF-SIG while considering the aggregated interference from multiple sensing nodes and individual sensing ability. Finally we confirm the performance of the cooperative sensing of the proposed method through computer simulation.

In this paper, we introduce a distributed power allocation strategy for random access, that has the capabilities of multipacket reception (MPR) and successive interference cancellation (SIC). The proposed random access scheme is suitable for machine-to-machine (M2M) communication application in fifth-generation (5G) cellular networks. A previous study optimized the probability distribution for discrete transmission power levels, with implicit limitations on the successful decoding of at most two packets from a single collision. We formulate the optimization problem for the general case, where a base station can decode multiple packets from a single collision, and this depends only on the signal-to-interference-plus-noise ratio (SINR). We also propose a feasible suboptimal iterative per-level optimization process; we do this by introducing relationships among the different discrete power levels. Compared with the conventional power allocation scheme with MPR and SIC, our method significantly improves the system throughput; this is confirmed by computer simulations.

Recently, the growing concepts that information communication technologies apply to social infrastructures have caused deep interests with wireless sensor networks (WSNs). WSNs can be used for various application areas such as home, health, factory and so on. For the different application areas, there are different technical issues (e.g., security, reliability, real time gathering, long life time, scalability). Efficient information gathering can be potentially obtained if we take a suitable information gathering method with considering the requirements of each WSN application. Thus, we have not persisted all information gathering perfectly and have proposed one of simple information gathering methods in response to the requirements of WSN applications in this paper. In the proposed method, the information is converted to physical-layer parameters of wireless communications, such as frequency and time. Also, simulations are performed to validate the effectiveness of the proposed method in real time gathering and estimating with high precision.

In this paper, we propose a novel highly reliable packet transmission protocol for ad-hoc wireless networks without deciding the route from a source node to a destination node in advance. The proposed protocol uses distributed surrounding nodes as transmitters of the retransmission packet when the transmitted packet contains an error. In this protocol, when a packet is not correctly received at the destination node, the source node and the surrounding nodes that have correctly received the packet simultaneously retransmit the same data packet to the destination node. The transmitting timing is triggered by the control packet transmitted from the source node. These operations are repeated until the packet reaches to the destination node like automatic repeat request (ARQ). Moreover, the retransmitted packet is encoded by one branch of the space time block code (STBC) for improving the performance with the network diversity effect. We call this method as STBC Distributed ARQ scheme. The performance of the proposed scheme is evaluated by the computer simulations.

This paper provides theoretical analyses for maximum cyclic autocorrelation selection (MCAS)-based spectrum sensing techniques in cognitive radio networks. The MCAS-based spectrum sensing techniques are low computational complexity spectrum sensing in comparison with some cyclostationary detection. However, MCAS-based spectrum sensing characteristics have never been theoretically derived. In this study, we derive closed form solutions for signal detection probability and false alarm probability for MCAS-based spectrum sensing. The theoretical values are compared with numerical examples, and the values match well with each other.

In this paper, we propose the novel concept of a spectrum database for improving the efficiency of spectrum utilization. In the current design of TV white space spectrum databases, a propagation model is utilized to determine the spectrum availability. However, this propagation model has poor accuracy for radio environment estimation because it requires a large interference margin for the PU coverage area to ensure protection of primary users (PUs); thus, it decreases the spectrum sharing efficiency. The proposed spectrum database consists of radio environment measurement results from sensors on mobile terminals such as vehicles and smart phones. In the proposed database, actual measurements of radio signals are used to estimate radio information regarding PUs. Because the sensors on mobile terminals can gather a large amount of data, accurate propagation information can be obtained, including information regarding propagation loss and shadowing. In this paper, we first introduce the architecture of the proposed spectrum database. Then, we present experimental results for the database construction using actual TV broadcast signals. Additionally, from the evaluation results, we discuss the extent to which the proposed database can mitigate the excess interference margin.

In this paper, we propose a soft decision based cooperative sensing method for cognitive radio (CR) networks for opportunistic frequency usage. To identify unused frequency, CR should exploit sensing technique to detect presence or absence of primary user and use this information to opportunistically provide communication among secondary users while performance of primary user should not be deteriorated by the secondary users. Because of multipath fading or shadowing, the detection of primary users may be significantly difficult. For this problem, cooperative sensing (CS), where gathered observations obtained by multiple secondary users is utilized to achieve higher performance of detection, has been investigated. We design a soft decision based CS analytically and analyze the detector in several situations, i.e., signal model where single-carrier case and multi-carrier case are assumed and two scenarios; in the first scenario, SNR values of secondary users are totally equal and in the second scenario, a certain SNR difference between secondary users is assumed. We present numerical results as follows. The first scenario shows that there is little difference between the signal models in terms of detection performance. The second scenario shows that CS is superior to non-cooperative sensing. In addition, we presents that detection performance of soft decision based CS outperform detection performance of hard decision based CS.

In order to improve the cell boundary throughput performance and to extend the coverage area, relaying transmission with relay stations (RSs) is becoming a promising architecture for the next generation cellular systems. However, if RSs are operated in every cell, the interference between cells increases and the throughput improvement effect with RSs is prone to be restricted. In this paper, we propose a scheme reducing the interference from other cells by using packet transmission control. This packet transmitting control technique is realized by the compound scheduling technique with the Proportional fair (PF) scheduling and the Maximum Carrier-to-Interference power Ratio (Max CIR) scheduling. The proposed scheme can improve the throughput around the cell boundary by controlling the timing of transmission of each cell with appropriate power and user assignment. The simulation results show that the proposed method can also improve the fairness of user throughput and system throughput considering the users of whole cell.

In this paper, a novel fusion center controlled media access control (MAC) protocol for physical wireless parameter conversion sensor networks (PHY-C SN), and a transmission power design for each sensor node are proposed. In PHY-C SN, the sensing information is converted to corresponding subcarrier number of orthogonal frequency division multiplexing (OFDM) signals, and all sensor nodes can send sensing information simultaneously. In most wireless sensor network standards, each sensor node detects the surrounding wireless signal through carrier sense. However, sensor nodes cannot send signals simultaneously if carrier sense is applied in PHY-C SN. Therefore, a protocol for PHY-C SN is devised. In the proposed protocol, the fusion center detects the surrounding wireless environment by carrier sense and requests sensing information transmission toward sensor nodes if no other wireless systems are detected. Once the sensor nodes receive the request signal, they transmit sensing information to the fusion center. Further, to avoid harmful interference with surrounding wireless systems, the transmission power of each sensor is designed to suit the considering communication range and avoid interference toward other wireless systems. The effectiveness of the proposed protocol is evaluated by computer simulation. The parameters for collection like the number of collecting sensor nodes and the radius of the collection area are also examined when determining the transmission power of sensor nodes. Results show that highly efficient information collection with reducing interference both from and towards surrounding wireless systems can be implemented with PHY-C SN.

Spread Spectrum (SS) has been widely used for various wireless systems such as cellular systems, wireless local area network (LAN) and so on. Using multiple antennas at the receiver, two-dimensional (2D) RAKE is realized over the time- and the space-domain. However, it should be noted that the 2D-RAKE receiver must detect the bit timing prior to the RAKE combining. In case of deep fading, it is often difficult to detect it due to low signal-to-noise power ratio (SNR). To solve this problem, we propose a new blind 2D-RAKE receiver based on the constant modulus algorithm (CMA). Since it does not need a priori bit timing detection, it is possible to compensate frequency selective fading even in very low SNR environments. The proposed method is particularly suitable for the software defined radio (SDR) architecture. The performance of the proposed method is investigated through computer simulations.

This paper proposes a MAC protocol for efficient broadcasting in wireless ad hoc networks. Pure flooding leads to serious redundant broadcasts, packet contention and packet collisions, known as the broadcast storm problem. This paper focuses on how to reduce the redundant broadcasts. Several protocols to achieve efficient broadcasting have been proposed. However a trade-off exists between the reachability and the broadcasting ratio, which is the ratio of the number of the broadcasting nodes to the number of received nodes. This paper proposes a new MAC protocol for on-demand broadcasting, which is referred to as dialogue-based protocol in order to resolve the trade-off. The dialogue-based protocol employs additional massages which are called as request packets and reply signals. They are exchanged in an on-demand manner, in order that relay candidate nodes recognize its neighbor nodes status whether they have already received the broadcast packets. Finally, by computer simulations, this paper presents that the dialogue-based scheme combines high reachability with low broadcasting ratio by using the low additional massages.

In this paper, a novel synchronization method is proposed for a heterogeneous cognitive radio that combines public safety mobile communication systems (PMCSs) with commercial mobile wireless communication systems (CMWCSs). The proposed method enables self-synchronization of the PMCSs as well as co-synchronization of PMCSs and CMWCSs. In this paper, the self-synchronization indicates that each system obtains own timing synchronization. The co-synchronization indicates that a system recognizes data transmitted from other systems correctly. In our research, we especially focus on PMCS self-synchronization because it is one of the most difficult parts of our proposed cognitive radio that improves PMCS's communication quality. The proposed method is utilized for systems employing differentially encoded π/4 shift QPSK modulation. The synchronization can be achieved by correlating envelopes calculated from a PMCS's received signals with subsidiary information (SI) sent via a CMWCS. In this paper, the performance of the proposed synchronization method is evaluated by computer simulation. Moreover, because this SI can also be used to improve the bit error rate (BER) of PMCSs, BER improvement and efficient SI sending methods are derived, after which their performance is evaluated.

This paper proposes a novel cooperative scheme combining distributed space-time block code (STBC) at physical layer, multiple access protocol at medium access control (MAC) layer and opportunistic routing without complicated routing algorithm for achieving high reliability for vehicle-to-vehicle (V2V) communications. The proposed scheme can reduce interference and collision, and achieve reducing redundant broadcast of safety-related messages for multi-hop vehicular communications on highway. In particular, we propose a novel algorithm of relay selection based-on position, speed and direction of movement to select intermediate vehicle stations (VS) with high contribution according to the transmission direction. Furthermore, in order to reduce interference and collision, we install a new timer to select a master relay vehicle station (MVS) which manages a packet transmission of whole network to trigger and synchronize transmitting timing of relay VSs (RVSs) in each hop. From the results of simulations, we can confirm that the proposed method can achieve reducing the redundant broadcast safety-related messages with keeping the packet loss probability by limiting the retransmission at each VS.

A multi-channel cognitive radio is a powerful solution for recovering the exhaustion of frequency spectrum resources. In a cognitive radio, although master and slave terminals (which construct a communication link) have the freedom to access arbitrary channels, access channel mismatch is caused. A rendezvous scheme based on frequency hopping can compensate for this mismatch by exchanging control signals through a selected channel in accordance with a certain rule. However, conventional frequency hopping schemes do not consider an access protocol of both control signals in the rendezvous scheme and the signal caused by channel access from other systems. Further, they do not consider an information sharing method to reach a consensus between the master and slave terminals. This paper proposes a modified rendezvous scheme based on learning-based channel occupancy rate (COR) estimation and describes a specific channel-access rule in the slave terminal. On the basis of this rule, the master estimates a channel selected by the slave by considering the average COR of the other systems. Since the master can narrow down the number of channels, a fast rendezvous scheme with a few control signals is established.

Spectrum databases are required to assist the process of radio propagation estimation for spectrum sharing. Especially, a measurement-based spectrum database achieves highly efficient spectrum sharing by storing the observed radio environment information such as the signal power transmitted from a primary user. However, when the average received signal power is calculated in a given square mesh, the bias of the observation locations within the mesh strongly degrades the accuracy of the statistics because of the influence of terrain and buildings. This paper proposes a method for determining the statistics by using mesh clustering. The proposed method clusters the feature vectors of the measured data by using the k-means and Gaussian mixture model methods. Simulation results show that the proposed method can decrease the error between the measured value and the statistically processed value even if only a small amount of data is available in the spectrum database.

In this paper, we propose a novel primary user detection scheme for spectrum sensing in cognitive radio. Inspired by the conventional signal classification approach, the spectrum sensing is translated into a classification problem. On the basis of feature-based classification, the spectral correlation of a second-order cyclostationary analysis is applied as the feature extraction method, whereas a stacked denoising autoencoders network is applied as the classifier. Two training methods for signal detection, interception-based detection and simulation-based detection, are considered, for different prior information and implementation conditions. In an interception-based detection method, inspired by the two-step sensing, we obtain training data from the interception of actual signals after a sophisticated sensing procedure, to achieve detection without priori information. In addition, benefiting from practical training data, this interception-based detection is superior under actual transmission environment conditions. The alternative, a simulation-based detection method utilizes some undisguised parameters of the primary user in the spectrum of interest. Owing to the diversified predetermined training data, simulation-based detection exhibits transcendental robustness against harsh noise environments, although it demands a more complicated classifier network structure. Additionally, for the above-described training methods, we discuss the classifier complexity over implementation conditions and the trade-off between robustness and detection performance. The simulation results show the advantages of the proposed method over conventional spectrum-sensing schemes.

Wireless ad hoc communications such as ad hoc networks have been attracting researchers' attention. They are expected to become a key technology for "ubiquitous" networking because of the ability to configure wireless links by nodes autonomously, without any centralized control facilities. Adaptive array antennas (AAA) have been expected to improve the network efficiency by taking advantage of its adaptive beamforming capability. However, it should be noted that AAA is not almighty. Its interference cancellation capability is limited by the degree-of-freedom (DOF) and the angular resolution as a function of the number of element antennas. Application of AAA without attending to these problems can degrade the efficiency of the network. Let us consider wireless ad hoc communication as a target application for AAA, taking advantage of AAA's interference cancellation capability. The low DOF and insufficient resolution will be crucial problems compared to other wireless systems, since there is no centralized facility to control the nodes to avoid interferences in such systems. A number of interferences might impinge on a node from any direction of arrival (DOA) without any timing control. In this paper, focusing on such limitations of AAA applied in ad hoc communications, we propose a new scheme, Forward Interference Avoidance (FIA), using AAA for ad hoc communications in order to avoid problems caused by the limitation of the AAA capability. It enables nodes to avoid interfering with other nodes so that it increases the number of co-existent wireless links. The performance improvement of ad hoc communications in terms of the number of co-existent links is investigated through computer simulations.

As the role of wireless communication is becoming more important for realizing a future connected society for not only humans but also things, spectrum scarcity is becoming severe, because of the huge numbers of mobile terminals and many types of applications in use. In order to realize sustainable wireless connection under limited spectrum resources in a future wireless world, a new dynamic spectrum management scheme should be developed that considers the surrounding radio environment and user preferences. In this paper, we discuss a new spectrum utilization framework for a future wireless world called the “smart spectrum.” There are four main issues related to realizing the smart spectrum. First, in order to recognize the spectrum environment accurately, spectrum measurement is an important technology. Second, spectrum modeling for estimating the spectrum usage and the spectrum environment by using measurement results is required for designing wireless parameters for dynamic spectrum use in a shared spectrum environment. Third, in order to effectively gather the measurement results and provide the spectrum information to users, a measurement-based spectrum database can be used. Finally, smart spectrum management that operates in combination with a spectrum database is required for realizing efficient and organized dynamic spectrum utilization. In this paper, we discuss the concept of the smart spectrum, fundamental research studies of the smart spectrum, and the direction of development of the smart spectrum for targeting the future wireless world.

In this paper, we present a modified image rejection method that uses imbalance compensation techniques for phase and gain in low-intermediate frequency (IF) software-defined radio (SDR) receivers. In low-IF receivers, the image frequency signal interferes with the desired signal owing to the phase and gain imbalances caused by analog devices. Thus, it is difficult to achieve the required image rejection ratio (IRR) of over 60dB without compensation. To solve this problem, we present modified blind compensation techniques based on digital signal processing using a feedback control loop with a practical computation process. The modified method can reduce the complexity when a hardware logic circuit is used, like an FPGA. The simulation and experimental results verify that the modified method achieves an IRR greater than 50-60dB for both the carrier and the modulated waves.

M-ary/SS is a version of Direct Sequence/Spread Spectrum (DS/SS) aiming to improve the spectral efficiency employing orthogonal codes. However, due to the auto-correlation property of the orthogonal codes, it is impossible to detect the symbol timing by observing correlator outputs. Therefore, conventionally, a preamble has been inserted in M-ary/SS signals. In this paper, we propose a new blind adaptive array antenna for M-ary/SS systems that combines signals over the space axis without any preambles. It is surely an innovative approach for M-ary/SS. The performance is investigated through computer simulations.