This paper analyzes and compares two methods to estimate electromagnetically coupled noises introduced to an antenna due to the nearby circuits at a circuit design stage. One of them is to estimate the power spectrum, and the other one is to estimate the active S11 parameter at the victim antenna, respectively, and both of them use simulated standard S-parameters for the electromagnetic coupling in the circuit. They also need the assumed or measured excitation of noise sources. To confirm the validness of the two methods, an evaluation board consisting of an antenna and noise sources were designed and fabricated in which voltage controlled oscillator (VCO) chips are placed as noise sources. The generated electromagnetic noises are transferred to an antenna via loop-shaped transmission lines, degrading the performance of the antenna. In this paper, detailed analysis procedures are described using the evaluation board, and it is shown that the two methods are equivalent to each other in terms of the induced voltages in the antenna. Finally, a procedure to estimate antenna performance degradation at the design stage is summarized.

With the advantages of higher blocking voltage, higher operation temperature, fast-switching characteristics, and lower switching losses, the silicon carbide (SiC) MOSFET has attracted more attentions and become an available replacement of traditional silicon (Si) power semiconductor in applications. Despite of all the merits above, electromagnetic interference (EMI) issues will be induced consequently by the ultra-fast switching transitions of the SiC MOSFET. To quickly and precisely assess the switching behaviors of the SiC MOSFET for EMI investigation, an analytical model is proposed. This model has comprehensively considered most of the key factors, including parasitic inductances, non-linearity of the junction capacitors, negative feedback effect of Ls and Cgd shared by the power and the gate stage loops, non-linearity of the trans-conductance, and skin effect during voltage and current ringing stages, which will considerably affect the switching performance of the SiC MOSFET. Additionally, a finite-state machine (FSM) is especially utilized so as to analytically and intuitively describe the switching behaviors of the SiC MOSFET via Stateflow. Based on double pulse test (DPT), the effectiveness and correctness of the proposed model are validated through the comparison between the calculated and the measured waveforms during switching transitions. Besides, the model can appropriately depict the spectrum of the drain-source voltage of the MOSFET and is suitable for EMI investigation in applying of SiC devices.

In this study, we propose a two-step approach to evaluate electromagnetic interference (EMI) with a wearable vital signal sensor. The two-step approach combines a quasi-static electromagnetic (EM) field analysis and an electric circuit analysis, and is applied to the EMI evaluation at frequencies below 1 MHz for our developed wearable electrocardiogram (ECG) to demonstrate its usefulness. The quasi-static EM field analysis gives the common mode voltage coupled from the incident EM field at the ECG sensing electrodes, and the electric circuit analysis quantifies a differential mode voltage at the differential amplifier output of the ECG detection circuit. The differential mode voltage has been shown to come from a conversion from the common mode voltage due to an imbalance between the contact impedances of the two sensing electrodes. When the contact impedance is resistive, the induced differential mode voltage increases with frequency up to 100kHz, and keeps constant after 100kHz, i.e., exhibits a high pass filter characteristic. While when the contact impedance is capacitive, the differential mode voltage exhibits a band pass filter characteristic with the maximum at frequency of around 150kHz. The differential voltage may achieve nearly 1V at the differential amplifier output for an imbalance of 30% under 10V/m plane-wave incident electric field, and completely mask the ECG signal. It is essential to reduce the imbalance as much as possible so as to prevent a significant interference voltage in the amplified ECG signal.

This paper shows that the induced peak voltage on the short monopole antenna by the EM field radiated from a small gap discharge when the gap width was experimentally changed from 10 to 360µm was not directly proportional to the discharge voltage between the gap. It was found that the 10mm short monopole antenna induced peak voltage had a peak value between 40 and 60µm gap width.

Frequency-modulated clock signals are widely used in personal computers to reduce the amplitude of the clock harmonic noise, as measured using an electromagnetic interference (EMI) test receiver. However, the power of the clock harmonics is not decreased with this technique called spread spectrum clocking (SSC). Hence, the impact of the harmonics of a frequency-modulated clock on the bit error rate (BER) and packet error rate (PER) of a Bluetooth system is theoretically analyzed. In addition, theoretical analysis covers the effectiveness of a frequency hopping spread spectrum (FH-SS) scheme and forward error correction (FEC) in mitigating the degradation in the BER and PER caused by clock harmonic interference. The results indicate that the BER and PER strongly depend on the modulating frequency and maximum frequency deviation of the clock harmonic. They also indicate that radiated clock harmonics may considerably degrade the BER and PER when a Bluetooth receiver is very close to a personal computer. Frequency modulating the clock harmonics slightly reduces the BER while it negligibly reduces the PER.

In this paper a second order Volterra series model of an operational amplifier (opamp) circuit is presented. Such a model is suitable to the investigation of the rectification and demodulation effects of radio frequency (RF) interference superimposed on the nominal input signals and on the power supply voltage of an opamp. On the basis of the new model, some design criteria to improve the immunity of opamps to RF interference are proposed. Model predictions are verified by comparison with experimental test results.

We investigate the statistical features of both random- and chaos-based FM timing signals to ascertain their applicability to digital circuits and systems. To achieve such a goal, we consider both the case of single- and two-phase logic and characterize the random variable representing, respectively, the time lag between two subsequent rising edges or between two consecutive zero-crossing points of the modulated timing signal. In particular, we determine its probability density and compute its mean value and variance for cases which are relevant for reducing Electromagnetic emissions. Finally, we address the possible problems of performance degradation in a digital system driven by a modulated timing signal and to cope with this we give some guidelines for the proper choice of the statistical properties of the modulating signals.

Anechoic chambers have been effectively used for microwave propagation, electromagnetic interference (EMI) and immunity testing. The electromagnetic compatibility (EMC) problem has recently become serious and many of these chambers have been constructed. The results of a questionnaire survey sent to anechoic chamber manufacturers are described that a total of 450 anechoic chambers have been constructed in Japan since 1964. Twenty years ago the purpose of the chambers was microwave propagation research, but more than 50 each year have recently being built for EMC/EMI and immunity testing. Their size has gradually been reduced by the use of absorbing materials such as ferrite with dielectric materials. The lowest frequency of most chambers is 30MHz for the 3 m method of site attenuation.