A method is proposed for estimating code and carrier phase parameters of GNSS reflected signals in low SNR (signal-to-noise ratio) environments. Simulation results show that the multipath impact on code and carrier with 0.022 C/A chips delay can be estimated in 0 dB SNR in the condition of 46 MHz sampling rate.

An AuSn reflow process using hydrogen radicals as a way to avert the cleaning of flux residues was investigated for its application to solder bumping. AuSn particles (manufactured by a gas atomizer) smaller than 5 µm, which are difficult to reflow by conventional methods that use rosin mildly activated (RMA) flux, were used for the experiments. In this process, the reduction effect by the hydrogen radicals removes the surface oxides of the AuSn particles. Excellent wetting between 1-µm-diameter AuSn particles and Ni metallization occurred in hydrogen plasma. Using hydrogen radicals, 100 µm-diameter AuSn bumps without voids were successfully formed at a peak temperature of 300. The average bump shear strength was approximately 73 gf/bump. Bump inspection after shear testing showed that a fracture had occurred between the Au/Ni/Cr under bump metallurgy (UBM) and Si substrate, suggesting sufficient wetting between the AuSn bump and the UBM.

This paper reexamines reflection and transmission of a TE plane wave from a two-dimensional random slab discussed in the previous paper [IEICE Trans. Electron., Vol.E79-C, no.10, pp.1327-1333, October 1996] by means of the stochastic functional approach with the multiply renormalizing approximation. A random wavefield representation is explicitly shown in terms of a Wiener-Hermite expansion. The first-order incoherent scattering cross section and the optical theorem are numerically calculated. Enhanced scattering as gentle peaks or dips on the angular distribution of the incoherent scattering is reconfirmed in the directions of reflection and backscattering, and is newly found in the directions of forward scattering and 'symmetrical forward scattering.' The mechanism of enhanced scattering is deeply discussed.

This paper presents an easy and efficient modification of simplified 2D ray-launching method, by approximately including multiple reflection effect inside walls for indoor environment. In order to precisely carry out the ray-launching procedure inside lossy wall, a simple modification using a true real refraction angle is first introduced, instead of complex one. Furthermore, an efficient approximation is carried out to collect the internal multiple reflected rays into the primary one. We here call it collective ray approach. Consequently, it is confirmed from the detailed considerations that the present ray representations obtained by introducing the real refraction angle are well suitable for indoor propagation analysis, and in particular the collective ray solution can be utilized confidently even when the internal reflections strongly contribute to the propagation feature of the considered indoor environment.

A trihedral corner reflector is often used for SAR polarimetric calibration. However, the scattering property of the reflector used for the calibration may not be correct if the high frequency approximation is not satisfied or if an incident angle deviates from the symmetric axis of the reflector. In order to know the conditions for precise SAR polarimetric calibration, we evaluated the polarimetric response of the reflector by a numerical simulation using the method of moment (MoM). It is found that allowable incident angle deviation is 5 degree to azimuth direction and 4 degree to elevation direction for precise SAR polarimetric calibration when the size of the reflector is 7.5 times larger than the wavelength of an incident wave.

In this study, attenuated total reflection (ATR) utilizing surface plasmon (SP) excitation and SP emission lights were observed for the adsorption of polystyrene (PS) spheres and a water-soluble polymer. The PS spheres contained fluorescent dyes and exhibited red fluorescence. The ATR properties indicated film deposition with increasing number of adsorption cycles. The SP emission light induced by the fluorescent dye in the spheres was also measured, and an increase in the peak intensity, as well as an angle shift, was observed. Furthermore, the SP emission light spectra were investigated at various emission angles. The dispersion relation obtained from the SP emission light almost corresponded to that obtained from the ATR curves.

Gas or water leaks in pipes that are buried under ground or that are situated in the walls of buildings may occur due to aging or unpredictable accidents, such as earthquakes. Therefore, the detection of leaks in pipes is an important task and has been investigated extensively. In the present paper, we propose a novel leak detection method by means of acoustic wave. We inject an acoustic chirp signal into a target pipeline and then estimate the leak location from the delay time of the compressed pulse by passing the reflected signal through a correlator. In order to distinguish a leak reflection in a complicated pipeline arrangement, the reflection characteristics of leaks are carefully discussed by numerical simulations and experiments. There is a remarkable difference in the reflection characteristics between the leak and other types of discontinuity, and the property can be utilized to distinguish the leak reflection. The experimental results show that, even in a complicated pipe arrangement including bends and branches, the proposed approach can successfully implement the leak detection. Furthermore, the proposed approach has low cost and is easy to implement because only a personal computer and some commonly equipment are required.

We propose a new bidirectional gigabit mm-wave wavelength division multiplexed-radio over fiber link which shares the same wavelength. As the downlink, the central station transmits a 30 GHz single sideband wireless signal which is modulated 1.25 Gbps and also transmits a remote 32 GHz local oscillator for down-conversion of a uplink wireless signal by using a mach-zehnder modulator and a fiber bragg grating. As the uplink, the base station transmits a down-converted 1.25 Gbps wireless signal by using a reflective semiconductor optical amplifier. We achieve a BER < 10-9 in the downlink at -14.05 dBm and uplink at -12.5 dBm after 20 km transmission.

As THz wave has the advantages of enough resolution and penetration to materials, it has been examined to be used for the imaging system. The propagation distance of THz wave is limited to be short. That is also the advantage for application to the indoor wireless communication etc. For the achievement of the ultra-high frequency oscillator (and concurrently transmitter) device, the properties of small, electronic excitation, the antenna constructed and being on the wafer are important. For the purpose, the Negative differential resistance Dual channel transistor (NDR-DCT) proposed by AIST is utilized. In this paper, as an initial theoretical analysis, we simulated the oscillation frequency of this device at about 100 GHz-1THz within the Terahertz band on which the above applications was expected. The equivalent circuit model of NDR-DCT was shown based on the analogy with the resonant tunnelling diode (RTDs), and the antenna as the resonance circuit part was designed by the numerical analysis. The possibility of the THz oscillation of this device was confirmed. The slit reflector that we proposed can realize the slot antenna on the device effectively and is suitable for three terminal structure semiconductor. its manufacturing is relatively easy.

A design method is proposed for a low-profile dual-shaped reflector antenna for the mobile satellite communications. The antenna is required to be low-profile because of mount restrictions. However, reduction of its height generally causes degradation of antenna performance. Firstly, an initial low-profile reflector antenna with an elliptical aperture is designed by using Geometrical Optics (GO) shaping. Then a Physical Optics (PO) shaping technique is applied to optimize the gain and sidelobes including mitigation of undesired scattering. The developed design method provides highly accurate design procedure for electrically small reflector antennas. Fabrication and measurement of a prototype antenna support the theory.

This paper deals with a TM plane wave reflection and transmission from a one-dimensional random slab with stratified fluctuation by means of the stochastic functional approach. Based on a previous manner [IEICE Trans. Electron. E88-C, 4, pp.713-720, 2005], an explicit form of the random wavefield is obtained in terms of a Wiener-Hermite expansion with approximate expansion coefficients (Wiener kernels) under small fluctuation. The optical theorem and coherent reflection coefficient are illustrated in figures for several physical parameters. It is then found that the optical theorem by use of the first two or three order Wiener kernels holds with good accuracy and a shift of Brewster's angle appears in the coherent reflection.

An important issue in the realization of optical packet-switched (OPS) networks is the resolution of packet contention caused by the lack of RAM-like optical buffering. Although an optical buffer using fiber delay lines (FDLs) has been proposed, its capacity is extremely limited. There have been several studies of this problem. One approach is deflection routing, which is widely used in electronic packet-switched networks or optical burst-switched (OBS) networks. However, in OPS networks, packet lengths are short, so that the speed requirement for route lookup is very stringent. If the network topology is geometric, such as a Manhattan Street Network (MSN), hop-by-hop routing can be implemented by simple optical logic devices without an electronic routing table. However, if the topology is not geometric, it is hard to implement deflection routing electronically or optically. Another approach is reflection routing, which is easy to implement but has a higher probability of packet loss than does deflection routing. In this paper, we propose a packet contention resolution scheme, reflection-based deflection routing, which is based on reflection routing and enables switching the reflected packet to an alternate path if its primary path remains congested. Our method alleviates the time limitation on setting an alternate path by making use of the packet reflection latency and also reduces the probability of packet loss. We evaluate the performance of the proposed method by simulation experiments and show its effectiveness.

A passive optical network (PON) that provides fiber to the home (FTTH) services is a fundamental access network topology in Japan. An optical fiber line monitoring and testing system is essential if we are to improve service reliability and reduce the maintenance costs of optical access networks. PONs have optical splitters in their optical fiber lines. It is difficult to find a fault in an optical fiber line equipped with an optical splitter by using a conventional optical fiber line testing system, which uses optical time-domain reflectometer (OTDR) in a central office (CO), because Rayleigh backscattering from the branched fibers accumulates in the OTDR trace. This paper describes a newly developed optical fiber line testing method that employs bi-directional OTDRs with two wavelengths at branched fiber regions in a PON to locate a fault precisely. Optical fiber line testing is conducted by two OTDRs that are installed in a CO and on a customer's premises, respectively. The OTDR in the CO has a U-band maintenance wavelength. We present two kinds of maintenance wavelength allocation for OTDRs on a customer's premises, which are in the U-band and C-band respectively. An OTDR whose maintenance wavelength is in the U-band enables us to test in-service PON lines simply by filtering the U-band wavelength. For the maintenance wavelengths in the C-band, we can use a cost-effective conventional OTDR to test the PON from the customer's premises on condition that we clarify the peak pulse power limit and dynamic range. We describe the test procedures for both cases. We also clarify the insertion loss design for an optical filter in the CO when using the U-band to provide the maintenance wavelength and the criteria for in-service line testing when the using C-band to provide the maintenance wavelength. To confirm the feasibility of our approach, we demonstrate a bi-directional OTDR method using the U-band and the C-band, and the test procedure, which successfully detected fault locations in branched fiber regions. We also describe the use of packet loss measurements to investigate the effect of in-service line testing with an OTDR in the C-band on data communication quality.

Inter-Vehicle Communication (IVC) is one of the most important technologies to realize advanced Intelligent Transport Systems (ITS). We extensively apply the IVC technology to the communications between pedestrians and vehicles. We call this kind of communications VPEC (Vehicle-PEdestrian Communications). The objective of this paper is to present an effective control scheme for VPEC and to evaluate the performance of proposed scheme by experiments. We deal with direct communications between pedestrians and vehicles. Due to the battery shortage of pedestrians' terminals (p-node), we have presented a reflect-transmission scheme. In this paper, we propose a new access protocol for reflect-transmission scheme, and show its validity by various experiments with several vehicles.

The reflection method is an accurate and simple method for measuring the radiation efficiency of a small antenna. However, it takes too long and has the disadvantage of underestimating the efficiency due to resonance in the cavity formed by the straight waveguide and two sliding shorts. To reduce the measurement time, one sliding short can be fixed while the other one is moved. To improve the accuracy of this technique, we can set the antenna to be measured at the center of the two sliding shorts or at a local anti-node of the standing wave in the waveguide. When one of the sliding shorts is fixed, the measured efficiency becomes negative at certain frequencies. We examine these reductions in efficiency using an equivalent transmission line model for the reflection method. We also derive analytical expressions for the overall efficiency in the above cases and verify new procedures that enable measurements to be performed without any drops in the measured efficiency.

The effect of wall and indoor scatterers on the indoor multiple input multiple output (MIMO) communication system is investigated by using the hybrid technique of finite difference time domain (FDTD) method and method of moments (MoM). MIMO channel capacity with the wall reflection is investigated with consideration of the eigenvalue of channel covariance matrix, the received power and the effective multipaths of MIMO system. It is found that the stronger side wall reflection can lead to the higher MIMO channel capacity. MIMO system with indoor scatterers is also analyzed and compared with the line of sight (LOS) indoor MIMO system. It is found that the scatterer material has different effect on the received power and the effective multipaths of MIMO system.

In this paper, CPW-fed slot antennas using loading metallic strips and a widened tuning stub (CPW-FSLW) which provides wideband operation on the flat, a Λ-shape reflector with horizontal plate that prevents the back radiation and provides the uni-directional radiation are investigated. We observe that the size and shape of the reflector have significant impact on the impedance matching and radiation patterns. By fabricating the CPW-FSLW on the Λ-shape reflector with horizontal plate structure, noticeable enhancements in both radiation pattern and bandwidth are achieved. The antennas are verified both through numerical simulations and also measurements of the experimental prototypes and these confirm the good performance antennas. It is found that the proposed antenna can deliver a measured impedance bandwidth of 64% from 1.6 to 3.1 GHz for VSWR ≤ 2. The antennas are designed to have wideband operation suitable for applications in GSM1800, GSM1900, PCS, IMT-2000 and WLAN bands.

This paper presents the switched-beam slot antenna over the electromagnetic band-gap (EBG) reflector. This antenna is composed of two slot elements fed with a phase difference and the EBG reflector, which is used in order to realize a low profile structure. The radiation characteristics of this antenna are calculated using the FDTD method. Calculations show that the height of the antenna using the EBG reflector is 60 % lower than that of the antenna using a perfect electric conductor (PEC) reflector. The radiation characteristics at the center of the operating frequency band in the EBG reflector are equivalent to that in the PEC reflector. It is shown that the tilt angle of the main beam in the elevation plane varies with the operating frequency, and the variation in the case of the EBG reflector is caused by its frequency-dependent reflection phase. Moreover, the radiation pattern of the fabricated antenna is measured. The results demonstrate that the low profile design can be achieved by using the EBG reflector, and reveal the influence of the EBG reflector on the antenna efficiency.

To overcome the demerits of two passive optical networks; the small link capacity of the TDM-PON, and the ineffective link utilization of the WDM-PON; we propose a novel access network architecture featuring a WDM-based feeder network and a TDM-based distribution network. In this paper, we examine the design issues of the key constituent of SWE-PON (Scalable WDM-based Ethernet hybrid-PON) to validate its economic and practical feasibility. For flawless network operation, the wavelength tuning rule is investigated so that it does not collide between wavelengths from the tunable lasers belonging to the WDM coupler. Also, the potential problem between the tunable laser and the reflective operational device is analyzed in detail. From the numerical analysis and simulation, we demonstrate the variation of the network performance in terms of the upstream traffic delay and throughput of the ONU in accordance with the sharing structure of distribution network and the number of tunable laser devices (TLDs) at the feeder network.

Ultra-wideband impulse-radio systems have the ability to resolve multiple paths of the transmit radio and to mitigate the fading. Rake reception is capable of combining these paths, thereby improving the signal-to-noise ratio. In LOS channel, however, the improvement may be comparatively small for the cost of increasing receiver system complexity. This is because the LOS path should be dominant for the total energy in all paths. In this paper the distribution of the energy captured by Rake receiver is first presented for 160 measured LOS channel cases and then discussed. Rake reception with reflector is next suggested in order to effectively increase the signal energy without increasing the complexity, that is, increased number of Rake fingers. The use of reflector is also suggested for non-LOS channel and experimentally discussed where the Rake gain is compared with conventional Rake without reflector. The measurement results show the usefulness.