Effective user accommodation will be more and more important in passive optical networks (PONs) in the next decade since the number of subscribers has been leveling off as well and it is becoming more difficult for network operators to keep sufficient numbers of maintenance workers. Drastically reducing the number of small-scale communication buildings while keeping the number of accommodated users is one of the most attractive solutions to meet this situation. To achieve this, we propose two types of long-reach repeater-free upstream transmission configurations for PON systems; (i) one utilizes a semiconductor optical amplifier (SOA) as a pre-amplifier and (ii) the other utilizes distributed Raman amplification (DRA) in addition to the SOA. Our simulations assuming 10G-EPON specifications and transmission experiments on a 10G-EPON prototype confirm that configuration (i) can add a 17km trunk fiber to a normal PON system with 10km access reach and 1 : 64 split (total 27km reach), while configuration (ii) can further expand the trunk fiber distance to 37km (total 47km reach). Network operators can select these configurations depending on their service areas.

To drastically increase the splitting ratio of extended-reach (40km span) time- and wavelength-division multiplexed passive optical networks (WDM/TDM-PONs), we modify the gain control scheme of our automatic gain controlled semiconductor optical amplifiers (AGC-SOAs) that were developed to support upstream transmission in long-reach systems. While the original AGC-SOAs are located outside the central office (CO) as repeaters, the new AGC-SOAs are located inside the CO and connected to each branch of an optical splitter in the CO. This arrangement has the potential to greatly reduce the costs of CO-sited equipment as they are shared by many more users if the new gain control scheme works properly even when the input optical powers are low. We develop a prototype and experimentally confirm its effectiveness in increasing the splitting ratio of extended-reach systems to 512.

10G-EPON systems have attracted a great deal of attention as a way of exceeding to realize over 10 Gb/s for optical subscriber networking. Rapid burst-mode transmitting/receiving techniques are the key technologies enabling the burst-mode upstream transmission of 10G-EPON systems. In this paper, we have developed a OLT burst-mode 3R receiver incorporating a burst-mode AGC optical receiver and an 82.5 GS/s over-sampling burst-mode CDR and a ONU burst-mode transmitter with high launch power DFB-LD of 1.27 µm wavelength to fully compliant with IEEE802.3av 10G-EPON PR30 standards. The transmitting characteristics of a fast LD turn-on/off time of less than 6ns and a high launch power of more than +8.0 dBm, and the receiving characteristics of receiver sensitivity of -30.1 dBm and the upstream power budget of 38.1 dB are successfully achieved.

We propose an optical switch control procedure for the Active Optical Access System (AOAS). Optical switches are used in AOAS instead of optical splitters in PON. In the proposed procedure, an OLT determines the switching schedules of optical switches on OSW (Optical Switching Unit) which is installed between OLT and ONU, and informs the OSW of them with a switch control frame preceding of data frame transmission. Then the switch controller on OSW controls the optical switches based on the switching schedules. We developed the prototype systems of OSW, OLT, and ONU. We implemented the optical switch control function with logic circuits on the prototype systems. We demonstrate the proposed procedure works effectively with logic circuits. We also evaluate the 10 Gps optical signal transmission between OLT and ONU. We demonstrate the receiver sensibility on OLT and ONU achieves the distance of 40 km for optical signals transmission with FEC (Forward Error Correction). These receivers are applicable for both AOAS and 10G-EPON.

This paper analyzed the connection points of Main Distribution Frames (MDF), which are installed between outside plants and inside plants (service nodes). This paper also proposes a connecting system for forthcoming FITL (Fiber In The Loop) networks. NTT has developed the Subscriber Line Cross-Connecting Module (LXM) for the FITL network and will continue to introduce LXMs and deploy optic subscriber networks in big cities throughout Japan.