Many previous works state that a multiple Sidelobe canceller (MSLC) with two auxiliary antennas is successful in suppressing two interference signals received simultaneously by sidelobes of a main antenna. In this paper, we show that the MSLC does not always guarantee such capability in three dimensional applications where the incident direction of interference signals is defined by two angles (elevation and azimuth). We show the singularity of the autocorrelation matrix for the auxiliary channel signals induces the degradation of the capability by analyzing characteristics of MSLC's in three dimensional applications from the view point of the eigenvalue problem. To overcome this singularity, we propose a novel MSLC controlling the placement of auxiliary antennas by means of switching over three antennas arranged triangularly. Some simulations are conducted to show the effectiveness of the proposed MSLC.

Results of a DC motor driving test with a power sent by a microwave and extracted with a rectenna array are reported. No significant difference has been observed in the output DC power from the rectenna array between a motor load and a resistive load. Mechanical output could be extracted from the received microwave power with an efficiency of 26%.

Resonant slots are widely used for conventional slotted waveguide array. Reflection from each slot causes a standing wave in the waveguide and beam tilting technique is essential to suppress the reflection at the antenna input port. But the slot reflection narrows the overall frequency bandwidth and the design taking it into account is complicated. This paper proposes a reflection cancelling slot pair as an array element, which consists of two slots spaced by 1/4λg. Round trip path-length difference between them is 1/2λg and reflection waves from a pair disappear and traveling-wave excitation in the waveguide is realized. The full wave analysis reveals that mutual coupling between paired slots is large and seriously reduces the radiation from a pair. Offset arrangement of slots in a pair is recommended to decrease the mutual coupling and to realize strong coupling. In practical array design, the mutual couplings from other pairs were simulated by imposing periodic boundary conditions above the aperture. To clarify the advantages of the slot pair over a conventional resonant slot, the predicted characteristics are compared. Reflection characteristics of the array using the slot pair is excellent and a boresite beam array can be realized. In addition, a slot pair can realize stronger coupling than the conventional resonant slot, while the bandwidth of the former in terms of the aperture field phase illumination is narrower than that of the latter. These suggests that the slot pair array is much more suitable for a small array than conventional one. Finally, the predicted characteristics are confirmed by experiments.

The TACAN is located where there is no obstruction to its line-of-sight coverage. When it snows, its radome, particularly its windward side is covered with snow. This partial snow attaching on the radome causes azimuth error of the TACAN. In this paper, a simple computer simulation for estimation of the azimuth error caused by such snow attaching is proposed. Then we checked the simulation results against the test results of the azimuth error due to pseudo ice/snow layer and the results of measurements in the fields. Finally, we propose a spherical radome to alleviate this problem and its test results are presented. We think that this study is also applicable for radar antennas.

A new pattern synthesis method for multibeam reflector antennas is described. The Directional Constrained Minimum Power (DCMP) method, which was developed as an adaptive array algorithm, has been applied to reflector antennas with cluster feeds. The main objective of this pattern synthesis is to optimize the excitation distribution of the cluster primary feed in order to reduce the sidelobe level and to attain a high main beam gain. A desired contour beam pattern has also been attained by modifying this method. Furthermore, this paper describes other applications of this method, such as pattern optimization taking account of the frequency characteristics and the change in the radiation pattern due to an antenna pointing system, cross-polarization reduction, and monopulse pattern synthesis for an RF sensor.

The authors propose a multiple shaped beam antenna which uses a single shaped reflector and simple feeds. This new type of multibeam antenna is very attractive for satellite communications and broadcasting because its beam-forming network is much simpler than conventional multibeam reflector antennas which uses cluster feeds. The design method for shaping the reflector surface is described, which is based on the concept of an equivalent array. By using this method, a design example is shown, in which the Japanese main islands are covered with four beams and twofold frequency reuse is operated. Also, the basic performance of this new antenna is clarified numerically.

The relation between the radiation pattern and the dimension of the conducting box for a portable telephone is illustrated both theoretically and experimentally. The Galerkin-moment method using the Fourier series expansion for the surface current of the conducting box, which has a great advantage of having a high accuracy, is employed to obtain the radiation pattern. As an example of antennas, a quarter-wavelength monopole antenna having a sinusoidal current distribution is used. As a result, it is pointed out that the radiation pattern of a monopole antenna mounted on the box tends to tilt in a lower direction both in theory and in experiment as well. The relation between the radiation pattern and the location of the monopole antenna is also described. An asymmetrical, or distorted pattern is observed when the monopole antenna moves away from the center of the top plane.

This paper discusses the fully three-dimensional finite difference time domain (FDTD) method to analyze a monopole antenna mounted on a rectangular conducting box covered with a layer of dielectric. The effects of the conductivity and the permittivity of the dielectric layer are investigated. It is shown that all calculation results agree very well with the measured data.

By using measured attenuation time-series data over 2 years at 19.5GHz with an integration time of 1 sec, effects of the integration time on attenuation statistics are presented. It is observed that the effect on cumulative distribution of attenuation and the relation between annual and the worst-month cumulative time percentages are not significant for the practical prediction purposes. The effect is significant in attenuation duration statistics.

An omnidirectional microstrip antenna using a parasitic cylinder is presented. A rectangular patch is formed on a dielectric substrate and it's completely covered with an aluminum cylinder which is somewhat shorter than a half of free space wavelength. Under such configuration the aluminum cylinder works as a parasitic element. This antenna can provides uniform omnidirectional radiation patterns and a broad frequency bandwidth. In this paper an experimental method for designing such an element is described. Measured input impedance characteristics, current distribution around the surface of the cylinder and patterns are also shown. By properly adjusting the coupling intensity between the patch and the parasitic cylinder a broad bandwidth antenna element can be realized. Some methods to adjust the coupling intensity are shown. A wide bandwidth element up to 14% for VSWR1.5 is obtained. Arranging many patches lengthways on a substrate and placing metallic cylinders around each patches, we can realize a high-gain and broad bandwidth collinear antenna.

A theoretical and experimental study of a thin card-sized antenna is presented. The method of moment with a wire-grid model is used to analyze this antenna. In order to validate numerical efficiency, measurements using Wheeler method are preformed on this antenna and its wire-grid models. The experimental and theoretical results are in good agreement if the wire conductivity is well chosen. And the noise reduction of measured Wheeler efficiency using least mean square method is also examined.

A new superresolution technique is proposed for antenna pattern measurements. Unwanted reflected signals often impinge on the antenna when we measure it outdoors. A time-domain superresolution technique (a MUSIC algorithm) has been proposed to eliminate the unwanted signal for a narrow pass-band antenna. The MUSIC algorithm needs many snapshots to obtain a correlation matrix. This is not preferable for antenna pattern measurements because it takes a long time to obtain the data. In this paper, we propose to reduce a noise component (stochastic quantity) using the FFT and gating techniques before we apply the MUSIC. The new technique needs a few snapshots and saves the measurement time.

A best-fit panel model in the radio holographic metrology taking into account locations and sizes of actual surface panels in a large reflector antenna is presented. A displacement and tilt of each panel can be estimated by introducing the best-fit panel model. It was confirmed by simulations that the distinction can be drawn between a continuous surface error and a discontinuous one. Errors due to truncation of the radiation pattern were calculated by simulations. It was found that a measurement of a 128128 map is optimum for the 45-m telescope. The reliability of the measurements using this model was examined by experiments with panel displacements. Panel adjustments using the best-fit panel model successfully improved the surface accuracy of the antenna from 138µm rms to 84µm rms (/D=210-6).

Numerical analysis of the electromagnetic radiation from conducting surface structures is concerned. The method of moments is discussed with the surface-patch modeling in which the surface quantities, i.e. the current, charge and impedance are directly introduced and with the wire-grid modeling in which the surface quantities are approximated by the filamentary traces. The crucial element to a numerical advantage of the wire-grid modeling lies in the simplicity of its mathematical involvements that should be traded for the uncertainties in the construction of the model. The surface-patch techniques are generally not only clear and straightforward but also more reliable than the wire-grid modeling for the computation of the surface quantities. In this work, we bring about a comparative discussion of the two approaches while the analysis of a built-in planar antenna is reported. For the purpose of the comparison, the same electric field integral equation and the Galerkin's procedure with the linear expansion/testing functions are used for both the wire-grid and surface-patch modeling.

This paper describes a novel method to calculate the fields scattered by a polyhedron structure for an incident plane wave. In this method, the fields diffracted by an edge are calculated using the equivalent edge currents which are separated into components dependent on each of the two surfaces which form the edge. The separated equivalent edge currents are based on the Geometrical Theory of Diffraction (GTD). Using this Separated Equivalent Edge Current Method (SEECM) , fields scattered by a polyhedron structure can be calculated without special treatment of the singularity in the diffraction coefficient. This method can be also applied successfully to structures with convex surfaces by modeling them as polyhedron structures.

The antennas for subsurface radar are usually covered with a conducting cavity to prevent the radiation field from affecting the electromagnetic environment and to protect the received field from external noises. Furthermore, radiowave absorber is attached to the interior wall of the cavity in order to suppress the multiple reflections in the cavity. In this paper, the characteristics of the two-dimensional cavity-backed antenna having the absorber and the over-all properties of this subsurface radar due to buried objects are numerically analyzed by the Finite-Difference Time-Domain method. It is shown that the pulse propagation in the ground is confined to the narrow region due to the cavity. It is also shown that the multiple reflections in the cavity are effectively suppressed by choosing the suitable absorber, and so that the distinctive pulse echo can be obtained.

A cylindrical active phased array antenna was developed. A primary surveillance radar (PSR) antenna and a secondary surveillance radar (SSR) antenna are integrated conformally. The PSR antenna employs two-dimensional electronic beam scanning. The SSR antenna employs electronic beam scanning in azimuth. Advantages of this antenna, design architecture employed and measured characteristics are described.

We analyze the mutual coupling between two microstrip antennas (MSAs) with the finite-difference time-domain (FDTD) method. It is suitable for substrates which have a complex configuration or include feed line structures. The mutual coupling between two MSAs on discontinuous orthogonal substrates is successfully calculated.

A radial line slot antenna (RLSA) is a high gain and high efficiency planar array. A single-layered RLSA is much simple in structure but the slot length must be varied to synthesize uniform aperture illumination. These are now commercialized for 12GHz band DBS reception. In RLSAs, considerable power is dissipated in the termination as is common to other traveling wave antennas; the uniform aperture illumination is not the optimum condition for high gain in RLSAs. Authors proposed a theoretical method reducing the termination loss for further efficiency enhancement. This paper presents the measured performances of the SL-RLSAs of this design with non-uniform aperture illumination. The efficiency enhancement of about 10% is observed; the measured gain of 36.7dBi (87%) and 32.9dBi (81%) for a 0.6mφ and 0.4mφ antennas respectively verify this technique.

In a two-layer self-diplexing antenna fed at two ports, theoretical analysis has already shown that the isolation characteristics can be improved by adjusting the angle between the feed locations of the transmitting and receiving antennas. In this letter, we experimentally investigate the isolation characteristics of the self-diplexing array antenna. First, calculated and experimental results for each feed location of the element antenna are compared and good agreement is found. Second, experimental results with a 19-element planar array indicate that a self-diplexing antenna with suitably chosen feed configuration is effective in improving the isolation in a phased array antenna.