This study introduces a novel single-diode rectenna, enhancing the rf-dc conversion efficiency using harmonic control of the antenna impedance. We employ source-pull simulations encompassing the fundamental frequency and the harmonics to achieve a highly efficient rectenna. The results of the source-pull simulations delineate the source-impedance ranges required for enhanced efficiency at each harmonic. Based on the source-pull simulation results, we designed two inverted-F antenna with input impedances within and without these identified source impedance ranges. Experimental results show that the proposed rectenna has a maximum rf-dc conversion efficiency of 75.9% at the fundamental frequency of 920 MHz, an input power of 10.8 dBm, and a load resistance of 1 kΩ, which is higher than that of the comparative rectenna without harmonic control of the antenna impedance. This study demonstrates that the proposed rectenna achieves high efficiency through the direct connection of the antenna and the single diode, along with harmonic control of the antenna impedance.

In this paper, a high-efficiency high-power rectenna with a bridge diode and the diode on antenna (DoA) topology is discussed. First, the topologies of rectifiers and rectennas are discussed to indicate the direction for obtaining highly efficient rectification. Rectifiers with well-matched diode pairs, as double voltage and bridge rectifiers, can reactively terminate even order harmonics, and is suitable for highly efficient operation. A rectenna with the DoA topology is suitable for a direct connection between the highly functional antenna and the rectifier diodes to remove lossy circuit portions. Next, the formulas for the rectification efficiency of the bridge rectifier are demonstrated with the behavioral model. The indicated formulas clarify the fundamental limitation on the rectification efficiency, which is the design goal in case of the DoA topology. Finally, we demonstrate a 5.8 GHz band 1 W rectenna with the bridge diode and the DoA topology. The bridge rectifier that is directly connected to the inductive high-impedance antenna achieved a rectification efficiency of 92.8% at an input power of 1 W. This is close to the fundamental limitation due to the diode performance.

Drones have been attractive for many kinds of industries, but limited power supply from batteries has impeded drones from being operated for longer hours. Microwave power transmission (MPT) is one of the most prospective technologies to release them from the limitation. Since, among several types of drones, micro-drone has shorter available flight time, it is reasonable to provide micro-drone with wireless charging access with an MPT system. However, there is no suitable rectenna for micro-drone charging applications in preceding studies. In this paper, an MPT system for micro-drone was proposed at C-band where a lightweight and compact rectenna array with 20-W class output power was developed. Under illumination of a flat-top beam with 203 mW/cm2 of power density, a 16-element rectenna array was measured. The 16-element rectenna was formed with the aid of a honeycomb substrate for lightness and GaAs Schottky barrier diodes for high output. It was 37.5 g in weight and 146.4 mm by 146.4 mm in size. It output 27.0 W of dc power at 19.0 V at 5.8 GHz when radio frequency power of 280 W was generated by the injection-locked magnetron and 134 W was transmitted from the transmitting phased array. The power-to-weight ratio was 0.72W/g. The power conversion efficiency was 61.9%. These numbers outperformed the rectennas in the preceding studies and are suitable for an MPT system to micro-drone.

A retrodirective system utilizing harmonic reradiation from a rectenna is developed and verified for long-range wireless power transfer applications, such as low-power or battery-less devices and lightweight aerial vehicles. The second harmonic generated by the rectifying circuit is used instead of a pilot signal, and thus an oscillator for creating the pilot signal is not required. The proposed retrodirective system consists of a 2.45 GHz transmitter with a two-element phased array antenna, a 4.9 GHz direction-of-arrival (DoA) estimation system, a phase control system, and a rectenna. The rectenna, consisting of a half-wave dipole antenna, receives microwave power from the 2.45 GHz transmitter and reradiates the harmonic toward the 4.9 GHz DoA estimation system. The rectenna characteristics and experimental demonstrations of the proposed retrodirective system are described. From measurement results, the dc output power pattern for the developed retrodirective system is in good agreement with that obtained using manual beam steering. The measured DoA estimation errors are within the range of -2.4° to 4.8°.

This paper proposes a rate adaptation scheme (RAS) for a wireless local area network (WLAN) station powered with microwave power transmission (MPT). A WLAN station attempting to transmit data frames when exposed to microwave radiation for MPT, experiences a reduction in the physical (PHY) layer data rate because frames are lost even when the carrier sense mechanism is used. The key idea of the proposed scheme is to utilize the output of the rectenna used for receiving microwave power. Using rectenna output, a WLAN station based on the proposed scheme assesses whether the station is exposed to microwave radiation for MPT. Then, using historical data corresponding to the assessment result, the station selects an appropriate PHY data rate. The historical data are obtained from previous transmission results, e.g., historical data pertaining to the data frame loss ratio. The proposed scheme was implemented and verified through an experiment. Experimental results showed that the proposed scheme prevents the reduction in the PHY data rate, which is caused by the use of historical data stored in a single memory. Thus, the proposed scheme leads to an improvement in the WLAN throughput.

This work addresses two key topics in the field of energy harvesting and wireless power transfer. The first is the optimum signal design for improved RF-DC conversion efficiency in rectifier circuits by using time varying envelope signals. The second is the design of rectifiers that present reduced sensitivity to input power and output load variations by introducing resistance compression network (RCN) structures.

In order to efficiently drive a low-power DC motor using microwave power transfer (MPT), a compact power-receiving device is developed, which consists of a rectenna array and an improved DC-DC converter with constant input resistance characteristics. Since the conversion efficiency of the rectenna is strongly affected by the output load, it is difficult to efficiently drive a dynamic load resistance device such as DC motor. Using both continuous-wave (CW) and pulsed-wave MPT, experiments are carried out on driving the DC motor whose load resistance is varying from 36 to 140 Ω. In the CW case, the measured overall efficiency of the power-receiving device is constant over 50% for the power density of 0.25 to 2.08 mW/cm2. In particular, the overall efficiency is 62%, 70.8% for the power density of 0.25, 0.98 mW/cm2 where the received power of the single antenna is 13, 50 mW, respectively. In the pulsed-wave case, the measured overall efficiency is over 44% for a duty ratio of 0.2 to 1 for the power density of 0.98 mW/cm2.

Microwaves have typically been used for communications and radar, but nowadays are given much attention to energy transfer applications. This paper describes microwave power transfer from a satellite to Earth that is visualized as a solar power satellite system (SPSS). After the system configuration is explained, unique engineering features are presented. Then, some contributions made by Japanese community are introduced, focusing on microwave and antenna engineering. As SPSS will handle high power levels at microwave frequency, and so components should be mass-produced to reduce the cost, then we need to shift our paradigm on the technology involved. Finally, the roadmap to a commercial SPSS is discussed.

A rectifying antenna is one of the most important components for wireless power transmission applications. In our previous papers, some RF-DC conversion circuits with high conversion efficiency at low input power are proposed. However, these RF-DC conversion circuits have some parts of which size depends on operating frequency, so the circuit size becomes large at low operating frequency. And, the composition of these RF-DC conversion circuits is complicated. Therefore, in this paper, a new RF-DC conversion circuit composed of only chip devices is proposed. This circuit has higher conversion efficiency than the previously proposed circuits. And, size reduction of the RF-DC conversion circuit is realized. Moreover, the composition of the circuit is simple, so the circuit size does not depend on operating frequency. For design of the RF-DC conversion circuits, LE-FDTD method is used. The measurement results agree with analytical results of the LE-FDTD method very well, and availability of the LE-FDTD method is discovered. It is shown that LE-FDTD method is a powerful analytical way which can give efficient design of RF-DC conversion circuit with high conversion efficiency.

A simple self-biased receiver system with a dual branch architecture consisting of a low-power consumption receiver and a rectenna is introduced. The system is efficiently integrated with a dual-fed circular sector antenna with harmonic rejection characteristics without a BPF. The receiver portion is designed by utilizing a low-noise amplifier (LNA) with low power consumption and a self-heterodyne mixer, while the rectenna achieves high conversion efficiency up to 80%, thanks to the harmonic rejection of the circular sector antenna. The rectified DC power from the rectenna is applied for a bias of the receiver without any external bias. Simultaneously, an ASK digital signal demodulation without an extra power supply are implemented successfully.

Results of a DC motor driving test with a power sent by a microwave and extracted with a rectenna array are reported. No significant difference has been observed in the output DC power from the rectenna array between a motor load and a resistive load. Mechanical output could be extracted from the received microwave power with an efficiency of 26%.

A rectenna element applicable to Stratosphere Radio Relay System was proposed and a fundamental microwave power transmission experiment was carried out at 2.45GHz using a rectenna array manufactured based on the proposal. The rectenna element consists of a circular microstrip patch and a rectifying circuit of novel balanced-type design. The circuit allows to mount a rectifier and circuit components just on one side of a substrate without through holes, and hence it must be easy to manufacture a rectenna even having a large aperture. It was verified by a preliminary experiment that the rectifying circuit can provide more than 1 W of DC output power using 8 Shottky diodes as a rectifier with microwave-DC conversion efficiency of 67%. Then, DC output power of 4W was obtained from the 4-element rectenna array in the microwave power transmission experiment carried out in a radio anechoic chamber. The data showed a feasibility of practical application of the microwave power transmission technique.