In this paper we propose a new far-field RCS prediction method using cylindrical or planar near-field RCS data. First we derive the relation between RCS and the scattering coefficient using physical optics technique. The far-field RCS prediction algorithm is obtained by approximating the relation using the condition of Fresnel region and the paraxial constraint of scanning angle in the case of cylindrical or planar scanning. Finally we predict the far-field RCS using measured or calculated near-field RCS data of the conducting rectangular prism or plate. The validity of the proposed algorithm is demonstrated.

A method is proposed for improving the accuracy of the characteristic basis function method (CBFM) using the multilevel approach. With this technique, CBFs taking into account multiple scattering calculated for each block (IP-CBFs; improved primary CBFs) are applied to CBFM using a multilevel approach. By using IP-CBFs, the interaction between blocks is taken into account, and thus it is possible to reduce the number of CBFs while maintaining accuracy, even if the multilevel approach is used. The radar cross section (RCS) of a cube, a cavity, and a dielectric sphere were analyzed using the proposed CBFs, and as a result it was found that accuracy is improved over the conventional method, despite no major change in the number of CBFs.

We propose a new, compact, center-fed reflector antenna that is capable of one-dimensional electronic beam scanning. The reflector profile in the vertical section (beam-scanning) is set to an imaging reflector configuration, while the profile in the orthogonal horizontal section (non-beam-scanning) is set to a Cassegrain antenna configuration. The primary radiator is a one-dimensional phased array antenna. We choose a center-fed configuration in order to reduce the antenna size as much as possible, despite the fact that the increased blocking area from the primary radiator causes degradation in efficiency compared to the typical offset-type configuration. In the proposed configuration, beam scanning is limited to one dimension, but utilize a compact, center-fed configuration that maintains the features of an imaging reflector antenna. We present the antenna configuration and design method and show that results obtained from the prototype antenna verify the predicted performance.

A novel approximate equivalent edge currents (EECs) are proposed for use in the modified edge representation (MER) for flat plates. It was reported that PO-EECs with classical PO diffraction coefficients, as applied to MER, perfectly recover PO surface integration. The inclusion of classical FW-EECs as it is, however, would not enhance the accuracy since the reality of the fringe wave is lost in the edge modification. This paper presents simple approximation for inclusion of FW-EECs in MER; FW-EECs are weighted by the function of the angle between the modified edge and the real edge. The key feature of this approach is that uniform fields are predicted everywhere though only classical diffraction coefficients are used. MER also simplifies the ray-tracing in the secondary diffraction analysis. Numerical results for diffraction from flat plates demonstrate the potential of these EECs.

The effects of finite ground plane upon the patterns of the GPS patch antennas are analyzed by EEC with modified edge representation (MER). The comparison with UTD and measurements shows that low elevation patterns including axial ratios are successfully predicted.

We investigate a phased array-fed dual reflector antenna applying one-dimensional beam-scanning of the center-fed type, using an elliptical aperture to provide wide area observation. The distinguishing feature of this antenna is its elliptical aperture shape, in which the aperture diameter differs between the forward satellite direction and the cross-section orthogonal to it. The shape in the plane of the forward satellite direction, which does not have a beam-scanning function, is a ring-focus Cassegrain antenna, and the shape in the plane orthogonal to that, which does have a beam-scanning function, is an imaging reflector antenna. This paper describes issues which arose during design of the elliptical aperture shape and how they were solved, and presents design results using elliptical aperture dimensions of 1600 mm × 600 mm, in which the beam width differs by more than two times in the orthogonal cross-section. The effectiveness of the antenna was verified by fabricating a prototype antenna based on the design results. Measurement results confirmed that an aperture efficiency of 50% or more could be achieved, and that a different beam width was obtained in the orthogonal plane in accordance with design values.

We propose a novel improved characteristic basis function method (IP-CBFM) for accurately analysing the radar cross section (RCS). This new IP-CBFM incorporates the effect of higher-order multiple scattering and has major influences in analyzing monostatic RCS (MRCS) of single incidence and bistatic RCS (BRCS) problems. We calculated the RCS of two scatterers and could confirm that the proposed IP-CBFM provided higher accuracy than the conventional method while significantly reducing the number of CBF.

The method for estimating propagation loss that classifies receiving points into multiple groups by focusing on the number of reflections and diffractions, and applies a separate statistical model to each group was extended from only 2.4 GHz band to both 2.4 GHz and 5 GHz band. The extended statistical model was created from received power measurements. First, an appropriate grouping method was investigated based on the fitting error of statistical model. Non-line-of-sight (NLOS) receiving points were grouped in order of points that a wave reflected one time reaches, points that a wave reflected two times reaches, and points that a wave diffracted one time reaches. Next, the effectiveness of the proposed method was verified by comparison with conventional statistical models (one-slope, dual-slope, multi-wall, partitioned) on three office floors that differ from the environment used to create the statistical model. The average NLOS estimation error for the three evaluation environments was 4.9 dB, demonstrating that the proposed method has accuracy equal to or better than that of conventional methods.

We present design procedures for using conducting wires in A-sandwich junctions to achieve high transmission performance; bench-test results validate the procedures. The scattering characteristics of the junction are obtained by solving the electric field integral equation of volumetric equivalent currents. The transmission performance is evaluated by subtracting the scattered fields of the same-sized A-sandwich panel in order to offset the effect of edge diffraction. Optimum wire width is determined by examining transmission performance with different arrangements. The designed junction achieves high transmission performance. The measured scattering characteristics of a bench model demonstrate the validity of the presented method.

We propose a novel phased array-fed dual-reflector antenna that reduces performance degradation caused by multiple reflection. The marked feature of the proposed configuration is that different reflector profiles are employed for the two orthogonal directions. The reflector profile in the beam-scanning section (vertical section) is set to an imaging reflector configuration, while the profile in the orthogonal non-beam-scanning section (horizontal section) is set to a ring-focus Cassegrain antenna configuration. In order to compare the proposed antenna with the conventional antenna in which multiple reflection was problematic, we designed a prototype antenna of the same size, and verified the validity of the proposed antenna. The results of the verification were that the gain in the designed central frequency increased by 0.4 dB, and the ripple of the gain frequency properties that was produced by multiple reflection was decreased by 1.1,dB. These results demonstrated the validity of the proposed antenna.

A design method is proposed for a low-profile dual-shaped reflector antenna for the mobile satellite communications. The antenna is required to be low-profile because of mount restrictions. However, reduction of its height generally causes degradation of antenna performance. Firstly, an initial low-profile reflector antenna with an elliptical aperture is designed by using Geometrical Optics (GO) shaping. Then a Physical Optics (PO) shaping technique is applied to optimize the gain and sidelobes including mitigation of undesired scattering. The developed design method provides highly accurate design procedure for electrically small reflector antennas. Fabrication and measurement of a prototype antenna support the theory.

Radar Cross Section (RCS) can be obtained from near-field data by using near-field to far-field RCS transformation methods. Phase errors in near-field data cause the degradation of the prediction accuracy. In order to overcome the difficulty, we propose the far-field RCS prediction method from one-dimensional intensity data in near-field. The proposed method is derived by extending the phase retrieval method based on the Gerchberg-Saxton algorithm with the use of the relational expression between near-fields and scattering coefficients. The far-field RCS can be predicted from the intensity data of scattered fields measured at two different ranges. The far-field RCS predicted by the proposed method approximately coincides with the computed one. The proposed method also has significant advantages of simple and efficient algorithm. The proposed method is valuable from a practical point of view.

Shaped beam reflector antennas are widely used because they can achieve a shaped beam even with a single primary feed. Because coverage shapes depend on service areas, optimum primary radiators and reflector shapes are determined by the service areas. In this paper, we propose a simultaneous optimal design method of the primary radiator and reflector for the shaped beam antenna. Particle swarm optimization and the conjugate gradient method are adopted to optimize the primary radiator and reflector. The design method is applied to Japan coverage to verify its effectiveness.

The authors propose the simple and efficient method based on the shooting and bouncing rays (SBR) method in order to evaluate multi-reflection effects inside a radome. In this paper, we show the analysis procedure of the proposed method. Next, we compare calculated data with some measured data in order to verify the proposed method. We confirmed that the proposed method is effective for the objects with radome except the areas where strong edge diffraction appears.

This paper presents the near-field to far-field transformation for an outdoor radar cross section (RCS) range. Direct measurement of the large actual target requires quite a long measurement range. The near-field to far-field RCS transformation method achieves the reduction of measurement range. However the non-uniformity of the incident electric field distribution on the target causes some errors in RCS prediction. We propose a novel near-field to far-field RCS transformation method that can be applied to an outdoor RCS measurement. The non-uniformity of the incident electric field distribution is successfully resolved by introducing the correction term of the ground bounce. We investigate the validity of the proposed method by the simulation and measurement.

The characteristic basis function method using improved primary characteristic basis functions (IP-CBFM) has been proposed as a technique for high-precision analysis of monostatic radar cross section (RCS) of a scattering field in a specific coordinate plane. IP-CBFM is a method which reduces the number of CBF necessary to express a current distribution by combining secondary CBF calculated for each block of the scatterer with the primary CBF to form a single improved primary CBF (IP-CBF). When the proposed technique was evaluated by calculating the monostatic RCS of a perfect electric conductor plate and cylinder, it was found that solutions corresponding well with analysis results from conventional CBFM can be obtained from small-scale matrix equations.

This paper proposes a novel quad-band branched monopole antenna with a filter. The proposed antenna has a simple configuration in which branch-elements are added to a basic configuration consisting of a mast and dielectric wires. The antenna is characterized by performances such as wideband impedance matching, gain stabilization, and gain enhancement. Wideband impedance characteristics satisfying the voltage standing ratio of less than 2 are obtained by exciting a parallel resonance at the lowest band and multi-resonance at high bands. The filter suppressing higher order modes is used for gain stabilization, so that averaged gains above 5dBi are obtained at the quad-band. The antenna has a high gain of 11.1dBi because the branch-elements work as an end-fire array antenna at the highest band. Furthermore, it is clarified that an operating frequency is switched by using a variable bandpass filter at the lowest band. Last, a scale model of the antenna is fabricated and measured, then the effectiveness of the proposed antenna is demonstrated.

A T-junction orthomode transducer (OMT) is a waveguide component that separates two orthogonal linear polarizations in the same frequency band. It has a common circular waveguide short-circuited at one end and two branch rectangular waveguides arranged in opposite directions near the short circuit. One of the advantages of a T-junction OMT is its short axial length. However, the two rectangular ports, which need to be orthogonal, have different levels of performance because of asymmetry. We therefore propose a uniaxially symmetrical T-junction OMT, which is configured such that the two branch waveguides are tilted 45° to the short circuit. The uniaxially symmetrical configuration enables same levels of performance for the two ports, and its impedance matching is easier compared to that for the conventional configuration. The polarization separation principle can be explained using the principles of orthomode junction (OMJ) and turnstile OMT. Based on calculations, the proposed configuration demonstrated a return loss of 25dB, XPD of 30dB, isolation of 21dB between the two branch ports, and loss of 0.25dB, with a bandwidth of 15% in the K band. The OMT was then fabricated as a single piece via 3D printing and evaluated against the calculated performance indices.

This study presents a novel waveguide slot array with a code-division multiplexing function for single RF chain digital beamforming. The proposed antenna is comprised of a rectangular metallic waveguide’s bottom part and a multilayer printed circuit board (PCB) with the rectangular waveguide’s top wall and slot apertures. Multiple pairs of two symmetric longitudinal slots are etched on the metal surface of the PCB, and a PIN diode is mounted across each slot. The received signals of each slot pair are multiplexed in a code-division multiplexing fashion by switching the diodes’ bias according to the Walsh Hadamard code, and the original signals are then recovered through a despreading process in the digital domain for digital beamforming. A prototype antenna with eight slot pairs has been fabricated and tested for proof of concept. The measured results show the feasibility of the proposed antenna.