As a potential member of next generation wireless communications, the reconfigurable intelligent surface (RIS) can control the reflected elements to adjust the phase of the transmitted signal with less energy consumption. A novel RIS-assisted index modulation scheme is proposed in this paper, which is named the generalized reflected phase modulation (GRPM). In the GRPM, the transmitted bits are mapped into the reflected phase combination which is conveyed through the reflected elements on the RIS, and detected by the maximum likelihood (ML) detector. The performance analysis of the GRPM with the ML detector is presented, in which the closed form expression of pairwise error probability is derived. The simulation results show the bit error rate (BER) performance of GRPM by comparing with various RIS-assisted index modulation schemes in the conditions of various spectral efficiency and number of antennas.

Measurements of contact discharge current waveforms from an ESD generator with a test voltage of 4kV are conducted with the IEC specified arrangement of a 2m long return current cable in different three calibration environments that all comply with the IEC calibration standard to identify the occurrence source of damped oscillations (ringing), which has remained unclear since contact discharge testing was first adopted in 1989 IEC publication 801-2. Their frequency spectra are analyzed comparing with the spectrum calculated from the ideal contact discharge current waveform without ringing (IEC specified waveform) offered in IEC 61000-4-2 and the spectra derived from a simplified equivalent circuit based on the IEC standard in combination with the measured input impedances of one-ended grounding return current cable with the same arrangement in the same calibration environment as those for the current measurements. The results show that the measured contact discharge waveforms have ringing around the IEC specified waveform after the falling edge of the peak, causing their spectra from 20MHz to 200MHz, but the spectra from 40MHz to 200MHz significantly differ depending on the calibration environments even for the same cable arrangement, which do not almost affect the spectra from 20MHz to 40MHz and over 200MHz. In the calibration environment under the cable arrangement close to the reference ground, the spectral shapes of the measured contact discharge currents and their frequencies of the multiple peaks and dips roughly correspond to the spectral distributions calculated from the simplified equivalent circuit using the measured cable input impedances. These findings reveal that the root cause of ringing is mainly due to the resonances of the return current cable, and calibration environment under the cable arrangement away from the reference ground tends to mitigate the cable resonances.

To achieve the extreme high data rate and extreme coverage extension requirements of 6G wireless communication, new spectrum in sub-THz (100-300GHz) and non-terrestrial network (NTN) are two of the macro trends of 6G candidate technologies, respectively. However, non-linearity of power amplifiers (PA) is a critical challenge for both sub-THz and NTN. Therefore, high power efficiency (PE) or low peak to average power ratio (PAPR) waveform design becomes one of the most significant 6G research topics. Meanwhile, high spectral efficiency (SE) and low out-of-band emission (OOBE) are still important key performance indicators (KPIs) for 6G waveform design. Single-carrier waveform discrete Fourier transform spreading orthogonal frequency division multiplexing (DFT-s-OFDM) has achieved many research interests due to its high PE, and it has been supported in 5G New Radio (NR) when uplink coverage is limited. So DFT-s-OFDM can be regarded as a candidate waveform for 6G. Many enhancement schemes based on DFT-s-OFDM have been proposed, including null cyclic prefix (NCP)/unique word (UW), frequency-domain spectral shaping (FDSS), and time-domain compression and expansion (TD-CE), etc. However, there is no unified framework to be compatible with all the enhancement schemes. This paper firstly provides a general description of the 6G candidate waveforms based on DFT-s-OFDM enhancement. Secondly, the more flexible TD-CE supporting methods for unified non-orthogonal waveform (uNOW) are proposed and discussed. Thirdly, a unified waveform framework based on DFT-s-OFDM structure is proposed. By designing the pre-processing and post-processing modules before and after DFT in the unified waveform framework, the three technical methods (NCP/UW, FDSS, and TD-CE) can be integrated to improve three KPIs of DFT-s-OFDM simultaneously with high flexibility. Then the implementation complexity of the 6G candidate waveforms are analyzed and compared. Performance of different DFT-s-OFDM enhancement schemes is investigated by link level simulation, which reveals that uNOW can achieve the best PAPR performance among all the 6G candidate waveforms. When considering PA back-off, uNOW can achieve 124% throughput gain compared to traditional DFT-s-OFDM.

We discuss the spectral efficiency of orthogonal frequency-division multiplexing (OFDM) signals widely adopted in practical systems from a viewpoint of their power spectral density property. Since the conventional OFDM does not make use of pulse shaping filter, its out-of-band (OOB) spectrum may not be negligible especially when the number of subcarriers is small. Thus, in practice, windowing is applied to mitigate OOB emission by smoothing the transition of consecutive OFDM symbols, but its effectiveness has not been well investigated. Furthermore, OFDM signal suffers from nonlinear distortion associated with its high signal peak-to-average power ratio (PAPR), which also leads to OOB radiation. We examine how power amplifier nonlinearity affects the spectral efficiency based on the theoretical results developed in the literature.

In this study, the bending losses of chalcogenide glass channel optical waveguides consisting of an As2Se3 core and an As2S3 lower cladding layer were numerically evaluated across the astronomical N-band, which is the mid-infrared spectral range between the 8 µm and 12 µm wavelengths. The results reveal the design rules for bent waveguides in mid-infrared astrophotonic devices.

The altered fingerprints help criminals escape from police and cause great harm to the society. In this letter, an altered fingerprint detection method is proposed. The method is constructed by two deep convolutional neural networks to train the time-domain and frequency-domain features. A spectral attention module is added to connect two networks. After the extraction network, a feature fusion module is then used to exploit relationship of two network features. We make ablation experiments and add the module proposed in some popular architectures. Results show the proposed method can improve the performance of altered fingerprint detection compared with the recent neural networks.

To solve the problem of metamerism in the color reproduction process, various spectral reflectance reconstruction methods combined with neural network have been proposed in recent years. However, these methods are generally sensitive to initial values and can easily converge to local optimal solutions, especially on small data sets. In this paper, we propose a spectral reflectance reconstruction algorithm based on the Back Propagation Neural Network (BPNN) and an improved Sparrow Search Algorithm (SSA). In this algorithm, to solve the problem that BPNN is sensitive to initial values, we propose to use SSA to initialize BPNN, and we use the sine chaotic mapping to further improve the stability of the algorithm. In the experiment, we tested the proposed algorithm on the X-Rite ColorChecker Classic Mini Chart which contains 24 colors, the results show that the proposed algorithm has significantly better performance compared to other algorithms and moreover it can meet the needs of spectral reflectance reconstruction on small data sets. Code is avaible at https://github.com/LuraZhang/spectral-reflectance-reconsctuction.

The energy efficiency of intelligent reflecting surface (IRS) enabled internet of things (IoT) networks is studied in this letter. The energy efficiency is mathematically expressed, respectively, as the number of reflecting elements and the spectral efficiency of the network and is shown to scale in the logarithm of the reflecting elements number in the high regime of transmit power from source node. Furthermore, it is revealed that the energy efficiency scales linearly over the spectral efficiency in the high regime of transmit power, in contrast to conventional studies on energy and spectral efficiency trade-offs in the non-IRS wireless IoT networks. Numerical simulations are carried out to verify the derived results for the IRS enabled IoT networks.

Coprime (pair of) DFT filter banks (coprime DFTFB), which process signals like a spectral analyzer in time domain, divides the power spectrum equally into MN bands by employing two DFT filter banks (DFTFBs) of size only M and N respectively, where M and N are coprime integers. With coprime DFTFB, frequencies in wide sense stationary (WSS) signals can be effectively estimated with a much lower sampling rates than the Nyquist rates. However, the imperfection of practical FIR filter and the correlation based detection mode give rise to two kinds of spurious peaks in power spectrum estimation, that greatly limit the application of coprime DFTFB. Through detailed analysis of the spurious peaks, this paper proposes a modified spectral analyzer based on dual coprime DFTFBs and sub-decimation, which not only depresses the spurious peaks, but also improves the frequency estimation accuracy. The mathematical principle proof of the proposed spectral analyzer is also provided. In discussion of simultaneous signals detection, an O-extended MN-band coprime DFTFB (OExt M-N coprime DFTFB) structure is naturally deduced, where M, N, and O are coprime with each other. The original MN-band coprime DFTFB (M-N coprime DFTFB) can be seen a special case of the OExt M-N coprime DFTFB with extending factor O equals ‘1’. In the numerical simulation section, BPSK signals with random carrier frequencies are employed to test the proposed spectral analyzer. The results of detection probability versus SNR curves through 1000 Monte Carlo experiments verify the effectiveness of the proposed spectrum analyzer.

Water detection is important for machine vision applications such as visual inspection and robot motion planning. In this paper, we propose an approach to per-pixel water detection on unknown surfaces with a hyperspectral image. Our proposed method is based on the water spectral characteristics: water is transparent for visible light but translucent/opaque for near-infrared light and therefore the apparent near-infrared spectral reflectance of a surface is smaller than the original one when water is present on it. Specifically, we use a linear combination of a small number of basis vector to approximate the spectral reflectance and estimate the original near-infrared reflectance from the visible reflectance (which does not depend on the presence or absence of water) to detect water. We conducted a number of experiments using real images and show that our method, which estimates near-infrared spectral reflectance based on the visible spectral reflectance, has better performance than existing techniques.

In this study, we conduct guided mode analyses for chalcogenide glass channel waveguides using As2Se3 core and As2S3 lower cladding to determine their single-mode conditions across the astronomical N-band (8-12µm). The results reveal that a single-mode operation over the band can be achieved by choosing a suitable core-thickness.

This paper proposes two high-fidelity and computationally efficient neural voice conversion (VC) methods based on a direct waveform modification using spectral differentials. The conventional spectral-differential VC method with a minimum-phase filter achieves high-quality conversion for narrow-band (16 kHz-sampled) VC but requires heavy computational cost in filtering. This is because the minimum phase obtained using a fixed lifter of the Hilbert transform often results in a long-tap filter. Furthermore, when we extend the method to full-band (48 kHz-sampled) VC, the computational cost is heavy due to increased sampling points, and the converted-speech quality degrades due to large fluctuations in the high-frequency band. To construct a short-tap filter, we propose a lifter-training method for data-driven phase reconstruction that trains a lifter of the Hilbert transform by taking into account filter truncation. We also propose a frequency-band-wise modeling method based on sub-band multi-rate signal processing (sub-band modeling method) for full-band VC. It enhances the computational efficiency by reducing sampling points of signals converted with filtering and improves converted-speech quality by modeling only the low-frequency band. We conducted several objective and subjective evaluations to investigate the effectiveness of the proposed methods through implementation of the real-time, online, full-band VC system we developed, which is based on the proposed methods. The results indicate that 1) the proposed lifter-training method for narrow-band VC can shorten the tap length to 1/16 without degrading the converted-speech quality, and 2) the proposed sub-band modeling method for full-band VC can improve the converted-speech quality while reducing the computational cost, and 3) our real-time, online, full-band VC system can convert 48 kHz-sampled speech in real time attaining the converted speech with a 3.6 out of 5.0 mean opinion score of naturalness.

Hyperspectral images (HSIs) are generally susceptible to various noise, such as Gaussian and stripe noise. Recently, numerous denoising algorithms have been proposed to recover the HSIs. However, those approaches cannot use spectral information efficiently and suffer from the weakness of stripe noise removal. Here, we propose a tensor decomposition method with two different constraints to remove the mixed noise from HSIs. For a HSI cube, we first employ the tensor singular value decomposition (t-SVD) to effectively preserve the low-rank information of HSIs. Considering the continuity property of HSIs spectra, we design a simple smoothness constraint by using Tikhonov regularization for tensor decomposition to enhance the denoising performance. Moreover, we also design a new unidirectional total variation (TV) constraint to filter the stripe noise from HSIs. This strategy will achieve better performance for preserving images details than original TV models. The developed method is evaluated on both synthetic and real noisy HSIs, and shows the favorable results.

Various graph algorithms have been developed with multiple random walks, the movement of several independent random walkers on a graph. Designing an efficient graph algorithm based on multiple random walks requires investigating multiple random walks theoretically to attain a deep understanding of their characteristics. The first meeting time is one of the important metrics for multiple random walks. The first meeting time on a graph is defined by the time it takes for multiple random walkers to meet at the same node in a graph. This time is closely related to the rendezvous problem, a fundamental problem in computer science. The first meeting time of multiple random walks has been analyzed previously, but many of these analyses focused on regular graphs. In this paper, we analyze the first meeting time of multiple random walks in arbitrary graphs and clarify the effects of graph structures on expected values. First, we derive the spectral formula of the expected first meeting time on the basis of spectral graph theory. Then, we examine the principal component of the expected first meeting time using the derived spectral formula. The clarified principal component reveals that (a) the expected first meeting time is almost dominated by $n/(1+d_{ m std}^2/d_{ mavg}^2)$ and (b) the expected first meeting time is independent of the starting nodes of random walkers, where n is the number of nodes of the graph. davg and dstd are the average and the standard deviation of weighted node degrees, respectively. Characteristic (a) is useful for understanding the effect of the graph structure on the first meeting time. According to the revealed effect of graph structures, the variance of the coefficient dstd/davg (degree heterogeneity) for weighted degrees facilitates the meeting of random walkers.

This letter proposes a downlink multiple-input multiple-output (MIMO) non-orthogonal multiple access technique that mitigates multi-cell interference (MCI) at cell-edge users, regardless of the number of interfering cells, thereby improving the spectral efficiency. This technique employs specific receive beamforming vectors at the cell-edge users in clusters to minimize the MCI. Based on the receive beamforming vectors adopted by the cell-edge users, the transmit beamforming vectors for a base station (BS) and the receive beamforming vectors for cell-center users are designed to eliminate the inter-cluster interference and maximize the spectral efficiency. As each user can directly obtain its own receive beamforming vector, this technique does not require channel feedback from the users to a BS to design the receive beamforming vectors, thereby reducing the system overhead. We also derive the upper bound of the average sum rate achievable using the proposed technique. Finally, we demonstrate through simulations that the proposed technique achieves a better sum rate performance than the existing schemes and that the derived upper bound is valid.

Spectral graph theory provides an algebraic approach to investigate the characteristics of weighted networks using the eigenvalues and eigenvectors of a matrix (e.g., normalized Laplacian matrix) that represents the structure of the network. However, it is difficult to accurately represent the structures of large-scale and complex networks (e.g., social network) as a matrix. This difficulty can be avoided if there is a universality, such that the eigenvalues are independent of the detailed structure in large-scale and complex network. In this paper, we clarify Wigner's Semicircle Law for weighted networks as such a universality. The law indicates that the eigenvalues of the normalized Laplacian matrix of weighted networks can be calculated from a few network statistics (the average degree, average link weight, and square average link weight) when the weighted networks satisfy a sufficient condition of the node degrees and the link weights.

We propose a speech analysis-synthesis and deep neural network (DNN)-based text-to-speech (TTS) synthesis framework using Gaussian mixture model (GMM)-based approximation of full-band spectral envelopes. GMMs have excellent properties as acoustic features in statistic parametric speech synthesis. Each Gaussian function of a GMM fits the local resonance of the spectrum. The GMM retains the fine spectral envelope and achieve high controllability of the structure. However, since conventional speech analysis methods (i.e., GMM parameter estimation) have been formulated for a narrow-band speech, they degrade the quality of synthetic speech. Moreover, a DNN-based TTS synthesis method using GMM-based approximation has not been formulated in spite of its excellent expressive ability. Therefore, we employ peak-picking-based initialization for full-band speech analysis to provide better initialization for iterative estimation of the GMM parameters. We introduce not only prediction error of GMM parameters but also reconstruction error of the spectral envelopes as objective criteria for training DNN. Furthermore, we propose a method for multi-task learning based on minimizing these errors simultaneously. We also propose a post-filter based on variance scaling of the GMM for our framework to enhance synthetic speech. Experimental results from evaluating our framework indicated that 1) the initialization method of our framework outperformed the conventional one in the quality of analysis-synthesized speech; 2) introducing the reconstruction error in DNN training significantly improved the synthetic speech; 3) our variance-scaling-based post-filter further improved the synthetic speech.

A high degree of freedom in spectral domain allows us to accommodate additional optical signal processing for wavelength division multiplexing in photonic analog-to-digital conversion. We experimentally verified a spectral compression to save a necessary bandwidth for soliton self-frequency shift based optical quantization through the cascade of the four-wave mixing based and the sum-frequency generation based spectral compression. This approach can realize 0.03 nm individual bandwidth correspond to save up to more than 85 percent of bandwidth for 7-bit optical quantization in C-band.

Mode-by-mode impulse responses, or spectral transfer matrix (STM) of birefringent fibers are measured by using linear optical sampling, with assist of polarization multiplexed probe pulse. By using the eigenvalue analysis of the STM, the differential mode delay and PMD vector of polarization-maintaining fiber are analyzed as a function of optical frequency over 1THz. We show that the amplitude averaging of the complex impulse responses is effective for enhancing the signal-to-noise ratio of the measurement, resulting in improving the accuracy and expanding the bandwidth of the measurement.

In the age of big data, recommendation systems provide users with fast access to interesting information, resulting to a significant commercial value. However, the extreme sparseness of user assessment data is one of the key factors that lead to the poor performance of recommendation algorithms. To address this problem, we propose a spectral clustering recommendation scheme with low-rank matrix completion and spectral clustering. Our scheme exploits spectral clustering to achieve the division of a similar user group. Meanwhile, the low-rank matrix completion is used to effectively predict un-rated items in the sub-matrix of the spectral clustering. With the real dataset experiment, the results show that our proposed scheme can effectively improve the prediction accuracy of un-rated items.