This paper proposes low-power voltage-mode/current-mode hybrid circuits to realize an arbitrary two-variable logic function and a full-adder function. The voltage and current mode can be selected for low-power operations at low and high frequency, respectively, according to speed requirement. An nMOS pass transistor network is shared to realize voltage switching and current steering for the voltage- and current-mode operations, respectively, which leads to high utilization of the hardware resources. As a result, when the operating frequency is more than 1.15,GHz, the current mode of the hybrid logic circuit is more power-efficient than the voltage mode. Otherwise, the voltage mode is more power-efficient. The power consumption of the hybrid two-variable logic circuit is lower than that of the conventional two-input look-up table (LUT) using CMOS transmission gates, when the operating frequency is more than 800,MHz. The delay and area of the hybrid two-variable logic circuit are increased by only 7% and 13%, respectively

A global tree local X-net network (GTLX) is introduced to realize high-performance data transfer in a multiple-valued fine-grain reconfigurable VLSI (MVFG-RVLSI). A global pipelined tree network is utilized to realize high-performance long-distance bit-parallel data transfer. Moreover, a logic-in-memory architecture is employed for solving data transfer bottleneck between a block data memory and a cell. A local X-net network is utilized to realize simple interconnections and compact switch blocks for eight-near neighborhood data transfer. Moreover, multiple-valued signaling is utilized to improve the utilization of the X-net network, where two binary data can be transferred from two adjacent cells to one common adjacent cell simultaneously at each “X” intersection. To evaluate the MVFG-RVLSI, a fast Fourier transform (FFT) operation is mapped onto a previous MVFG-RVLSI using only the X-net network and the MVFG-RVLSI using the GTLX. As a result, the computation time, the power consumption and the transistor count of the MVFG-RVLSI using the GTLX are reduced by 25%, 36% and 56%, respectively, in comparison with those of the MVFG-RVLSI using only the X-net network.

This paper presents a fine-grain bit-serial reconfigurable VLSI architecture using multiple-valued switch blocks and binary logic modules. Multiple-valued signaling is utilized to implement a compact switch block. A binary-controlled current-steering technique is introduced, utilizing a programmable three-level differential-pair circuit to implement a high-performance low-power arbitrary two-variable binary function, and increase the noise margins in comparison with the quaternary-controlled differential-pair circuit. A current-source sharing technique between a series-gating differential-pair circuit and a current-mode D-latch is proposed to reduce the current source count and improve the speed. It is demonstrated that the power consumption and the delay of the proposed multiple-valued cell based on the binary-controlled current-steering technique and the current-source-sharing technique are reduced to 63% and 72%, respectively, in comparison with those of a previous multiple-valued cell.

A multiple-valued data transfer scheme using X-net is proposed to realize a compact bit-serial reconfigurable VLSI (BS-RVLSI). In the multiple-valued data transfer scheme using X-net, two binary data can be transferred from two adjacent cells to one common adjacent cell simultaneously at each “X” intersection. One cell composed of a logic block and a switch block is connected to four adjacent cross points by four one-bit switches so that the complexity of the switch block is reduced to 50% in comparison with the cell of a BS-RVLSI using an eight nearest-neighbor mesh network (8-NNM). In the logic block, threshold logic circuits are used to perform threshold operations, and then their binary dual-rail voltage outputs enter a binary logic module which can be programmed to realize an arbitrary two-variable binary function or a bit-serial adder. As a result, the configuration memory count and transistor count of the proposed multiple-valued cell are reduced to 34% and 58%, respectively, in comparison with those of an equivalent CMOS cell. Moreover, its power consumption for an arbitrary 2-variable binary function becomes 67% at 800 MHz under the condition of the same delay time.

This paper presents a low-power FPGA based on mixed synchronous/asynchronous design. The proposed FPGA consists of several sections which consist of logic blocks, and each section can be used as either a synchronous circuit or an asynchronous circuit according to its workload. An asynchronous circuit is power-efficient for a low-workload section since it does not require the clock tree which always consumes the power. On the other hand, a synchronous circuit is power-efficient for a high-workload section because of its simple hardware. The major consideration is designing an area-efficient synchronous/asynchronous hybrid logic block. This is because the hardware amount of the asynchronous circuit is about double that of the synchronous circuit, and the typical implementation wastes half of the hardware in synchronous mode. To solve this problem, we propose a hybrid logic block that can be used as either a single asynchronous logic block or two synchronous logic blocks. The proposed FPGA is fabricated using a 65-nm CMOS process. When the workload of a section is below 22%, asynchronous mode is more power-efficient than synchronous mode. Otherwise synchronous mode is more power-efficient.

This paper presents an asynchronous FPGA that combines 4-phase dual-rail encoding and LEDR (Level-Encoded Dual-Rail) encoding. 4-phase dual-rail encoding is employed to achieve small area and low power for function units, while LEDR encoding is employed to achieve high throughput and low power for the data transfer using programmable interconnection resources. Area-efficient protocol converters and their control circuits are also proposed in transistor-level implementation. The proposed FPGA is designed using the e-Shuttle 65nm CMOS process. Compared to the 4-phase-dual-rail-based FPGA, the throughput is increased by 69% with almost the same transistor count. Compared to the LEDR-based FPGA, the transistor count is reduced by 47% with almost the same throughput. In terms of power consumption, the proposed FPGA achieves the lowest power compared to the 4-phase-dual-rail-based and the LEDR-based FPGAs. Compared to the synchronous FPGA, the proposed FPGA has lower power consumption when the workload is below 35%.

A fine-grain bit-serial multiple-valued reconfigurable VLSI based on logic-in-control architecture is proposed for effective use of the hardware resources. In logic-in-control architecture, the control circuits can be merged with the arithmetic/logic circuits, where the control and arithmetic/logic circuits are constructed by using one or multiple logic blocks. To implement the control circuit, only one state in a state transition diagram is allocated to one logic block, which leads to reduction of the complexity of interconnections between logic blocks. The fine-grain logic block is implemented based on multiple-valued current-mode circuit technology. In the fine-grain logic block, an arbitrary 3-variable binary function can be programmed by using one multiplexer and two universal literal circuits. Three-variable binary functions are used to implement the control circuit. Moreover, the hardware resources can be utilized to construct a bit-serial adder, because full-adder sum and carry can be realized by programming in the universal literal circuit. Therefore, the logic block can be effectively reconfigured for arithmetic/logic and control circuits. It is made clear that the hardware complexity of the control circuit in the proposed reconfigurable VLSI can be reduced in comparison with that of the control circuit based on a typically sequential circuit in the conventional FPGA and the fine-grain field-programmable VLSI reported until now.

This paper presents a novel asynchronous architecture of Field-programmable gate arrays (FPGAs) to reduce the power consumption. In the dynamic power consumption of the conventional FPGAs, the power consumed by the switch blocks and clock distribution is dominant since FPGAs have complex switch blocks and the large number of registers for high programmability. To reduce the power consumption of switch blocks and clock distribution, asynchronous bit-serial architecture is proposed. To ensure the correct operation independent of data-path lengths, we use the level-encoded dual-rail encoding and propose its area-efficient implementation. The proposed field-programmable VLSI is implemented in a 90 nm CMOS technology. The delay and the power consumption of the proposed FPVLSI are respectively 61% and 58% of those of 4-phase dual-rail encoding which is the most common encoding in delay insensitive encoding.

A fine-grain reconfigurable VLSI for various applications including arithmetic operations is developed. In the fine-grain architecture, it is important to define a cell function which leads to high utilization of a logic block and reduction of a switch block. From the point of view, a universal-literal-based multiple-valued cell suitable for bit-serial reconfigurable computation is proposed. A series-gating differential-pair circuit is effectively employed for implementing a full-adder circuit of Sum and a universal literal circuit. Therefore, a simple logic block can be constructed using the circuit technology. Moreover, interconnection complexity can be reduced by utilizing multiple-valued signaling, where superposition of serial data bits and a start signal which indicates heading of one-word is introduced. Differential-pair circuits are also effectively employed for current-output replication, which leads to high-speed signaling to adjacent cells The evaluation is done based on 90 nm CMOS design rule, and it is made clear that the area of the proposed cell can be reduced to 78% in comparison with that of the CMOS implementatiuon. Moreover, its area-time product becomes 92% while the delay time is increased by 18%.