Similarities and differences of the thermal analysis issues between the intelligent and general AC contactors are analyzed. Heat source model of the magnet system is established according to the unique control mode of the intelligent AC contactor. Linking with the features common of the two kinds of contactors, the extension of the thermal analysis method of the general AC contactor to the intelligent AC contactor is demonstrated. Consequently, a comprehensive thermal analysis model considering heat sources of both main circuit and magnet system is constructed for the intelligent AC contactor. With this model, the steady-state temperature rise of the intelligent AC contactor is calculated and compared with the measurements of an actual intelligent AC contactor.

Adjustability is an important function of the magnetic release for modern molded case circuit breakers. Based on virtual prototype technology, an automatic prediction method is proposed to design reasonable reactive spring parameters for this kind of magnetic release. 3-D finite element method is adopted to calculate the static characteristics of the magnetic release. Then the dynamic characteristics of the magnetic release can be simulated taking into account the variation of the spring parameters with multi-dynamics method. The calculation results have been verified by the relevant experiments. It demonstrates that the proposed method is feasible to perform the design task.

In this paper a new electromagnetic (EM) interference analysis is proposed using the total harmonic distortion (THD) measurement of the audio signal by the 900 MHz cordless telephones. The cordless telephone network in 900 MHz was built up to be weak in EM interference. 400 and 800 Hz of the sine-wave signal were used in transmitter (TX) system, and the receiver (RX) system was exposed to the EM interference. The THD value varies as the level of the exposed EM interference changes. The model of the cordless telephone also affects the THD value. By using fluctuation of the THD value depending on the amount of the exposure, the threshold value of the interference electric field strength was derived. Based on the derived threshold value of the electric field strength, validity of the regulation value for low power radio devices by CISPR 22 [CLASS B] and FCC is discussed.

The phenomena of retrograde motion of arc in the atmosphere under transverse magnetic field were studied. AgSnO2 contacts were set in DC resistive and inductive circuits, respectively. The break voltage was 28 V, the current ranged from 1 to 5 A, and the magnetic flux density changed from 0 to 100 mT. A high speed camera and an oscilloscope were used to record time variations of arc images, voltages and currents, simultaneously. Different from previous experiment results, the arc motion showed three stages which was more obvious under larger magnetic flux density in inductive circuit. It was also found that the arc movement was closely related with the arc voltage. Explanation to the retrograde motion under such conditions was given.

Method for eliminating magnetic saturation in low-voltage and high-current DC-DC converter with fast dynamic response is described. The magnetic saturation is observed in onboard isolated bridge-type DC-DC converter due to inherently asymmetrical PWM signal during transient condition. The saturation is not eliminated by using ac-coupling capacitor for transformer. Mechanism of the saturation is analyzed and confirmed by experiments. Based on the analysis a solution for the magnetic saturation is proposed. The effectiveness of proposed method is also confirmed by experiments.

This paper describes a black-box model of mixed analog-digital VLSI circuits for the prediction of microcontroller electromagnetic emissions without disclosure of manufacturer data. The model is based on small-signal simulations performed at the analog and digital building-block level, considering also layout and technology parameters, and modeling the parasitic substrate coupling paths and the interconnects. The developed model allows system designers to predict the impact of microcontroller operation on the system-level EMEs by carrying out low-time consuming simulations in the early design phases of their products thus minimizing unnecessary costs and scheduling delays. In this paper, the black-box model of an 8-bit microcontroller is described and it is employed to predict the conducted emission delivered through the input-output ports.

This paper demonstrates an efficient modelling method for artificial materials using digital filtering (DF) techniques. To demonstrate the efficiency of the DF technique it is applied to an electromagnetic bandgap (EBG) structure and a capacitively-loaded loop the so-called, CLL-based metamaterial. Firstly, this paper describes fine mesh simulations, in which a very small cell size (0.10.10.1 mm3) is used to model the details of an element of the structures to calculate the scattering parameters. Secondly, the scattering parameters are approximated with Padé forms and then factorised. Finally the factorised Padé forms are converted from the frequency domain to the time domain. As a result, the initial features in the fine meshes are effectively embedded into a numerical simulation with the DF boundary, in which the use of a coarse mesh is feasible (1,000 times larger in the EBG structure simulation and 680 times larger in the metamaterial simulation in terms of the volumes). By employing the coarse mesh and removal of the dielectric material calculations, the heavy computational burden required for the fine mesh simulations is mitigated and a fast, efficient and accurate modelling method for the artificial materials is achieved. In the case of the EBG structure the calculation time is reduced from 3 hours to less than 1 minute. In addition, this paper describes an antenna simulation as a specific application example of the DF techniques in electromagnetic compatibility field. In this simulation, an electric field radiated from a dipole antenna is enhanced by the DF boundary which models an artificial magnetic conductor derived from the CLL-based metamaterial. As is shown in the antenna simulation, the DF techniques model efficiently and accurately large-scale configurations.

The data dispersion of the measurement of electromagnetic disturbance above 1 GHz is mainly affected by site imperfections (expressed by the site voltage standing wave ratio (SVSWR)). To confirm the relationship between site imperfections and the measured field strength, we measured the SVSWR and the field strength radiated from the equipment under test (EUT) by changing the area covered by the RF absorber on the metal ground plane. From the results, we found that the data dispersion of measured field strength can be estimated from the measured SVSWR, and therefore, we can determine the measurement uncertainty of the measured field strength at the test site.

In this study, a new scanning method for measuring field distributions is proposed. In this method, measurement positions are automatically decided by a magnetic tracker. This method obtains field distributions in real-time, and can display field distribution map successively by interpolating.

In this paper, the transmission and reflection properties of the microstrip line with bends are investigated using the Fourier transform and a mode-matching technique. Based on the waveguide model, the microstrip bends are modeled as the rectangular waveguides with perfect electric conducting top and bottom walls and perfect magnetic conducting side walls. Analytical closed-form expressions for transmission and reflection coefficients are developed using the residue calculus. To verify the proposed method, numerical computations are performed for comparison with 3D full-wave simulations and measurements. A quarter-wavelength transmission line scheme is also proposed to improve the signal integrity of double bend discontinuity.

This paper shows experimental results of packet error rates (PERs) in wireless-LAN mounted printed circuit boards and gives a discussion on a mechanism of electromagnetic noise coupling that affects the PER. We utilized the amplitude probability distribution to investigate the noise coupling channel. We measured the magnetic near-field distribution to obtain information about noise sources. Based on measurement results, we also performed parallel plate resonance analysis to find out electromagnetic interference antennas. We confirmed that noise radiates from a power supply system of a digital circuit and its coupling to a receiving antenna causes an increase of the PER.

A novel approach is proposed for miniaturizing the unit cell size of electromagnetic bandgap (EBG) structures that suppress power plane noise. In this approach, open stubs are introduced into the shunt circuits of these EBG structures. Since the stub length determines the resonant frequencies of the shunt circuit, the proposed structures can maintain the bandgaps at lower frequencies without increasing the unit cell size. The bandgap frequencies were estimated by dispersion analysis based on the Bloch theorem and full-wave simulations. Sample boards of the proposed EBG structures were fabricated with a unit cell size of 2.1 mm. Highly suppressed noise propagation over the estimated frequency range of 1.9-3.6 GHz including the 2.4-GHz wireless-LAN band was experimentally demonstrated.

At some point in a digital communications receiver, the received analog signal must be sampled. Good performance requires that these samples be taken at the right times. The process of synchronizing the sampler with the received analog waveform is known as timing recovery. Conventional timing recovery techniques perform well only when operating at high signal-to-noise ratio (SNR). Nonetheless, iterative error-control codes allow reliable communication at very low SNR, where conventional techniques fail. This paper provides a detailed review on the timing recovery strategies based on per-survivor processing (PSP) that are capable of working at low SNR. We also investigate their performance in magnetic recording systems because magnetic recording is a primary method of storage for a variety of applications, including desktop, mobile, and server systems. Results indicate that the timing recovery strategies based on PSP perform better than the conventional ones and are thus worth being employed in magnetic recording systems.

Correction factors are presented for estimating the RF electromagnetic field strength in the compliance assessment of human exposure from an indoor RF radio source in the frequency range from 800 MHz to 3.5 GHz. The correction factors are derived from the increase in the spatial average electric field strength distribution, which is dependent on the building materials. The spatial average electric field strength is calculated using relative complex dielectric constants of building materials. The relative complex dielectric constant is obtained through measurement of the transmission and reflection losses for eleven kinds of building materials used in business office buildings and single family dwellings.

In this paper, we have succeeded in the fabrication of high performance Magnetic Tunnel Junction (MTJ) which is integrated in CMOS circuit with 4-Metal/ 1-poly Gate 0.14 µm CMOS process. We have measured the DC characteristics of the MTJ that is fabricated on via metal of 3rd layer metal line. This MTJ of 60180 nm2 achieves a large change in resistance of 3.52 kΩ (anti-parallel) with TMR ratio of 151% at room temperature, which is large enough for sensing scheme of standard CMOS logic. Furthermore, the write current is 320 µA that can be driven by a standard MOS transistor. As the results, it is shown that the DC performance of our fabricated MTJ integrated in CMOS circuits is very good for our novel spin logic (MTJ-based logic) device.

In this paper, it is shown that our fabricated MTJ of 60180 nm2, which is connected to the MOSFET in series by 3 levels via and 3 levels metal line, can dynamically operate with the programming current driven by 0.14 µm CMOSFET. In our measurement of transient characteristic of fabricated MTJ, the pulse current, which is generated by the MOSFET with an applied pulse voltage of 1.5 V to its gate, injected to the fabricated MTJ connected to the MOSFET in series. By using the current measurement technique flowing in MTJ with sampling period of 10 nsec, for the first time, we succeeded in monitor that the transition speed of the resistance change of 60180 nm2 MTJ is less than 30 ns with its programming current of 500 µA and the resistance change of 1.2 kΩ.

A new technique to estimate the Poynting vector distribution from near-magnetic-field measurement is proposed. To calculate the Poynting vector, both electric and magnetic field should be known. In the proposed method, only magnetic-field measurement of three orthogonal axes is required. Electric field is estimated from the measured magnetic field by using the Maxwell's equation. The modified Yee cell is employed to estimate electric field from the measured magnetic field. Finally, the Poynting vector is calculated from the measured magnetic field and the estimated electric field. Since the proposed method enables us to understand propagation direction of electro-magnetic energy, it can be utilized to locate an emission source and to investigate a mechanism of undesired emission. Experiments are carried out to discuss the accuracy and to validate practical usefulness.

Radar cross sections of polygonal cylinders are investigated by using a kind of mode matching methods. Applying two types of novel field-decomposition techniques, electromagnetic scattering analysis can be performed very precisely. We will discuss computational accuracy of our proposed method and the proper choice of field-decomposition techniques for a rectangular cylinder with various shapes of wedge cavities and bumps.

We propose a novel short-range wireless communications technology that uses quasi-static electric fields; it enables data communication between devices separated by up to 10 cm via dielectric media at a speed of 10 Mbps. It is considered to be a secure wireless technology since communication area is restricted to below about 10 cm. To suppress electromagnetic radiation, we adopted a baseband transmission scheme in which the quasi-static electric field is directly modulated by 10 BASE-T data signals. Since the spectra of the data signals are concentrated to below 20 MHz, the amplitude of the electric field rapidly decreases outside the communication area. This contributes to enhancing security of the communications system. In this paper, we explain a basic principle of the short-range wireless communications technology. Since baseband data signals are carried by the quasi-static electric field, the quality of the communication is easily degraded by the existence of the earth ground. To isolate the communications system from the earth ground, we introduce a novel electro-optic sensor to receive the quasi-static electric field. With the electro-optic sensor, stable data communication is possible at 10 Mbps via dielectric materials, such as a wooden table.

We investigated an analogue modulation of magneto-optic spatial light modulator (MOSLM). For enhancement of the modulation from the voltage-driving MOSLM, magnetostriction and saturation magnetization of magnetic garnet films and piezoelectric constant of PZT films were investigated. The performance was expected to be improved by using Bismuth, Dysprosium and Aluminum substituted Yttrium Iron garnet, which effective magnetic field showed 20 times higher than Yttrium Iron garnet.