1-8hit |
Yuki OSAKA Fumihiko ITO Daisuke IIDA Tetsuya MANABE
Mode-by-mode impulse responses, or spectral transfer matrix (STM) of birefringent fibers are measured by using linear optical sampling, with assist of polarization multiplexed probe pulse. By using the eigenvalue analysis of the STM, the differential mode delay and PMD vector of polarization-maintaining fiber are analyzed as a function of optical frequency over 1THz. We show that the amplitude averaging of the complex impulse responses is effective for enhancing the signal-to-noise ratio of the measurement, resulting in improving the accuracy and expanding the bandwidth of the measurement.
Wei LIAO Jingjing SHI Jianqing WANG
In this study, we propose a two-step approach to evaluate electromagnetic interference (EMI) with a wearable vital signal sensor. The two-step approach combines a quasi-static electromagnetic (EM) field analysis and an electric circuit analysis, and is applied to the EMI evaluation at frequencies below 1 MHz for our developed wearable electrocardiogram (ECG) to demonstrate its usefulness. The quasi-static EM field analysis gives the common mode voltage coupled from the incident EM field at the ECG sensing electrodes, and the electric circuit analysis quantifies a differential mode voltage at the differential amplifier output of the ECG detection circuit. The differential mode voltage has been shown to come from a conversion from the common mode voltage due to an imbalance between the contact impedances of the two sensing electrodes. When the contact impedance is resistive, the induced differential mode voltage increases with frequency up to 100kHz, and keeps constant after 100kHz, i.e., exhibits a high pass filter characteristic. While when the contact impedance is capacitive, the differential mode voltage exhibits a band pass filter characteristic with the maximum at frequency of around 150kHz. The differential voltage may achieve nearly 1V at the differential amplifier output for an imbalance of 30% under 10V/m plane-wave incident electric field, and completely mask the ECG signal. It is essential to reduce the imbalance as much as possible so as to prevent a significant interference voltage in the amplified ECG signal.
We present transmission- and reflection-type measurement methods for the differential mode delay (DMD) of a multimode optical fiber (MMF) optimized for high-speed local area networks (LANs) for the 850-nm band. Compared with a previously reported transmission-type measurement method for the 1550-nm wavelength band, we demonstrate here high-resolution DMD measurement methods for MMFs in the 850-nm band. As the method is based on a Fourier-domain intermodal interference technique, the measurement sensitivity is ∼60-dB, and it requires a fiber only a few meters in length. The shorter wavelength also allows a threefold improvement in the measurement resolution. The reflection-type measurement technique is a more practical than the transmission-type measurement technique for the field testing of short MMFs already installed in networks. We believe that this method will be a practical tool not only for field testing of short-length MMFs already installed in networks but also for the development of new plastic optical fibers (POFs).
Kyoung-Pyo AHN Ryo ISHIKAWA Kazuhiko HONJO
Different from distributed baluns, active baluns have group delay variations in the lower bands related to inherent internal capacitances and resistance in transistors. A negative group delay (NGD) circuit is employed as a compensator of group delay variation for an ultra-wideband (UWB) active balun. First, three-cell NGD circuit is inserted into a simple active balun circuit for realizing both group delay compensation and return loss improvement. The simulated results show a group delay variation of 4.8 ps and an input return loss of above 11.5 dB in the UWB band (3.1-10.6 GHz). Then, a pair of one-cell NGD circuits is added to reduce the remaining group delay variation (3.4 ps in simulation). The circuit with the NGD circuits was fabricated on an InGaP/GaAs HBT MMIC substrate. The measured results achieved a group delay variation of 7.7 ps, a gain variation of 0.5 dB, an input return loss of greater than 10 dB, and an output return loss of larger than 8.1 dB in the UWB band.
Kazushi MURAOKA Kazuhiko FUKAWA Hiroshi SUZUKI Satoshi SUYAMA
This paper proposes a new approach for the joint processing of signal detection and channel estimation based on the expectation-maximization (EM) algorithm in orthogonal frequency division multiplexing (OFDM) mobile communications. Conventional schemes based on the EM algorithm estimate a channel impulse response using Kalman filter, and employ the random walk model or the first-order autoregressive (AR) model to derive the process equation for the filter. Since these models assume that the time-variation of the impulse response is white noise without considering any autocorrelation property, the accuracy of the channel estimation deteriorates under fast-fading conditions, resulting in an increased packet error rate (PER). To improve the accuracy of the estimation of fast-fading channels, the proposed scheme employs a differential model that allows the correlated time-variation to be considered by introducing the first- and higher-order time differentials of the channel impulse response. In addition, this paper derives a forward recursive form of the channel estimation along both the frequency and time axes in order to reduce the computational complexity. Computer simulations of channels under fast multipath fading conditions demonstrate that the proposed method is superior in PER to the conventional schemes that employ the random walk model.
Akira SAITOU Kyoung-Pyo AHN Hajime AOKI Kazuhiko HONJO Koichi WATANABE
A design method for an ultra-wideband bandpass filter (BPF) with four coupled lines has been developed. For demonstration purposes, 50 Ω-matched self-complementary antennas integrated with the ultra-wideband, differential-mode BPF with four coupled lines, a notch filter, and a low-pass filter (LPF) were prepared and tested. An optimized structure for a single-stage, broadside-coupled and edge-coupled four-lines BPF was shown to exhibit up to 170% fractional bandwidth and an impedance transformation ratio of 1.2 with little bandwidth reduction, both analytically and experimentally. Using the optimized structure, 6-stage BPFs were designed to transform the self-complementary antenna's constant input impedance (60πεe- 1/2(Ω)) to 50 Ω without degrading bandwidth. In addition, two types of filter variations--a LPF-embedded BPF and a notch filter-embedded BPF--were designed and fabricated. The measured insertion loss of both filter systems was less than 2.6 dB over the ultra-wideband (UWB) band from 3.1 GHz to 10.6 GHz. The filter systems were embedded in the wideband self-complementary antennas to reject unnecessary radiation over the next pass band and 5-GHz wireless LAN band.
Ryuichi FUJIMOTO Chihiro YOSHINO Tetsuro ITAKURA
A simple modeling technique for symmetric inductors is proposed. Using the proposed technique, all model parameters for an equivalent circuit of symmetric inductors are easily calculated from geometric, process and substrate resistance parameters without using electromagnetic (EM) simulators. Comparison of simulated results with measured results verifies the effectiveness of the proposed modeling technique up to 5 GHz with center-tapped or non-center-tapped configurations.
Makoto TORIGOE Takuya MIYASHITA Osami WADA Ryuji KOGA Tetsushi WATANABE
The purpose of this report is to predict far-field EMI spectrum emitted from a signal line on a digital PCB based on near-field EMI measurement. The relation between near magnetic field and far electric field is shown. A method of predicting far electric field from near magnetic field is proposed. Current flowing along a signal line is calculated from measured near magnetic field. Far electric field is estimated from the current. Measurement and prediction of EM emission are carried out using a simple PCB. The result of prediction and measurement of far-field EMI spectrum coincide within the error of 3 dB.