Physics principles of a new type of microwave input amplifiers are described. Cyclotron wave electrostatic amplifier (CWESA) has a low noise level, broad band, switchable gain, super high self-protection against microwave overloads, rapid recovery and small DC consumption. CWESAs are widely used in Russian pulse Doppler radars and other systems.

A retrodirective system utilizing harmonic reradiation from a rectenna is developed and verified for long-range wireless power transfer applications, such as low-power or battery-less devices and lightweight aerial vehicles. The second harmonic generated by the rectifying circuit is used instead of a pilot signal, and thus an oscillator for creating the pilot signal is not required. The proposed retrodirective system consists of a 2.45 GHz transmitter with a two-element phased array antenna, a 4.9 GHz direction-of-arrival (DoA) estimation system, a phase control system, and a rectenna. The rectenna, consisting of a half-wave dipole antenna, receives microwave power from the 2.45 GHz transmitter and reradiates the harmonic toward the 4.9 GHz DoA estimation system. The rectenna characteristics and experimental demonstrations of the proposed retrodirective system are described. From measurement results, the dc output power pattern for the developed retrodirective system is in good agreement with that obtained using manual beam steering. The measured DoA estimation errors are within the range of -2.4° to 4.8°.

We developed a 5.8 GHz power-variable phase-controlled magnetron (PVPCM) which controls the phase of magnetron output by a phase shifter and controls the power by the anode current of the magnetron. This method is different from the previous 2.45 GHz phase-controlled magnetron which utilizes an injection method and a phase locked loop by the anode current, since the frequency of 5.8 GHz magnetron hardly changes with the anode current. Our experiments show that the developed 5.8 GHz PVPCM had a variable output power with 1% power stability from 160 W to 329 W, the phase accuracy was nearly ±1°, and the response time was less than 100 µs. Stable output power, high phase-controlled accuracy, and fast response speed microwave sources based on the PVPCMs are suitable for phased array system for wireless power transfer.

Perspectives of Cyclotron Wave Converter (CWC) of microwaves into DC are discussed in a form of short review. All main parts of CWC (microwave cavity, reverse region and collector) are analysed. Existing experimental results are briefly described.

In the beam-type microwave power transmission system, it is required to minimize the interference with communication and the influence on the human body. Retrodirective system that re-radiates a beam in the direction of arrival of a signal is well known as a beam control technique for accurate microwave power transmission. In this paper, we newly propose to apply the retrodirective system to both transmitting and receiving antennas. The leakage to the outside of the system is expected to minimize self-convergently while following the atmospheric fluctuation and the antenna movement by repeating the retrodirective between the transmitting and receiving antenna in this system. We considered this phenomenon theoretically using an infinite array antenna model. Finally, it has been shown by the equivalent circuit simulation that stable transmission can be realized by oscillating the system.

A simple, low reflection, and highly-efficient pilot-plant scale microwave irradiation reactor for woody biomass pretreatment was fabricated. Pretreatment is an essential process for effective bioethanol production. The fabricated reactor consists of 8 microwave irradiators which are attached to a metal pipe. The woody biomass mixture which contains water and organic acid flows through the metal pipe and is heated by microwaves at a total power of 12,kW. To design the microwave irradiators, we used a 3D Finite Element Method (FEM) simulator, which was based on the measured complex permittivity data of the woody biomass mixture. The simulation results showed that the reflection coefficient $|S_{11}|$ from the reactor was less than -30,dB when the woody biomass mixture temperature was between 30$^{circ}$C and 90$^{circ}$C. Finally, we experimentally confirmed that the fabricated irradiation reactor yielded a microwave absorption efficiency of 79%.

We developed a phase controlled magnetron (PCM) with high DC-RF conversion efficiency and with phase control to steer a microwave beam in order to realize the final space Solar Power Station (SPS) system. For the PCM, we use injection locking technique and PLL feedback to anode current. We can stabilize and control a frequency and a phase of a microwave of the PCM. However, we have a power loss after the PCM for the SPS use because of a size of the antenna (> km) and of a microwave power (> GW). In order to decrease power loss after PCM, we newly propose a concept of "sub phase shifter" which can change only 1 or 2 bits of a phase and has low loss. We can keep high beam collection efficiency when we control a beam to a twice larger direction in the SPS system. With this concept, we developed a PCM array called SPORTS (Space Power Radio Transmission System) in FY2000 and FY2001 in Kyoto University.

Microwave Power Transmission (MPT) technology is one of the most essential parts for Solar Power Station/Satellite (SPS). We study on application of magnetrons as DC-RF converters for the MPT transmitting system. Magnetrons cost much cheaper, have much higher DC-RF efficiency over 70% and much lighter system weight per 1 watt RF output than semiconductor amplifiers although they have wider bandwidth of the fundamental frequency and spurious noises in various frequencies. Spurious noises are radiated from the transmitting system and interfere in the other communication systems both in space and on the Earth. The objective of this study is the improvement of the spurious noises generated from magnetrons. Experimentally, magnetrons driven by DC stabilized power supply had not only narrower bandwidth of the fundamental frequency but also lower spurious noise levels when filament current is turned off than when it is turned on. Some spurious noises are probably caused by the intermodulation between the low frequency spurious noises, which frequency is below 1 GHz, and the fundamental or the harmonics. We also verified that the harmonics levels of the measured magnetron in our measurement system were below -70 dBc, which are comparable to or better than those of some semiconductor amplifiers, and that the harmonics were not improved greatly when the filament current was turned off because the source of the harmonics is the distortion of the fundamental.

A Cyclotron Wave Converter, having decreased magnetic intensity is discussed. Two microwave cavities with uniform and quadruple (or six-pole) electric field in the gap of interaction are used to transform microwave power into the kinetic power of the electron beam fast cyclotron wave. As a result of it, magnetic flux density occurs in two (or three) times lower. The latter is very important to create a compact, powerful and efficient microwave/DC power converters operating at different frequencies including short centimetric and long millimetric wavebands.

We discuss the division of radio resources in the time and frequency domains for wireless local area network (WLAN) devices powered with microwave energy. In general, there are two ways to avoid microwave power transmission (MPT) from influencing data communications: adjacent channel operation of continuous MPT and WLAN data transmission and co-channel operation of intermittent MPT and WLAN data transmission. Experimental results reveal that, even when we implement these methods, several problems arise because WLAN devices have been developed without supposing the existence of MPT. One problem clarified in our experiment is that adjacent channel operation at 2.4GHz does not necessarily perform well owing to the interference from MPT. This interference occurs regardless of the frequency separation at 2.4GHz. The other problem is that intermittent MPT could result in throughput degradation owing to the data rate control algorithm and the association scheme of the WLAN. In addition, the experimental results imply that a microwave energy source and a WLAN device should share information on the timings of intermittent MPT and data transmission to avoid buffer overflow.

The concept of placing enormous Solar Power Satellite (SPS) systems in space represents one of a handful of new technological options that might provide large scale, environmentally clean base load power to terrestrial markets. Recent advances in space exploration have shown a great need for antennas with high resolution, high gain and low side lobe level (SLL). The last characteristic is of paramount importance especially for the Microwave Power Transmission (MPT) in order to achieve higher transmitting efficiency (TE) and higher beam collection efficiency (BCE). In order to achieve low side lobe levels, statistical methods play an important role. Various interesting properties of a large antenna arrays with randomly, uniformly and combined spacing of elements have been studied, especially the relationship between the required number of elements and their appropriate spacing from one viewpoint and the desired SLL, the aperture dimension, the beamwidth and TE from the other. We propose a new unified approach in searching for reducing SLL by exploiting the interaction of deterministic and stochastic workspaces of proposed algorithms. Our models indicate the side lobe levels in a large area around the main beam and strongly reduce SLL in the entire visible range. A new concept of designing a large antenna array system is proposed. Our theoretic study and simulation results clarify how to deal with the problems of side lobes in designing a large antenna array, which seems to be an important step toward the realization of future SPS/MPT systems.

The Earth will require sustainable electricity sources equivalent to 3 to 5 times the commercial power presently produced by 2050. Solar Power Satellite (SPS) is one option for meeting the huge future energy demand. SPS can send enormous amounts of power to the Earth as the form of microwave (MW). A highly efficient microwave power transmission (MPT) system is needed for SPS. A critical goal of SPS is to maintain highest Beam Efficiency (BE) because the microwaves from SPS will be converted to utility power unlike the MW from communication satellites. Another critical goal of SPS is to maintain Side Lobe Levels (SLL) as small as possible to reduce interference to other communication systems. One way to decrease SLL and increase BE is the edge tapering of a phased array antenna. However, tapering the excitation requires a technically complicated system. Another way of achieving minimum SLL is with randomly spaced element position but it does not guarantee higher BE and the determination of random element position is also a difficult task. Isosceles Trapezoidal Distribution (ITD) edge tapered antenna was studied for SPS as an optimization between full edge tapering and uniform amplitude distribution. The highest Beam Collection Efficiency (BCE) and lowest SLL (except maximum SLL) are possible to achieve in ITD edge tapering and ITD edge tapered antenna is technically better. The performance of ITD is further improved from the perspective of both Maximum Side Lobe Level (MSLL) and BE by using unequal spacing of the antenna elements. A remarkable reduction in MSLL is achieved with ITD edge tapering with Unequal element spacing (ITDU). BE was also highest in ITDU. Determination of unequal element position for ITDU is very easy. ITDU is a newer concept that is experimented for the first time. The merits of ITDU over ITD and Gaussian edge tapering are discussed.

In this paper, we study the feasibility of a batteryless wireless sensor supplied with energy by using microwave power transmission (MPT). If we perform co-channel operation of MPT and wireless local area networks (WLANs) for the sake of spectral efficiency, a time division method for MPT and WLAN communications is required to avoid serious interference from MPT to WLAN data transmissions. In addition, to reduce the power consumption of a sensor, the use of power-save operation of the sensor is desirable. We proposed a scheduling scheme that allocates time for MPT and WLAN communications. Specifically, in the proposed scheduling system, an energy source transmits microwave power to a sensor station except when the sensor station transmits data frames or receives beacon frames. In addition, in the proposed scheduling system, we force the remaining energy of the sensor station to converge to a maximum value by adjusting the time interval of data transmission from the sensor station such that the power consumption of the sensor station is reduced. On the basis of the proposition, we implemented a scheduling system and then confirmed that it performed successfully in the conducted experiments. Finally, we discussed the feasibility of the proposed scheduling scheme by evaluating the coverage and then showed that the scheduling scheme can be applied to closed space or room.

In order to efficiently drive a low-power DC motor using microwave power transfer (MPT), a compact power-receiving device is developed, which consists of a rectenna array and an improved DC-DC converter with constant input resistance characteristics. Since the conversion efficiency of the rectenna is strongly affected by the output load, it is difficult to efficiently drive a dynamic load resistance device such as DC motor. Using both continuous-wave (CW) and pulsed-wave MPT, experiments are carried out on driving the DC motor whose load resistance is varying from 36 to 140 Ω. In the CW case, the measured overall efficiency of the power-receiving device is constant over 50% for the power density of 0.25 to 2.08 mW/cm2. In particular, the overall efficiency is 62%, 70.8% for the power density of 0.25, 0.98 mW/cm2 where the received power of the single antenna is 13, 50 mW, respectively. In the pulsed-wave case, the measured overall efficiency is over 44% for a duty ratio of 0.2 to 1 for the power density of 0.98 mW/cm2.

Drones have been attractive for many kinds of industries, but limited power supply from batteries has impeded drones from being operated for longer hours. Microwave power transmission (MPT) is one of the most prospective technologies to release them from the limitation. Since, among several types of drones, micro-drone has shorter available flight time, it is reasonable to provide micro-drone with wireless charging access with an MPT system. However, there is no suitable rectenna for micro-drone charging applications in preceding studies. In this paper, an MPT system for micro-drone was proposed at C-band where a lightweight and compact rectenna array with 20-W class output power was developed. Under illumination of a flat-top beam with 203 mW/cm2 of power density, a 16-element rectenna array was measured. The 16-element rectenna was formed with the aid of a honeycomb substrate for lightness and GaAs Schottky barrier diodes for high output. It was 37.5 g in weight and 146.4 mm by 146.4 mm in size. It output 27.0 W of dc power at 19.0 V at 5.8 GHz when radio frequency power of 280 W was generated by the injection-locked magnetron and 134 W was transmitted from the transmitting phased array. The power-to-weight ratio was 0.72W/g. The power conversion efficiency was 61.9%. These numbers outperformed the rectennas in the preceding studies and are suitable for an MPT system to micro-drone.

In this paper, we propose a novel radial line planar phased array in which helical antenna elements are individually rotated by their respective connected micromotors to realize dynamic beam-scanning. To our knowledge, this is the first radial line planar array (RLPA) that has antenna elements electromechanically rotated by their individual micromotors. To facilitate its fabrication, helix and its probe are directly metallized on a plastic shaft using molded interconnect device technology, and a motor shaft is press-fitted into the plastic shaft. We also present a new design methodology for RLPA, which combines the equivalent circuit theory and electromagnetic simulations of the unit cell element. The proposed procedure is practical to design an RLPA of antenna elements with arbitrary probe shape without large-scale full-wave analysis of the whole structure of the RLPA. We design, fabricate, and evaluate a 7-circle array with 168 helical antenna elements fabricated using molded interconnect device technology. The prototype antenna exhibits dynamic and accurate beam-scanning performance. Furthermore, the prototype antenna exhibits a low reflection coefficient (less than -17dB) and high antenna efficiency (above 77%), which validates the proposed design methodology.

This study proposes a new structure of a single-shunt rectifier circuit that can reduce circuit loss and improve efficiency over the conventional structure. The proposed structure can provide impedance matching to the measurement system (or receiving antenna) without the use of conventional matching circuits, such as stubs and tapers. The proposed structure can simultaneously perform full-wave rectification and impedance matching by placing a feeding point on the output filter's λ/4 transmission line. We use circuit simulation to compare the RF-DC conversion efficiency and circuit loss of the conventional and proposed structures. The simulation results show that the proposed structure has lower circuit loss and higher RF-DC conversion efficiency than the conventional structure. We fabricate the proposed rectifier circuit using a GaAs Schottky barrier diode. The simulation and measurement results show that the single-shunt rectifier circuit's proposed structure is capable of rectification and impedance matching. The fabricated rectifier circuit's RF-DC conversion efficiency reaches a maximum of 91.0%. This RF-DC conversion efficiency is a world record for 920-MHz band rectifier circuits.

This paper proposes a rate adaptation scheme (RAS) for a wireless local area network (WLAN) station powered with microwave power transmission (MPT). A WLAN station attempting to transmit data frames when exposed to microwave radiation for MPT, experiences a reduction in the physical (PHY) layer data rate because frames are lost even when the carrier sense mechanism is used. The key idea of the proposed scheme is to utilize the output of the rectenna used for receiving microwave power. Using rectenna output, a WLAN station based on the proposed scheme assesses whether the station is exposed to microwave radiation for MPT. Then, using historical data corresponding to the assessment result, the station selects an appropriate PHY data rate. The historical data are obtained from previous transmission results, e.g., historical data pertaining to the data frame loss ratio. The proposed scheme was implemented and verified through an experiment. Experimental results showed that the proposed scheme prevents the reduction in the PHY data rate, which is caused by the use of historical data stored in a single memory. Thus, the proposed scheme leads to an improvement in the WLAN throughput.

Minimizing the Side Lobe Level (SLL) and attain highest achievable Beam Collection Efficiency (BCE) is a critical goal for Solar Power Station/Satellite (SPS). If all antennas are uniformly excited then the main beam will carry only a part of the total energy due to the higher SLL. SLL is decreased and BCE is increased by adopting edge tapering for SPS. But edge tapering is a complex technical problem for SPS. So an optimization is needed between uniform amplitude distribution and edge tapering system. We have derived a new method of edge tapering called Isosceles Trapezoidal Distribution (ITD) edge tapering. Only a small number of antennas from each side of the phased array antenna are tapered in this method. ITD edge tapering is almost uniform so it is technically better. We have compared different amplitude distribution systems; uniform, Gaussian, Dolph-Chebyshev and the newly derived ITD method. The SLL reduction in ITD is even lower than those of other kinds of edge tapering. Therefore the amount of losing power in the SLL in ITD is lower. As a result the interference level becomes lower and BCE becomes higher in this method. The higher BCE and better SLL performance than those with uniform distribution can be achieved in ITD with phase error and under unit failed condition.

The high performance GaN power amplifier circuit operating at 7.1 GHz was demonstrated for potential use such as in a space ground station. First, the GaN HEMT chips were investigated for the high power amplifier circuit design. And next, the designed amplifier circuits matching with the load and source impedance of the non-linear models were fabricated. From measurement, the AB-class power amplifier circuit with the four-cell chip showed the power added efficiency (PAE) of 42.6% and output power with 41.7dBm at -3dB gain compression. Finally, the good performance of the power amplifier was confirmed in a 20-way radial power combiner with the PAE of 17.4% and output power of 52.6 dBm at -3dB gain compression.