In this paper, a passive multiple-input multiple-output (MIMO) radar system with widely separated antennas that estimates the positions and velocities of multiple moving targets by utilizing time delay (TD) and doppler shift (DS) measurements is proposed. Passive radar systems can detect targets by using multiple uncoordinated and un-synchronized illuminators and we assume that all the measurements including TD and DS have been known by a preprocessing method. In this study, the algorithm can be divided into three stages. First, based on location information within a certain range and utilizing the DBSCAN cluster algorithm we can obtain the initial position of each target. In the second stage according to the correlation between the TD measurements of each target in a specific receiver and the DSs, we can find the set of DS measurements for each target. Therefore, the initial speed estimated values can be obtained employing the least squares (LS) method. Finally, maximum likelihood (ML) estimation of a first-order Taylor expansion joint TD and DS is applied for a better solution. Extensive simulations show that the proposed algorithm has a good estimation performance and can achieve the Cramér-Rao lower bound (CRLB) under the condition of moderate measurement errors.

Millimeter wave (mmWave) massive Multiple-Input Multiple-Output (MIMO) systems generally adopt hybrid precoding combining digital and analog precoder as an alternative to full digital precoding to reduce RF chains and energy consumption. In order to balance the relationship between spectral efficiency, energy efficiency and hardware complexity, the hybrid-connected system structure should be adopted, and then the solution process of hybrid precoding can be simplified by decomposing the total achievable rate into several sub-rates. However, the singular value decomposition (SVD) incurs high complexity in calculating the optimal unconstrained hybrid precoder for each sub-rate. Therefore, this paper proposes PAST, a low complexity hybrid precoding algorithm based on projection approximate subspace tracking. The optimal unconstrained hybrid precoder of each sub-rate is estimated with the PAST algorithm, which avoids the high complexity process of calculating the left and right singular vectors and singular value matrix by SVD. Simulations demonstrate that PAST matches the spectral efficiency of SVD-based hybrid precoding in full-connected (FC), hybrid-connected (HC) and sub-connected (SC) system structure. Moreover, the superiority of PAST over SVD-based hybrid precoding in terms of complexity and increases with the number of transmitting antennas.

In recent years, there has been significant interest in information-theoretic security techniques that encrypt physical layer signals. We have proposed chaos modulation, which has both physical layer security and channel coding gain, as one such technique. In the chaos modulation method, the channel coding gain can be increased using a turbo mechanism that exchanges the log-likelihood ratio (LLR) with an external concatenated code using the max-log approximation. However, chaos modulation, which is a type of Gaussian modulation, does not use fixed mapping, and the distance between signal points is not constant; therefore, the accuracy of the max-log approximated LLR degrades under poor channel conditions. As a result, conventional methods suffer from performance degradation owing to error propagation in turbo decoding. Therefore, in this paper, we propose a new LLR clipping method that can be optimally applied to chaos modulation by limiting the confidence level of LLR and suppressing error propagation. For effective clipping on chaos modulation that does not have fixed mappings, the average confidence value is obtained from the extrinsic LLR calculated from the demodulator and decoder, and clipping is performed based on this value, either in the demodulator or the decoder. Numerical results indicated that the proposed method achieves the same performance as the one using the exact LLR, which requires complicated calculations. Furthermore, the security feature of the proposed system is evaluated, and we observe that sufficient security is provided.

This paper proposes a low-complexity variational Bayesian inference (VBI)-based method for massive multiple-input multiple-output (MIMO) downlink channel estimation. The temporal correlation at the mobile user side is jointly exploited to enhance the channel estimation performance. The key to the success of the proposed method is the column-independent factorization imposed in the VBI framework. Since we separate the Bayesian inference for each column vector of signal-of-interest, the computational complexity of the proposed method is significantly reduced. Moreover, the temporal correlation is automatically uncoupled to facilitate the updating rule derivation for the temporal correlation itself. Simulation results illustrate the substantial performance improvement achieved by the proposed method.

Expectation propagation (EP) is a powerful algorithm for signal recovery in compressed sensing. This letter proposes correction of a variance message before denoising to improve the performance of EP in the high signal-to-noise ratio (SNR) regime for finite-sized systems. The variance massage is replaced by an observation-dependent consistent estimator of the mean-square error in estimation before denoising. Massive multiple-input multiple-output (MIMO) is considered to verify the effectiveness of the proposed correction. Numerical simulations show that the proposed variance correction improves the high SNR performance of EP for massive MIMO with a few hundred transmit and receive antennas.

Sparse orthogonal matrices are proposed to improve the convergence property of expectation propagation (EP) for sparse signal recovery from compressed linear measurements subject to known dense and ill-conditioned multiplicative noise. As a typical problem, this letter addresses generalized spatial modulation (GSM) in over-loaded and spatially correlated multiple-input multiple-output (MIMO) systems. The proposed sparse orthogonal matrices are used in precoding and constructed efficiently via a generalization of the fast Walsh-Hadamard transform. Numerical simulations show that the proposed sparse orthogonal precoding improves the convergence property of EP in over-loaded GSM MIMO systems with known spatially correlated channel matrices.

This paper presents the excitation coefficient optimization of slot array antennas for increasing channel capacity in 2×2-mode two-dimensional ROM (rectangular coordinate orthogonal) transmission. Because the ROM transmission is for non-far region communication, the transmission between Tx (transmission) and Rx (reception) antennas increases when the antennas radiate beams inwardly. At first, we design the excitation coefficients of the slot arrays in order to enhance the transmission rate for a given transmission distance. Then, we fabricate monopulse corporate-feed waveguide slot array antennas that have the designed excitation amplitude and phase in the 60-GHz band for the 2×2-mode two-dimensional ROM transmission. The measured transmission between the fabricated Tx and Rx antennas increases at the given propagation distance and agrees with the simulation.

This paper proposes a hardware configuration for uplink multi-user multiple-input multiple-output (MU-MIMO) transmissions in a distributed antenna system (DAS). The demand for high-speed transmission in the uplink has increased recently, because of which standardizations in LTE-advanced and IEEE 802.11ax networks is currently underway. User terminal (UT) scheduling on the downlink MU-MIMO transmission is easy even in unlicensed band such as those in wireless local area network (WLAN) systems. However, the detailed management of the UTs is difficult on the uplink MU-MIMO transmissions because of the decentralized wireless access control. The proposed configuration allows an antenna to be selected from an external device on the access point (AP). All AP antennas are divided into groups, and the received signal in each group is input to the amplitude detector via a directional coupler. Subsequently, the selected antenna is fed by a multiple-to-one switch instead of a matrix switch. To clarify the effectiveness of the proposed configuration, we conduct computer simulations based on the ray-tracing method for propagation channels in an indoor environment.

The generalized spatial modulation (GSM) is a new transmission technique that can realize high-performance multiple-input multiple-output (MIMO) communication systems with a low RF complexity. This paper presents an efficient sphere decoding method used to perform the symbol detection for the generalized spatial modulation (GSM) multiple-input multiple-output (MIMO) systems. In the proposed method, the cost metric is modified so that it does not include the cancellation of the nonexistent interference. The modified cost metric can be computed by formulating a detection tree that has a regular structure representing the transmit antenna combinations as well as the symbol vectors, both of which are detected efficiently by finding the shortest path on the basis of an efficient tree search algorithm. As the tree search algorithm is performed for the regular detection tree to compute the modified but mathematically-equivalent cost metric, the efficiency of the sphere decoding is improved while the bit-error rate performance is not degraded. The simulation results show that the proposed method reduces the complexity significantly when compared with the previous method: for the 6×6 64QAM GSM-MIMO system with two active antennas, the average reduction rate of the complexity is as high as 45.8% in the count of the numerical operations.

In this paper, an improved lattice reduction (LR)-aided soft-output multiple-input multiple-output (MIMO) detector is proposed. Conventional LR-aided soft-output MIMO detectors involve the empty set problem (ESP), in which an entry with a particular bit in the candidate list might not exist. To overcome the performance degradation resulting from this ESP, a post-processing algorithm that modifies the candidate list is proposed. The proposed algorithm efficiently resolves the ESP by utilizing the near-orthogonality of the lattice-reduced system model so that the bit error rate (BER) performance is enhanced. In addition, as the complexity of the candidate list generation is reduced with the aid of the post-processing algorithm, the overall complexity is also reduced. Simulation results and the complexity comparisons demonstrate that our proposed method lowers the required Eb/No by 4-5 dB at the BER of 10-5 and the complexity by 13%-55%, compared to the conventional method.

This paper proposes performance improvement schemes for non-coherent multiple-input multiple-output (MIMO) communication systems employing per transmit antenna differential mapping (PADM). PADM is one form of differential space-time coding (DSTC), which generates an independent differentially encoded sequence for each of the multiple transmit antennas by means of space-time coding and mapping. The features of the proposed schemes are as follows: 1) it employs an asymmetric space-time mapping instead of the conventional symmetric space-time mapping in order to lower the required signal to noise power ratio (SNR) for maintaining the bit error rate (BER) performance; 2) it employs an analytically derived branch metric criterion based on channel prediction for per-survivor processing (PSP) in order to track fast time-varying channels. Finally, computer simulation results confirm that the proposed schemes improve the required SNR by around 1dB and can track at the maximum Doppler frequency normalized by symbol rate of 5%.

In this paper, we study the achievable degrees of freedom (DoF) of a multiple-input multiple-output (MIMO) multi-way relay channel with asymmetric message set that models the scenario of the two-way communication between a base station and multiple users through a relay. Under the assumption of delayed channel state information at transmitters (CSIT), we propose an amplify-and-forward relaying scheme based on the scheme proposed by Maddah-Ali and Tse to support signal space alignment, so that the available dimensions of the signal spaces at the relay and the users can be efficiently utilized. The proposed scheme outperforms the traditional one-way scheme from the perspective of DoF, and is useful to relieve the communication bottleneck caused by the asymmetric traffic load inherent in cellular networks.

Faster-than-Nyquist (FTN) signaling is investigated for quasi-static flat fading massive multiple-input multiple-output (MIMO) systems. In FTN signaling, pulse trains are sent at a symbol rate higher than the Nyquist rate to increase the transmission rate. As a result, inter-symbol interference occurs inevitably for flat fading channels. This paper assesses the information-theoretically achievable rate of MIMO FTN signaling based on the optimum joint equalization and multiuser detection. The replica method developed in statistical physics is used to evaluate the achievable rate in the large-system limit, where the dimensions of input and output signals tend to infinity at the same rate. An analytical expression of the achievable rate is derived for general modulation schemes in the large-system limit. It is shown that FTN signaling does not improve the channel capacity of massive MIMO systems, and that FTN signaling with quadrature phase-shift keying achieves the channel capacity for all signal-to-noise ratios as the symbol period tends to zero.

In this paper, an iterative robust minimum-mean square error (MMSE) receiver for space-time block coding (STBC) is proposed to mitigate the performance degradations caused by channel state information (CSI) errors. The proposed scheme estimates an instantaneous covariance matrix of the effective noise, which includes additive white Gaussian noise and the effect of CSI errors. For this estimation, multiple solution candidate vectors are selected based on the distances between the MMSE estimate of the solution and the constellation points, and their a-posteriori probabilities are utilized to execute the estimation of the covariance matrix. To improve the estimation accuracy, the estimated covariance matrix is updated iteratively. Simulation results show that proposed robust receiver achieves substantial performance gains in terms of bit error rates as compared to conventional receiver schemes under CSI errors.

This paper presents an adaptive interference-aware receiver for multiuser multiple-input multiple-output (MU-MIMO) downlink systems in wireless local area network (WLAN) systems. The MU-MIMO downlink technique is one of the key techniques that are newly applied to WLAN systems in order to support a very high throughput. However, the simultaneous communication of several users causes inter-user interference (IUI), which adversely affects receivers. Therefore, in order to prevent IUI, a precoding technique is defined at the transmitter based on feedback from the receiver. Unfortunately, however, the receiver still suffers from interference, because the precoding technique is prone to practical errors from the feedback quantization and subcarrier grouping scheme. Whereas ordinary detection schemes are available to mitigate such interference, such schemes are unsuitable because of their low performance or high computational complexity. In this paper, we propose an switching algorithm based on the norm ratio between an effective channel matrix for the desired signal and that of the interfering signals. Simulation results based on the IEEE 802.11ac standard show that the proposed algorithm can achieve near-optimal performance with a 70% reduction in computational complexity.

In this letter, we propose a lattice reduction (LR) aided joint precoding design for MIMO-relay broadcast communication with the average bit error rate (BER) criterion. We jointly design the signal process flow at both the base station (BS), and the relay station (RS), using the reduced basis of two-stage channel matrices. We further modify the basic precoding design with a novel shift method and a modulo method to improve the power efficiency at the BS and the RS respectively. In addition, the MMSE-SIC algorithm is employed to improve the performance of precoding. Simulations show that, the proposed schemes achieve higher diversity order than the traditional precoding without LR, and the modified schemes significantly outperform the basic design, proving the effectiveness of the proposed methods.

The feasibility condition of interference alignment (IA) for multiple-input multiple-output two-way interference channel is studied in this paper. A necessary condition and a sufficient condition on the IA feasibility are established and the sum degrees of freedom (DoF) for a broad class of network topologies is characterized. The numerical results demonstrate that two-way operation with appropriate IA is able to achieve larger sum DoF than the conventional one-way operation.

This paper presents a codeword metric calculation scheme for two step joint decoding of block coded signals in overloaded multiple-input multiple-output (MIMO) orthogonal frequency division multiplexing (OFDM) systems. A two step joint decoding scheme has been proposed for the complexity reduction as compared to joint maximum likelihood decoding in overloaded MIMO systems. Outer codes are widely used in wireless LANs such as IEEE802.11n. However, the two step joint decoding has not been combined with an outer code. In the first step of the two step joint decoding candidate codewords for metric calculation in the second step are selected. The selection of the candidate codewords in the inner block code may not always be able to provide the metric of a binary coded symbol for the outer code. Moreover, a bit flipping based codeword selection scheme in the two step joint decoding may not always provide the second best candidate codeword. Thus, in the proposed scheme the metric of the binary coded symbol calculated in the first step is reused in the second step of two step joint decoding. It is shown that the two step joint decoding with the proposed metric calculation scheme achieves better performance than that of the joint decoding with the bit flipping based codeword calculation scheme and reduces the complexity by about 0.013 for 4 signal streams with the cost of bit error rate degradation within 0.5dB.

This paper proposes a novel iterative multiple-input multiple-output (MIMO) receiver for orthogonal frequency division multiplexing (OFDM) systems, named as an “iterative MIMO receiver employing virtual channels with a Turbo decoder.” The proposed MIMO receiver comprises a MIMO detector with virtual channel detection and a Turbo decoder, between which signals are exchanged iteratively. This paper proposes a semi hard input soft output (SHISO) iterative decoding for the iterative MIMO receiver that achieves better performance than a soft input soft output (SISO) iterative decoding. Moreover, this paper proposes a new criterion for the MIMO detector to select the most likely virtual channel. The performance of the proposed receiver is verified in a 6×2 MIMO-OFDM system by computer simulation. The proposed receiver achieves better performance than the SISO MAP iterative receiver by 1.5dB at the bit error rate (BER) of 10-4, by optimizing the number of the Turbo iteration per the SHISO iteration. Moreover, the proposed detection criterion enables the proposed receiver to achieve a gain of 3.0dB at the BER of 10-5, compared with the SISO MAP iterative receiver with the Turbo decoder.

Implicit feedback is an approach that utilizes uplink channel state information (CSI) for downlink transmit beamforming on multiple-input multiple-output (MIMO) systems, relying on over-the-air channel reciprocity. The implicit feedback improves throughput efficiency because overhead of CSI feedback for change of over-the-air channel responses is omitted. However, it is necessary for the implicit feedback to calibrate circuitry responses that uplink CSI includes, because actual downlink and uplink channel responses do not match due to different transmit and receive circuitry chains. This paper presents our proposed calibration scheme, weighted-combining calibration (WCC); it offers improved calibration accuracy. In WCC, an access point (AP) calculates multiple calibration coefficients from ratios of downlink and uplink CSI, and then combines coefficients with minimum mean square error (MMSE) weights. The weights are derived using a linear approximation in the high signal to noise power ratio (SNR) regime. Analytical mean square error (MSE) of calibration coefficients with WCC and calibration schemes for comparison is expressed based on the linear approximation. Computer simulations show that the analytical MSE matches simulated one if the linear approximation holds, and that WCC improves the MSE and signal to interference plus noise power ratio (SINR). Indoor experiments are performed on a multiuser MIMO system with implicit feedback based on orthogonal frequency division multiplexing (OFDM), built using measurement hardware. Experimental results verify that the channel reciprocity can be exploited on the developed multiuser MIMO-OFDM system and that WCC is also effective in indoor environments.