Amir ZAIMBASHI Mohammad Reza TABAN Mohammad Mehdi NAYEBI
In Distributed detection systems, restricting the output of the local decision to one bit certainly implies a substantial information loss. In this paper, we consider the fuzzy detection, which uses a function called membership function for mapping the observation space of each local detector to a value between 0 and 1, indicating the degree of assurance about presence or absence of a signal. In this case, we examine the problem of distributed Maximum Likelihood (ML) and Order Statistic (OS) constant false alarm rate (CFAR) detections using fuzzy fusion rules such as "Algebraic Product"(AP), "Algebraic Sum"(AS), "Union"(Un) and "Intersection"(IS) in the fusion centre. For the Weibull clutter, the expression of the membership function based on the ML or OS CFAR processors in the local detectors is also obtained. For comparison, we consider a binary distributed detector, which uses the Maximum Likelihood and Algebraic Product (MLAP) or Order Statistic and Algebraic Product (OSAP) CFAR processors as the local detectors. In homogenous and non homogenous situations, multiple targets or clutter edge, the performances of the fuzzy and binary distributed detectors are analyzed and compared. The simulation results indicate the superior and robust performance of the distributed systems using fuzzy detection in the homogenous and non homogenous situations.
In this paper, a frequency transformation for designing polyphase transfer functions is proposed. A modification to the bilinear LP-LP transformation, which assigns both stopband edges on negative frequency range whereas passband edges are on positive one, results polyphase transfer functions. Design examples show validity of the proposed method.
Sarang KAZEMINIA Khayrollah HADIDI Abdollah KHOEI
This paper presents a new open-loop phase shifter and frequency synthesizer which can be implemented by small hardware. In the proposed method the differential square wave is converted to a differential ramp. Then the cross points of two ramps are detected as the middle points of high or low durations and are recovered to full digital levels, for 90shifting operation. 4-phases in 50 MHz frequency can be generated by 3.5 mW power consumption and 60 µm60 µm area. All circuits have been simulated in 0.35 µm CMOS technology.
In this paper, we propose a novel MAC protocol with the patterned preamble technique to improve performance in terms of low power, channel utilization, and delay in wireless sensor networks. B-MAC is one of typical MAC protocols for wireless sensor networks using the duty cycle in order to achieve low-power operation. Since it works in an asynchronous fashion, B-MAC employs extended preamble and preamble sampling techniques. Even if it has outstanding performance in idle state, the overhead of these techniques is very large when packets are sent and received, because there is a lot of waste in the traditional preamble method. Instead of the simple preamble, our proposed MAC solution is to introduce more intelligent preamble with some patterns consisting of 2 phases (Tx phase & Ack phase). With this concept we implement real source code working on the mica2 platform with Tinyos-1.x version. Also, the test set-up is presented, and the test results demonstrate that the proposed protocol provides better performance in terms of delay compared to B-MAC.
This paper presents a methodology for performing on-line voltage risk identification (VRI) in power supply networks using hyperrectangular composite neural networks (HRCNNs) and synchronized phasor measurements. The FHRCNN presented in this study integrates the paradigm of neural networks with the concept of knowledge-based approaches, rendering them both more useful than when applied alone. The fuzzy rules extracted from the dynamic data relating to the power system formalize the knowledge applied by experts when conducting the voltage risk assessment procedure. The efficiency of the proposed technique is demonstrated via its application to the Taiwan Power Provider System (Tai-Power System) under various operating conditions. Overall, the results indicated that the proposed scheme achieves a minimum 97 % success rate in determining the current voltage security level.
A rate control scheme is described for zero-forcing beamforming (ZFBF) multiuser multiple-input and multiple-output (MU-MIMO) systems with a QR-decomposition maximum likelihood detector (MLD) at the receiver. For selected users, a modulation-and-coding set is selected for each substream by estimating the per-substream post-MLD signal-to-interference-plus-noise ratio. Iterative modified QR-decomposition MLD is employed at the receiver to achieve the throughput expected from the transmitter. The simulation results demonstrated that the proposed rate-control scheme achieved the target packet error rate while increasing the throughout for ZFBF-MU-MIMO systems as the number of user candidates increases.
This paper introduces an adaptive low complexity pre-processing filter to improve the coding performance of seriously degraded video sequences that is caused by the additive noise. The additive noise leads to a decrease in coding performance due to the high frequency components. By incorporating local statistics and quantization parameter into filtering process, the spurious noise is significantly attenuated and coding efficiency is improved for given quantization step size. In order to reduce the complexity of the pre-processing filter, the simplified local statistics and quantization parameter are introduced. The simulation results show the capability of the proposed algorithm.
Gagik MKRTCHYAN Katsuhiro NAITO Kazuo MORI Hideo KOBAYASHI
Multi-carrier code division multiple access (MC-CDMA) has been considered as one of the promising techniques for the next generation of mobile communication systems because of its efficient bandwidth usage, robustness to the multi-path fading and simple channel-sharing scheme. However, MC-CDMA cannot be employed in the uplink communication where the transmitted signal from each user propagates through the different multi-path fading channel, and the received signals are no longer orthogonal at the base station. As a result, bit error rate (BER) performance in the uplink MC-CDMA communication would be strongly degraded due to the occurrence of multi-user interference (MUI). To solve the MUI problem in the uplink MC-CDMA, the pre-equalization method was proposed in which the uplink signal is pre-equalized at the user terminal by using the channel response estimated from the downlink. Although the pre-equalization method is very effective for the stationary uplink channel with fixed users, it is hard to be employed in the time varying fading channel with mobile users, because there is a big difference in the channel responses between downlink and uplink. For the efficient MUI compensation, each user terminal would be required to predict the future channel conditions based on the current observation. This paper proposes a method for model based uplink channel response prediction by employing the spectral decomposition of the downlink channel impulse response. Computer simulation results show that the proposed method can achieve the accurate prediction of channel response for mobile users during the uplink transmission and allows the effective MUI compensation.
Quoc Tuan TRAN Shinsuke HARA Kriangsak SIVASONDHIVAT Jun-ichi TAKADA Atsushi HONDA Yuuta NAKAYA Kaoru YOKOO Ichirou IDA Yasuyuki OISHI
The combination of Multiple-Input Multiple-Output (MIMO) and Orthogonal Frequency Division Multiplexing (OFDM) technologies gives wireless communications systems the advantages of lower bit error rate (BER) and higher data rate in frequency-selective fading environments. However, the main drawbacks of MIMO systems are their high complexity and high cost. Therefore, antenna selection in MIMO systems has been shown to be an effective way to overcome the drawbacks. In this paper, we propose two receive antenna selection methods for a MIMO-OFDM system with radio frequency (RF) switches and polarization antenna elements at the receiver side, taking into consideration low computational complexity. The first method selects a set of polarization antenna elements which gives lower correlation between received signals and larger received signal power, thus achieves a lower BER with low computational complexity. The second method first selects a set of polarization antenna elements based on the criterion of the first method and another set of polarization antenna elements based on the criterion of minimizing the correlation between the received signals; it then calculates the signal-to-interference-plus-noise power ratio (SINR) of the two sets and selects a set with larger SINR. As a result, the second method achieves a better BER than the first one but it also requires higher computational complexity than the first one. We use the measured channel data to evaluate the performance of the two methods and show that they work effectively for the realistic channel.
Chia-Chun TSAI Jan-Ou WU Trong-Yen LEE
This study has demonstrated that the clock tree construction in an SoC should be expanded to consider the intrinsic delay and skew of each IP's clock sink. A novel algorithm, called GDME, is proposed to combine grey relational clustering and DME approach for solving the problem of clock tree construction. Grey relational analysis can cluster the best pair of clock sinks and that guide a tapping point search for a DME algorithm for constructing a clock tree with zero skew and minimal delay. Experimentally, the proposed algorithm always obtains an RC- or RLC-based clock tree with zero skew and minimal delay for all the test cases and benchmarks. Experimental results demonstrate that the GDME improves up to 3.74% for total average in terms of total wire length compared with other DME algorithms. Furthermore, our results for the zero-skew RLC-based clock trees compared with Hspice are 0.017% and 0.2% lower for absolute average in terms of skew and delay, respectively.
Human's ability to perceive elevation of a sound and distinguish whether a sound is coming from the front or rear strongly depends on the monaural spectral features of the pinnae. In order to realize an effective virtual auditory display by HRTF (head-related transfer function) customization, the pinna responses were isolated from the median HRIRs (head-related impulse responses) of 45 individual HRIRs in the CIPIC HRTF database and modeled as linear combinations of 4 or 5 basic temporal shapes (basis functions) per each elevation on the median plane by PCA (principal components analysis) in the time domain. By tuning the weight of each basis function computed for a specific height to replace the pinna response in the KEMAR HRIR at the same height with the resulting customized pinna response and listening to the filtered stimuli over headphones, 4 individuals with normal hearing sensitivity were able to create a set of HRIRs that outperformed the KEMAR HRIRs in producing vertical effects with reduced front/back ambiguity in the median plane. Since the monaural spectral features of the pinnae are almost independent of azimuthal variation of the source direction, similar vertical effects could also be generated at different azimuthal directions simply by varying the ITD (interaural time difference) according to the direction as well as the size of each individual's own head.
Bagus SANTOSO Noboru KUNIHIRO Naoki KANAYAMA Kazuo OHTA
In this paper we propose an algorithm of factoring any integer N which has k different prime factors with the same bit-length, when about ()log2 N high-order bits of each prime factor are given. For a fixed ε, the running time of our algorithm is heuristic polynomial in (log2 N). Our factoring algorithm is based on a lattice-based algorithm of solving any k-variate polynomial equation over Z, which might be an independent interest.
We focus on the relationship between the linearization method and linear complexity and show that the linearization method is another effective technique for calculating linear complexity. We analyze its effectiveness by comparing with the logic circuit method. We compare the relevant conditions and necessary computational cost with those of the Berlekamp-Massey algorithm and the Games-Chan algorithm. The significant property of a linearization method is that it needs no output sequence from a pseudo-random number generator (PRNG) because it calculates linear complexity using the algebraic expression of its algorithm. When a PRNG has n [bit] stages (registers or internal states), the necessary computational cost is smaller than O(2n). On the other hand, the Berlekamp-Massey algorithm needs O(N2) where N ( 2n) denotes period. Since existing methods calculate using the output sequence, an initial value of PRNG influences a resultant value of linear complexity. Therefore, a linear complexity is generally given as an estimate value. On the other hand, a linearization method calculates from an algorithm of PRNG, it can determine the lower bound of linear complexity.
Sobia BAIG Muhammad Junaid MUGHAL
A novel Uniform Discrete Multitone (DMT) transceiver is proposed, utilizing a wavelet packet based filter bank transmultiplexer in conjunction with a DMT transceiver. The proposed transceiver decomposes the channel spectrum into subbands of equal bandwidth. The objective is to minimize the bit error rate (BER), which is increased by channel-noise amplification. This noise amplification is due to the Zero-Forcing equalization (ZFE) technique. Quantization of the channel-noise amplification is presented, based on post-equalization signal-to-noise ratio (SNR) and probability of error in all subbands of the Uniform DMT system. A modified power loading algorithm is applied to allocate variable power according to subband gains. A BER performance comparison of the Uniform DMT with variable and uniform power-loading and with a conventional DMT system in a Digital Subscriber Line (DSL) channel is presented.
Jong Yoon HWANG Kwang Soon KIM Yong-Seok KIM Keum-Chan WHANG
In this letter, a novel blind CFO estimation algorithm for the uplink of an OFDMA system is proposed. The proposed method exploits the inherent redundant information in OFDMA symbols and does not require additional pilot or preamble overhead. Since it is a post-FFT estimator, it does not use filter banks to separate the desired user's signal from the others in the time domain. Hence, the subcarriers of a certain user are not restricted to be clustered in the frequency domain. Therefore, the proposed estimator can be applied to OFDMA systems with an arbitrary subcarrier assignment over the entire bandwidth, including IEEE 802.16e, to obtain sufficient frequency diversity in a frequency selective fading channel. The proposed method can be efficiently used for continuous tracking of all active users' CFOs only with two FFT windows within a single OFDM symbol. From simulation results, the performance of the proposed scheme is shown better than that uses preamble symbols.
Shinichi FURUKAWA Wataru SATOU Takashi HINATA Nao SHIMIZU
In this paper, a fiber with two inhomogeneous sector holes around the core is proposed, and propagation characteristics of polarization maintaining region and single-polarization region are numerically analyzed by circular Fourier expansion method. In each case of the single-polarization region and the polarization maintaining region, a fiber is designed so as to satisfy the zero total dispersion at wavelength of 1.55 µm. Then, the single-polarization bandwidth for the single-polarization region and the modal birefringence for the polarization maintaining region are examined as the specific characteristics in each region. In addition, the power concentrating into the core region and distributions of Poynting vector is also discussed.
Junichi NAKAYAMA Yasuhiko TAMURA
A transverse magnetic (TM) plane wave is diffracted by a periodic surface into discrete directions. However, only the reflection and no diffraction take place when the angle of incidence becomes a low grazing limit. On the other hand, the scattering occurs even at such a limit, if the periodic surface is finite in extent. To solve such contradiction, this paper deals with the scattering from a perfectly conductive sinusoidal surface with finite extent. By the undersampling approximation introduced previously, the total scattering cross section is numerically calculated against the angle of incidence for several corrugation widths up to more than 104 times of wavelength. It is then found that the total scattering cross section is linearly proportional to the corrugation width in general. But an exception takes place at a low grazing limit of incidence, where the total scattering cross section increases almost proportional to the square root of the corrugation width. This suggests that, when the corrugation width goes to infinity, the total scattering cross section diverges and the total scattering cross section per unit surface vanishes at a low grazing limit of incidence. Then, it is concluded that, at a low grazing limit of incidence, no diffraction takes place by a periodic surface with infinite extent and the scattering occurs from a periodic surface with finite extent.
Soodesh BULJORE Markus MUCK Patricia MARTIGNE Paul HOUZE Hiroshi HARADA Kentaro ISHIZU Oliver HOLLAND Andrej MIHAILOVIC Kostas A. TSAGKARIS Oriol SALLENT Gary CLEMO Mahesh SOORIYABANDARA Vladimir IVANOV Klaus NOLTE Makis STAMETALOS
The Project Authorization Request (PAR) for the IEEE P1900.4 Working Group (WG), under the IEEE Standards Coordinating Committee 41 (SCC41) was approved in December 2006, leading to this WG being officially launched in February 2007 [1]. The scope of this standard is to devise a functional architecture comprising building blocks to enable coordinated network-device distributed decision making, with the goal of aiding the optimization of radio resource usage, including spectrum access control, in heterogeneous wireless access networks. This paper introduces the activities and work under progress in IEEE P1900.4, including its scope and purpose in Sects. 1 and 2, the reference usage scenarios where the standard would be applicable in Sect. 4, and its current system architecture in Sect. 5.
Chen-Chien HSU Tsung-Chi LU Heng-Chou CHEN
In this paper, an evolutionary approach is proposed to obtain a discrete-time state-space interval model for uncertain continuous-time systems having interval uncertainties. Based on a worst-case analysis, the problem to derive the discrete interval model is first formulated as multiple mono-objective optimization problems for matrix-value functions associated with the discrete system matrices, and subsequently optimized via a proposed genetic algorithm (GA) to obtain the lower and upper bounds of the entries in the system matrices. To show the effectiveness of the proposed approach, roots clustering of the characteristic equation of the obtained discrete interval model is illustrated for comparison with those obtained via existing methods.
Hiroyuki DEGUCHI Mikio TSUJI Hiroaki WATANABE
To obtain a broad circular-coverage beam with low sidelobe, this paper proposes optimization design based on the quadratic programming approach for circular horns. The desired excitation coefficients of higher-order modes are pre-determined and also evaluated by calculating universal radiation patterns. We show a design example of a multimode horn which has circular-coverage beam with low sidelobe level of about -30 dB. The effectiveness of the designed horn is discussed by evaluating VSWR and radiation characteristics in X-band numerically and experimentally.