To mitigate the interference caused by frequency reuse between inter-layer and intra-layer users for Non-Orthogonal Multiple Access (NOMA) based device-to-device (D2D) communication underlaying cellular systems, this paper proposes a joint optimization strategy that combines user grouping and resource allocation. Specifically, the optimization problem is formulated to maximize the sum rate while ensuring the minimum rate of cellular users, considering three optimization parameters: user grouping, sub channel allocation and power allocation. However, this problem is a mixed integer nonlinear programming (MINLP) problem and is hard to solve directly. To address this issue, we divide the problem into two sub-problems: user grouping and resource allocation. First, we classify D2D users into D2D pairs or D2D NOMA groups based on the greedy algorithm. Then, in terms of resource allocation, we allocate the sub-channel to D2D users by swap matching algorithm to reduce the co-channel interference, and optimize the transmission power of D2D by the local search algorithm. Simulation results show that, compared to other schemes, the proposed algorithm significantly improves the system sum rate and spectral utilization.

Device-to-device (D2D) communication allows user terminals to directly communicate with each other without the need for any base stations (BSs). Since the D2D communication underlaying a cellular system shares frequency channels with BSs, co-channel interference may occur. Successive interference cancellation (SIC), which is also called the serial interference canceler, detects and subtracts user signals from received signals in descending order of received power, can cope with the above interference and has already been applied to fog nodes that manage communications among machine-to-machine (M2M) devices besides direct communications with BSs. When differences among received power levels of user signals are negligible, however, SIC cannot work well and thus causes degradation in bit error rate (BER) performance. To solve such a problem, this paper proposes to apply parallel interference cancellation (PIC), which can simultaneously detect both desired and interfering signals under the maximum likelihood criterion and can maintain good BER performance even when power level differences among users are small. When channel coding is employed, however, SIC can be superior to PIC in terms of BER under some channel conditions. Considering the superiority, this paper also proposes to select the proper cancellation scheme and modulation and coding scheme (MCS) that can maximize the throughput of D2D under a constraint of BER, in which the canceler selection is referred to as adaptive interference cancellation. Computer simulations show that PIC outperforms SIC under almost all channel conditions and thus the adaptive selection from PIC and SIC can achieve a marginal gain over PIC, while PIC can achieve 10% higher average system throughput than that of SIC. As for transmission delay time, it is demonstrated that the adaptive selection and PIC can shorten the delay time more than any other schemes, although the fog node causes the delay time of 1ms at least.

Device-to-device (D2D) relay enhances the capacity of a mobile network. If the channel quality of a user equipment (UE) is bad, the UE asks a neighbor to get its data from the base station and forward the data to it by using D2D communication. Since cellular and D2D communication can share spectrum resources, the spectral efficiency will rise. As UEs are owned by self-interested users, they may not provide relay services gratis. Thus, some incentive methods let UEs exchange tokens to buy and sell relay services. However, they assume that each relay service is worth one token and offers a fixed data rate, which lacks flexibility. Through the law of supply and demand, this paper proposes an economy aware token-based incentive (EAT-BI) strategy. A supplier (i.e., the service provider) charges different prices for its relay service with different rates. A consumer (i.e., the service requestor) takes different policies to choose a supplier based on its tokens and may bargain with suppliers to avoid starvation. Simulation results show that EAT-BI can efficiently promote D2D relay use and increase throughput under different mobility models of UEs.

In this paper, for improving the robustness of D2D-based SNS by avoiding the cascading failure, we propose an autonomous decentralized friendship management called virtual temporal friendship creation. In our proposed virtual temporal friendship creation, some virtual temporal friendships are created among users based on an optimization problem to improve the robustness although these friendships cannot be used to perform the message exchange in SNS. We investigate the impact of creating a new friendship on the node resilience for the optimization problem. Then we consider an autonomous decentralized algorithm based on the obtained results for the optimization problem of virtual temporal friendship creation. We evaluate the performance of the virtual temporal friendship creation with simulation and investigate the effectiveness of this method by comparing with the performance of a method with meta-heuristic algorithm. From numerical examples, we show that the virtual temporal friendship creation can improve the robustness quickly in an autonomous and decentralized way.

In this study, we propose a mechanism called adaptive failsoft control to address peak traffic in mobile live streaming, using a chasing playback function. Although a cache system is avaliable to support the chasing playback function for live streaming in a base station and device-to-device communication, the request concentration by highlight scenes influences the traffic load owing to data unavailability. To avoid data unavailability, we adapted two live streaming features: (1) streaming data while switching the video quality, and (2) time variability of the number of requests. The second feature enables a fallback mechanism for the cache system by prioritizing cache eviction and terminating the transfer of cache-missed requests. This paper discusses the simulation results of the proposed mechanism, which adopts a request model appropriate for (a) avoiding peak traffic and (b) maintaining continuity of service.

In this paper, in order to avoid the cascading failure by increasing the number of links in the physical network in D2D-based SNS, we propose an autonomous device placement algorithm. In this method, some relay devices are placed so as to increase the number of links in the physical network. Here, relay devices can be used only for relaying data and those are not SNS users. For example, unmanned aerial vehicles (UAV) with D2D communication capability and base stations with D2D communication capability are used as the relay devices. In the proposed method, at first, an optimization problem for minimizing node resilience which is a performance metric in order to place relay devices. Then, we investigate how relay devices should be placed based on some approximate optimal solutions. From this investigation, we propose an autonomous relay device placement in the physical network. In our proposed algorithm, relay devices can be placed without the complete information on network topology. We evaluate the performance of the proposed method with simulation, and investigate the effectiveness of the proposed method. From numerical examples, we show the effectiveness of our proposed algorithm.

Device-to-device (D2D) content delivery reduces the energy consumption of frequent content retrieval in future content-centric cellular networks based on proximal content delivery. Compared with unicast, multicast may be more efficient since it serves the content requests of multiple users simultaneously. The serving efficiency mainly depends on the selection of multicast transmitter, which has not been well addressed. In this letter, we consider the match degree between the multicast content of transmitter and the required content of receiver based on social relationship between transceivers. By integrating the effects of communication environments and match degree into the selection procedure, a multicast UE selection scheme is proposed to improve the number of benefited receivers from D2D multicast. Simulation results show that the proposed scheme can efficiently improve the performance of D2D multicast content delivery under different communication environments.

In this paper, we investigate different power allocation optimization problems with interferences for distributed antenna systems (DAS) with and without D2D communication, respectively. The first objective problem is maximizing spectral efficiency (SE) of the DAS with D2D communication under the constraints of the minimum SE requirements of user equipment (UE) and D2D pair, maximum transmit power of each remote access unit (RAU) and maximum transmit power of D2D transmitter. We transform this non-convex objective function into a difference of convex functions (D.C.) then using the concave-convex procedure (CCCP) algorithm to solve the optimization problem. The second objective is maximizing energy efficiency (EE) of the DAS with D2D communication under the same constraints. We first exploit fractional programming theory to obtain the equivalent objective function of the second problem with subtract form, and then transform it into a D.C. problem and use CCCP algorithm to obtain the optimal power allocation. In each part, we summarize the corresponding optimal power allocation algorithms and also use similar method to obtain optimal solutions of the same optimization problems in DAS. Simulation results are provided to demonstrate the effectiveness of the designed power allocation algorithms and illustrate the SE and EE of the DAS by using D2D communication are much better than DAS without D2D communication.

Large-scale distributed antenna systems (LS-DASs) are gaining increasing interest and emerging as highly promising candidates for future wireless communications. To improve the user's quality of service (QoS) in these systems, this study proposes a user cooperation aided clustering approach based on device-centric architectures; it enables multi-user multiple-input multiple-output transmissions with non-reciprocal setups. We actively use device-to-device communication techniques to achieve the sharing of user information and try to form clusters on user side instead of the traditional way that performs clustering on base station (BS) side in data offloading. We further adopt a device-centric architecture to break the limits of the classical BS-centric cellular structure. Moreover, we derive an approximate expression to calculate the user rate for LS-DASs with employment of zero-forcing precoding and consideration of inter-cluster interference. Numerical results indicate that the approximate expression predicts the user rate with a lower computational cost than is indicated by computer simulation, and the proposed approach provides better user experience for, in particular, the users who have unacceptable QoS.

We consider a device-to-device (D2D) underlaid cellular network where D2D communications are allowed to share the same radio spectrum with cellular uplink communications for improving spectral efficiency. However, to protect the cellular uplink communications, the interference level received at a base station (BS) from the D2D communications needs to be carefully maintained below a certain threshold, and thus the BS coordinates the transmit power of the D2D links. In this paper, we investigate on-off power control for the D2D links, which is known as a simple but effective technique due to its low signaling overhead. We first investigate the optimal on-off power control algorithm to maximize the sum-rate of the D2D links, while satisfying the interference constraint imposed by the BS. The computational complexity of the optimal algorithm drastically increases with D2D link number. Thus, we also propose an on-off power control algorithm to significantly reduce the computational complexity, compared to the optimal on-off power control algorithm. Extensive simulations validate that the proposed algorithm significantly reduces the computational complexity with a marginal sum-rate offset from the optimal algorithm.

During a disaster, users will not be able to communicate with their families and friends using mobile terminals, e.g., smartphones, in many cases due to failures of base stations and backhaul of cellular networks. Even when cellular networks normally operate without failure, they will become seriously congested due to dramatically increased traffic demand. To solve these problems, device-to-device (D2D) communications, in which mobile terminals directly communicate without cellular networks, have been investigated. Multi-hop D2D communication using multiple mobile terminals as relay nodes will be effective in maintaining connectivity during a disaster. It is preferable to estimate the success probability of multi-hop D2D communication by using a simple method that offers optimal parameter control, e.g., the ratio of mobile terminals using D2D communications and the maximum hop length. Moreover, when evaluating the reachability of multi-hop D2D communication, we need to consider the evacuation behavior during a disaster because success probability depends on the geographical distribution of mobile terminals. Therefore, in this paper, we derive a formula for estimating the success probability of multi-hop D2D communication in a simple manner and analyze its reachability using a multi-agent simulation that reproduces the evacuation behavior expected during an earthquake in Tokyo Shinjuku Ward.

We consider device-to-device (D2D) direct communication underlying cellular networks where the D2D link reuses the frequency resources of the cellular downlink. In this paper, we propose a linear precoder design scheme for a base station (BS) and D2D transmitter using the weighted sum-rate of the cellular downlink and D2D link as a cost function. Because the weighted sum-rate maximization problem is not convex on the precoding matrices of BS and D2D transmitters, an equivalent mean-squared error (MSE) minimization problem which is convex on the precoding matrices is proposed by introducing auxiliary matrices. We show that the two optimization problems have the same optimal solution for the precoding matrices. Then, an iterative algorithm for solving the equivalent MSE minimization problem is presented. Through a computer simulation, we show that the proposed scheme offers better weighted sum-rate performance that a conventional scheme.

Public safety networks need to more effectively meet the increasing demands for images or videos to be shared among first responders and incident commanders. Long term evolution (LTE) networks are considered to be candidates to achieve such broadband services. Capital expenditures in deploying base stations need to be decreased to introduce LTE for public safety. However, out-of-coverage areas tend to occur in cell edge areas or inside buildings because the cell areas of base stations for public safety networks are larger than those for commercial networks. The 3rd Generation Partnership Program (3GPP) in Release 13 has investigated device-to-device (D2D) based relay communication as a means to fill out-of-coverage areas in public safety LTE (PS-LTE). This paper proposes a relay selection scheme based on effective path throughput from an out-of-coverage terminal to a base station via an in-coverage relay terminal, which enables the optimal relay terminal to be selected. System level simulation results assuming on radii of 20km or less revealed that the proposed scheme could provide better user ratios that satisfied the throughput requirements for video transmission than the scheme standardized in 3GPP. Additionally, an evaluation that replicates actual group of fire-fighters indicated that the proposed scheme enabled 90% of out-of-coverage users to achieve the required throughput, i.e., 1.0Mbps, to transmit video images.

Device-to-device (D2D) networks are expected to play a number of roles, such as increasing frequency spectrum efficiency and improving throughput at hot-spots. In this paper, our interest is on the potential of D2D on reducing delivery latency. To enable fast D2D network forming, quick device discovery is essential. For quickening device discovery, we propose a method of defining and using common channel and group channels so as to avoid the channel scan uncertainty faced by the conventional method. Rules for using the common channel and group channels are designed. We evaluate and compare the discovery performance of the proposed method with conventional method by using the superframe structure defined in IEEE 802.15.8 and a general discovery procedure. IEEE 802.15.8 is a standard under development for fully distributed D2D communications. A Netlogo simulator is used to perform step by step MAC simulations. The simulation results verify the effectiveness of the proposed method.

With the expected increase in popularity of device-to-device (D2D) services, the importance of implementing an LTE simulator that enables fast and accurate evaluations of D2D related technologies is clear. In this paper, we report on a network simulator, D2dSim, with the aim of realizing an LTE-Advanced network that utilizes the D2D feature, i.e., in which direct transmission between mobile stations (MSs) is enabled. Using NS-3, one of the most popular network simulation platforms, D2dSim could become one of the first realistic open-source D2D-capable environments, providing realistic and standard-compliant implementations of a subset of Proximity-based Services complying with the LTE-A standard.

3GPP (3rd Generation Partnership Project) has started to discuss D2D (Device-to-Device)-aided OTDOA (Observed Time Difference Of Arrival) as one of the mobile positioning enhancement techniques for LTE (Long Term Evolution) systems. It is a kind of multi-node based OTDOA which directly receives D2D signals from adjacent multiple UEs (User Equipment) to measure RSTD (Reference Signal's Time Difference). D2D signals provide valuable advantages in terms of OTDOA positioning because it can guarantee more reference nodes and high SNR (Signal-to-Noise Ratio) of PRS (Positioning Reference Signal). Two typical methods for multi-node based OTDOA can be applied to D2D-aided OTDOA. Multiple OTDOA positioning is one of the multi-node based methods that averages multiple results from OTDOA; however, it cannot always guarantee high accuracy due to the non-uniform geometry of UEs. OTDOA positioning based on TSE (Taylor Series Expansion) algorithm may be one of the solutions; however, it has the initial value problem and high computational complexity due to its iterative procedure. Therefore, in this paper, we propose a novel D2D-aided OTDOA positioning method which utilizes UEs not as reference node of OTDOA but as assisting node for RSTD error reduction. The proposed method can reduce RSTD error of eNB based hyperbola by using multiple hyperbola bands. The hyperbola band indicates the possible range in which a hyperbola can occur due to RSTD error. Then, by using principal axes of hyperbolas, we estimate a modified hyperbola from the overlap area of hyperbola bands, which has less RSTD error. We verify that the proposed method can effectively reduce RSTD error and improve positioning performance with lower computational complexity.

We herein describe an autonomous peer discovery scheme for Device-to-Device (D2D) communications. With the increasing popularity of D2D communications, an efficient means of finding the neighboring node, i.e., peer discovery, is required. To this end, we propose a new autonomous peer discovery scheme that uses azimuth spread (AS), delay spread (DS), and shadow fading of the uplink pilot from each mobile station (MS). Given that AS, DS, and shadow fading are spatially correlated, nodes that have similar values must be neighbors. The proposed scheme filters out the MSs that are unlikely to be neighbors and uses the Kolmogorov-Smirnov (K-S) test to improve the accuracy of neighbor discovery. Unlike previous peer discovery schemes that incur additional signaling overheads, our proposal finds neighboring nodes by using the existing uplink pilot transmission from MSs such that neighboring peers can be found autonomously. Through analysis and simulation, we show that neighboring MSs can be found accurately with low latency.

One of the most important processes in cellular-assisted device-to-device (D2D) communications is device discovery, which decides whether two devices are located close to each other. The discovery process is performed by devices periodically transmitting discovery signals so that neighbor devices can receive them to recognize their proximate physical presence. While a fixed set of discovery parameters are used regardless of devices in most of the existing works, discovery periods are not necessarily the same for all devices, as they can be set differently depending on their channel conditions and operational environments, e.g., the mobile speeds. In this paper, we present an optimization framework to determine the discovery periods for individual devices in cellular-assisted D2D communication systems. We consider two different types of optimization problems, taking the different user velocities into account: minimizing the average number of undiscovered device pairs, and minimizing the number of discovery signal transmissions while maintaining the average number of undiscovered device pairs for each device less than a pre-specified threshold. We present analytical and simulation results to demonstrate that short discovery periods can be beneficial to high-mobility devices, while longer discovery periods are allowed for devices with lower velocities.

In recent 3GPP (3rd Generation Partnership Project) standardization meetings, D2D (Device-to-Device) discovery has been a major issue to support commercial/social services and public safety in disaster environment, and TDM (Time Division Multiplexing) based discovery channel structure is mainly considered to prevent mutual interference between D2D and cellular traffic. In this structure, D2D discovery among the same cell UEs (User Equipment) has no problem because they have the same timing source. However, LTE (Long Term Evolution) assumes an asynchronous network where two adjacent eNBs (evolved Node B) have a symbol-level timing offset. For that reason, asynchronous interference among discovery signals can appear in inter-cell D2D discovery. Therefore, channel re-use scheduling was studied previously in which neighboring cells do not use the same portion of the extended discovery channel and other non-neighboring cells re-use it. However, it still shows interference problems in small cell networks which cause substantial cellular traffic loss. Therefore, in this paper, we propose a novel discovery channel scheduling in which eNBs time-align their discovery channels from each other by sample-level. In the proposed scheme, serving eNB requests cell edge UEs to estimate NTD (Network Time Difference) between serving eNB and neighboring eNB. Then, considering multiple NTDs, eNB adjusts the sample position of its discovery channel based on a novel decision rule. We verify that the proposed scheme can match the discovery performance of a synchronous network with less cellular uplink loss.

Device-to-device (D2D) multicast communication is a useful way to improve the communication efficiency of local services. This study considers a scenario of D2D multicast communication in a single frequency network (SFN) system and investigates the frequency resource allocation problem. Firstly, we propose that D2D user equipments (DUEs) do not share frequency with cellular user equipments (CUEs) in the same SFN, but reuse frequency with CUEs in other SFNs, by which the interference between D2D and cellular communications can be avoided. Then, under the principle that two nearest D2D multicast groups cannot reuse the same frequency, the study develops a distance-based fair frequency resource allocation (DFRA) algorithm. The DFRA algorithm ensures control of the interference within a reasonable range and fairly allocate the available frequency resources to the D2D multicast groups. Numerical simulation results show that the proposed resource allocation algorithm is effective in improving the data rate and reducing the outage probability for D2D communications.