Recently, non-orthogonal multiple access (NOMA) has gained a great deal of attention due to its ability to simultaneously transmit multiple streams. Device-to-device (D2D) relaying can increase the spectral efficiency via direct communication between two devices, and extends coverage by relaying signals from the base station. In this letter, we propose applying the NOMA technique for D2D relay where D2D relaying and D2D communication can be done simultaneously in the power domain. The proposed scheme can achieve higher spectral efficiency, and its performance is evaluated through extensive simulations in multiple-cell environments, compared with conventional D2D relay schemes.

Wireless technologies that offer high data rate are generally energy-consuming ones while low-energy technologies commonly provide low data rate. Both kinds of technologies have been integrated in a single mobile device for different services. Therefore, if the service does not always require high data rate, the low energy technology, i.e., Bluetooth, can be used instead of the energy-consuming one, i.e., Wi-Fi, for saving energy. It is obvious that energy savings are maximized by turning the unused technology off. However, when active sessions of ongoing services migrate between different technologies, the network-layer connectivity must be maintained, or a vertical handover (VHO) between different networks is required. Moreover, when the networks are not interconnected, the VHO must be fully controlled by the device itself. The device typically navigates traffic through the firmware of the wireless network interface cards (WNIC) using their drivers, which are dependent on the vendors. To control the traffic navigation between WNICs without any modification of the WNICs' drivers, Software-Defined Networking (SDN) can be applied locally on the mobile device, the so called local SDN. In the local SDN architecture, a local SDN controller (SDNC) is used to control a virtual OpenFlow switch, which turns WNICs into its switch ports. Although the SDNC can navigate the traffic, it lacks the global view of the network topology. Hence, to correctly navigate traffic in a VHO process, an extended SDN controller (extSDNC) was proposed in a previous work. With the extSDNC, the SDNC can perform VHO based on a link layer trigger but with a significant packet loss rate. Therefore, in this paper, a framework named esVHO is proposed that executes VHO at the network layer to reduce the packet loss rate and reduce energy consumption. Experiments on VHO performance prove that esVHO can reduce the packet loss rate considerably. Moreover, the results of an energy saving experiment show that esVHO performs high energy saving up to 4.89 times compared to the others.

This paper presents a novel 60 GHz-band photonic-integrated array-antenna and module for radio-over-fiber (RoF)-based beam forming. An integrated photonic array-antennas (IPA), where eight photodiodes and 4×2 arrayed patch-antenna are integrated in a single board, is actually fabricated, and 3.5-Gbit/s QPSK digital signal transmission with beam forming of the IPA is experimentally demonstrated. In addition, a novel 60-GHz compact antenna module is proposed and fabricated for increasing the number of antenna elements and flexibility creating various beam patterns. The feasibility of beam forming operation for the proposed antenna module is confirmed by a 60-GHz RoF transmission experiment. The capability of detecting the mobile terminal direction, which is one of the indispensable functions for actual environment, is also studied. The obtained results in this paper will be useful for designing future radio access networks based on RoF transmission technology.

We present dynamic mode switching characteristic by using a 2 × 2 optical mode switch based on silicon waveguide. The configuration of optical mode switch is similar to MZI where the width of input and output ports are designed to permit the combining of the fundamental mode and the first order mode. We designed the symmetrical arms with phase shifter based on p-i-n structure in one arm to generate a π-phase difference between each arm. As a result, mode switching with the injection current of 60mA (5.7V) was successfully achieved with the mode crosstalk of -10dB at λ=1550nm. A minimum of less than 60ns and 40ns mode switching time for the fundamental mode to first order mode and first order mode to fundamental mode, was achieved respectively in this time.

The Life Intelligence and Office Information System (LOIS) Technical Committee of the Institute of Electronics, Information and Communication Engineers (IEICE) dates its origin to May 1986. This Technical Committee (TC) has covered the research fields of the office related systems for more than 30 years. Over this time, this TC, under its multiple name changes, has served as a forum for research and provided many opportunities for not only office users but also ordinary users of systems and services to present ideas and discussions. Therefore, these advanced technologies have been diffused from big enterprises to small companies and home users responsible for their management and operation. This paper sums up the technology trends and views of the office related systems and services covered in the 30 years of presentations of the LOIS Technical Committees by using the new literature analysis system based on the IEICE Knowledge Discovery system (I-Scover system).

With the expected increase in popularity of device-to-device (D2D) services, the importance of implementing an LTE simulator that enables fast and accurate evaluations of D2D related technologies is clear. In this paper, we report on a network simulator, D2dSim, with the aim of realizing an LTE-Advanced network that utilizes the D2D feature, i.e., in which direct transmission between mobile stations (MSs) is enabled. Using NS-3, one of the most popular network simulation platforms, D2dSim could become one of the first realistic open-source D2D-capable environments, providing realistic and standard-compliant implementations of a subset of Proximity-based Services complying with the LTE-A standard.

An ultra-compact InGaAs photodetector (PD) is demonstrated based on a photonic crystal (PhC) waveguide to meet the demand for a photoreceiver for future dense photonic integration. Although the PhC-PD has a length of only 1.7µm and a capacitance of less than 1fF, a high responsivity of 1A/W was observed both theoretically and experimentally. This low capacitance PD allows us to expect a resistor-loaded receiver to be realized that requires no electrical amplifiers. We fabricated a resistor-loaded PhC-PD for light-to-voltage conversion, and demonstrated a kV/W efficiency with a GHz bandwidth without using amplifiers. This will lead to a photoreceiver with an ultralow energy consumption of less than 1fJ/bit, which is a step along the road to achieving a dense photonic network and processor on a chip.

The analysis and design of a full 360 degrees hybrid coupler phase shifter with integrated distributed elements low pass filters is presented. Pi-section filter is incorporated into hybrid coupler phase shifter for harmonic suppression. The physical size of the proposed structure is close to that of the conventional hybrid coupler phase shifter. The maximum phase shift range is bounded by the port impedance ratio of the hybrid coupler phase shifter. Furthermore, the phase shift range is reduced if series inductance in the reflective load deviates from the optimum value. Numerical and parametric analyses are used to find the equivalent circuit of the pi-section filter for consistent relative phase shift. To validate our analysis, the proposed phase shifter operates at 8.6GHz was fabricated and measured. Over the frequency range of interest, the fabricated phase shifter suppresses second harmonic and achieves analog phase shift of 0 to 360 degrees at the passband, agreeing with the theoretical and simulation results.

To suppress intercell interference for three-cell half-duplex relay systems, joint interference suppression and multiuser detection (MUD) schemes that estimate weight coefficients by the recursive least-squares (RLS) algorithm have been proposed but show much worse bit error rate (BER) performance than maximum likelihood detection (MLD). To improve the BER performance, this paper proposes a joint interference suppression and MUD scheme that estimates the weight coefficients by eigenvalue decomposition. The proposed scheme carries the same advantages as the conventional RLS based schemes; it does not need channel state information (CSI) feedback while incurring much less amount of computational complexity than MLD. In addition, it needs to know only two out of three preambles used in the system. Computer simulations of orthogonal frequency-division multiplexing (OFDM) transmission under three-cell and frequency selective fading conditions are conducted. It is shown that the eigendecomposition-based scheme overwhelmingly outperforms the conventional RLS-based scheme although requiring higher computational complexity.

This paper introduces distributed array antenna (DAA) systems that offer high antenna gain. A DAA consists of several small antennas with improved antenna gain. This paper proposes a technique that suppresses the off-axis undesired radiation and compensates the time delay by combining signal processing with optimization of array element positioning. It suppresses the undesired radiation by compensating the delay timing with high accuracy and deliberately generating the inter-symbol interference (ISI) in side-lobe directions. Computer simulations show its effective suppression of the equivalent isotropic radiated power (EIRP) pattern and its excellent BER performance.

People's body movements in daily face-to-face communication influence each other. For instance, during a heated debate, the participants use more gestures and other body movements, while in a calm discussion they use fewer gestures. This “coevolution” of interpersonal body movements occurs on multiple time scales, like minutes or hours. However, the multi-time-scale coevolution in daily communication is not clear yet. In this paper, we explore the minute-to-minute coevolution of interpersonal body movements in daily communication and investigate the characteristics of this coevolution. We present quantitative data on upper-body movements from thousand test subjects from seven organizations gathered over several months via wearable sensors. The device we employed measured upper-body movements with an accelerometer and the duration of face-to-face communication with an infrared ray sensor on a minute-by-minute basis. We defined a coevolution measure between two people as the number of per-minute changes of their body movement and compared the indices for face-to-face and non-face-to-face situations. We found that on average, the amount of people's body movements changed correspondingly for face-to-face communication and that the average rate of coevolution in the case of face-to-face communication was 3-4% higher than in the case of non-face-to-face situation. These results reveal minute-to-minute coevolution of upper-body movements between people in daily communication. The finding suggests that the coevolution of body movement arises in multiple time scales.

By exploiting the reciprocity and randomness properties of wireless channels, physical-layer-based key generation provides a stable secrecy channel even when the main channel suffers from a bad condition. Even though the channel variation due to the mobility of nodes in wireless channels provides an improvement of key generation rate (KGR), it decreases the key consistency probability (KCP) between the node pairs. Inspired by the received signal strength(RSS)-angle of arrival(AoA)-based geolocation research, in this work, we analyze the performance of the key extraction using the RSS and AoA. We aim to identify a way to utilize the high KGR of the AoA-based method to overcome the major drawback of having a low KGR in the most common RSS-based scheme. Specifically, we derive the KCP and KGR of the RSS-AoA-based key generation scheme. Further, we propose a new performance metric called effective key generation rate (EKGR), to evaluate the designed key generation scheme in practical scenarios. Finally, we provide numerical results to verify the accuracy of the presented theoretical analysis.

In order to support seamless mobility in the Information-Centric Networking (ICN) Architecture we propose the Named-Node Network Architecture (3NA). 3NA introduces two independent namespaces to ICN, the 3N namespace used to uniquely identify nodes within a network and the Point of Attachment (PoA) namespace to identify a node's PoA to the network. The mappings between the two namespaces, along with all the necessary mechanisms to keep the mappings updated over time, are used when routing ICN packets to improve delay and the goodput when either the producer or the consumer are mobile. To support simultaneous producer and consumer mobility, we expand on the 3NA by adding a new Protocol Data Unit (PDU), the DU PDU. The DU PDU permits the encapsulation of ICN packets in a header that has source and destination name fields which belong to 3NA's 3N namespace. The new PDU permits seamless connectivity as long as 3NA's point of attachment signaling is strictly followed. We demonstrate the performance of the DU PDU against our previous defined communication methods and Named Data Networking's (NDN) Smart Flooding forwarding strategy using our open source nnnSIM module for the ns-3 framework. The new PDU outperforms all existing alternatives when the producer or both consumer and provider are mobile, obtaining overall lower mean network delay and higher median goodput.

The application of Intelligent Transport Systems (ITS) transmits data with road-to-vehicle communication (RVC) and inter-vehicle communication (IVC). Digital signature is essential to provide security for RVC and IVC. The public key certificate is used to verify that a public key belongs to an individual prover such as user or terminal. A certificate revocation list (CRL) is used for verifying validity of the public key certificate. A certificate authority (CA) publishes a CRL and distributes it to vehicles. CRL distribution traffic disturbs ITS application traffic because of sharing wireless channel between them. To distribute it on low bit rate will help to ease the disturbance. Although multiplex transmitting is effective in reliable communication, a duplication of received packets is waste of bandwidth as a consequence. This paper proposes a CRL distribution scheme based on random network coding which can reduce duplicate packets. The simulation results show that the number of duplicate packets of the proposed scheme is less than that of a simple error correction (EC)-based scheme and the proposed one can distribute CRL to more vehicles than EC-based ones.

Systematic research on electromagnetic compatibility (EMC) in Japan started in 1977 by the establishment of a technical committee on “environmental electromagnetic engineering” named EMCJ, which was founded both in the Institute of Electronics and Communication Engineers or the present IEICE (Institute of Electronics, Information and Communication Engineers) and in the Institute of Electrical Engineers of Japan or the IEEJ. The research activities have been continued as the basic field of interdisciplinary study to harmonize even in the electromagnetic (EM) environment where radio waves provide intolerable EM disturbances to electronic equipment and to that environment itself. The subjects and their outcomes which the EMCJ has dealt with during about 40 years from the EMCJ establishment include the evaluation of EM environment, EMC of electric and electronic equipment, and EMC of biological effects involving bioelectromagnetics and so on. In this paper, the establishment history and structure of the EMCJ are reviewed along with the change in activities, and topics of the technical reports presented at EMCJ meetings from 2006 to 2016 are surveyed. In addition, internationalization and its related campaign are presented in conjunction with the EMCJ research activities, and the status quo of the EMCJ under the IEICE is also discussed along with the prospects.

As a result of large-scale and complicated of ICT (Information and Communication Technology), the technologies of operations and management of ICT infrastructure and systems are changing to adopt the variation and diversity of usage and communication characteristics. In retrospect, operations and management technologies cover widely from the support of telecommunications operations and remote monitoring for maintaining network equipments, to an integrated network management framework for configuration, monitoring, testing and controls. Recently, the spread of network virtualization technologies enable agility, integrity, and resilience to ICT services. Operations and management technologies will be more important in future, for the support of integrated management of ICT infrastructure including computing resource, and automation of service operations. In this paper, we review research activities of the Technical Committee on Information and Communications Management (ICM) with discussions of individual research category. We then describe the state-of-the-art topics and future directions in the area of ICM.

A study on quantification of human stress using low beta waves of electroencephalography (EEG) is presented. For the very first time the importance of low beta waves as a feature for quantification of human stress is highlighted. In this study, there were twenty-eight participants who filled the Perceived Stress Scale (PSS) questionnaire and recorded their EEG in closed eye condition by using a commercially available single channel EEG headset placed at frontal site. On the regression analysis of beta waves extracted from recorded EEG, it has been observed that low beta waves can predict PSS scores with a confidence level of 94%. Consequently, when low beta wave is used as a feature with the Naive Bayes algorithm for classification of stress level, it not only reduces the computational cost by 7 folds but also improves the accuracy to 71.4%.

The United Nations (UN) reports that the global population reached 7 billion in 2011, and today, it stands at about 7.3 billion. This dramatic increase has been driven largely by the extension of people's lifetime. The urban population has been also increasing, which causes a lot of issues for cities, such as congestion and increased demand for resources, including energy, water, sanitation, education, and healthcare services. A smart city has been expected a lot to solve those issues. The concept of a smart city is not new. Due to the progress of information and communication technology (ICT), including the Internet of Things (IoT) and big data (BD), the concept of a smart city has been being realized in various aspects. This paper introduces the concept and definition of a smart city. Then it explains the ambient intelligence that supports a smart city. Moreover, it introduces several key components of a smart city.

A novel dimensionality reduction method, Fisher Discriminant Locality Preserving Canonical Correlation Analysis (FDLP-CCA), for visualizing Web images is presented in this paper. FDLP-CCA can integrate two modalities and discriminate target items in terms of their semantics by considering unique characteristics of the two modalities. In this paper, we focus on Web images with text uploaded on Social Networking Services for these two modalities. Specifically, text features have high discriminate power in terms of semantics. On the other hand, visual features of images give their perceptual relationships. In order to consider both of the above unique characteristics of these two modalities, FDLP-CCA estimates the correlation between the text and visual features with consideration of the cluster structure based on the text features and the local structures based on the visual features. Thus, FDLP-CCA can integrate the different modalities and provide separated manifolds to organize enhanced compactness within each natural cluster.

Communications satellites have been the primary mission from the early period of Japanese space development and their on-board communication equipment are the core devices to realize satellite communications systems. The technologies for this equipment have been developed to meet the requirements of high capacity and high functionality under the severe satellite-imposed constraints. This paper summarizes progress in on-board communication equipment technologies developed and verified by using Engineering Test Satellites and commercial satellites in Japan and describes their prospects.