We demonstrate a novel display structure for color electronic paper for the first time. Fully transparent amorphous oxide TFT array is directly deposited onto color filter array and combined with E Ink Imaging Film. Taking advantage of the transparent property of the oxide TFT, the color filter and TFT array are positioned at the viewing side of the display. This novel "Front Drive" display structure facilitates the alignment of the color filter and TFT dramatically.

The radiation characteristics of a monopole antenna that consists of one-half of a bow-tie dipole antenna, made of optically transparent conductive thin film and mounted above a ground plane, are investigated. The antenna's performance is measured for several films with different sheet resistivities. It is found that the gain lowering of the antenna caused by material resistance decreases from 4.4 dB to 0.2 dB at 2.4 GHz and the efficiency of the antenna increases from 46% to 93% at the same frequency, as the sheet resistivity decreases from 19.8 Ω/ to 1.3 Ω/. The antenna is analyzed by the moment method. A wire-grid model with resistance loading on every discretized wire is applied. The analyzed results agree with the experimental values very well.

In this paper an analysis of component and system reliability for lattice systems is proposed when component failures are not statistically independent. We deal the case that the failure rate of a component depends on the number of the adjacent failed components. And we discuss the maintainability of the system when a failed component is replaced by a spare component. At first we discuss the approximated reliability of each component. Then we estimate the mean number of failed components. Furthermore, the system reliability is approximated by using the component reliability.

This paper considers the reliable multicast transport protocols used in hybrid networks that include wired and wireless networks and transparent proxy servers. We present four analytic performance models of two extreme reliable multicast transport protocols, sender-initiated and receiver-initiated, and supported and unsupported by transparent proxy servers are considered in each reliable multicast protocol. We analyze the throughputs of these four different models mathematically. Numerical results show that transparent proxy servers give good effects to overall performance. Furthermore, the receiver-initiated reliable multicast supported by transparent proxy servers gives better performances of total throughput than sender-initiated reliable multicast supported by transparent proxy servers. We provide efficiency criterion of the optimal number of transparent proxy servers for each protocol under varying wireless loss probabilities. Numerical results are verified by simulations.

When a large-size car exists on the ETC lane (Electronic Toll Collection System), there is the possibility that the interference on the adjacent lane occurs by the scattering waves from one. In this paper, we propose a new improvement method which the transparent EM wave absorber is placed between the ETC lane and the adjacent one in order to suppress the scattering waves from a large-size car. Therefore, we design the transparent EM wave absorber which consists of the transparent resistive and conductive films. Then, this absorber is produced, and its reflection and transmission coefficients are evaluated. In addition, its transmittance in optics is evaluated. As the results, the reflectivity of this absorber is obtained lower than -20 dB in the oblique incident angle from 0to 30at 5.8 GHz circular polarized wave, abbreviated as CP wave, and also the transmittivity is obtain lower than -27 dB in the oblique incident angle from 0to 70, respectively. On the other hand, the transmittance in optics is obtained higher than 60%. Moreover, we study experimentally on the ETC system with placing this absorber between the ETC lane and the adjacent one. We measured the distribution of receiving power on the adjacent lane, when a water sprinkler existed on the ETC lane. As a result, it is confirmed that the receiving power on the adjacent lane could be realized lower than -70.5 dBm, and then a new improvement method has proven to be very useful in the ETC system.

This paper first discusses the misinterpretation of the concept of "ubiquitous computing" that Mark Weiser originally proposed in 1991. Weiser's main message was not the ubiquity of computers, but the transparency of interface that determines users' perception of digital technologies embedded in our physical environment seamlessly. To explore Weiser's philosophy of transparency in interfaces, this paper presents the design of an interface that uses glass bottles as "containers" and "controls" for digital information. The metaphor is a perfume bottle: Instead of scent, the bottles have been filled with music -- classical, jazz, and techno music. Opening each bottle releases the sound of a specific instrument accompanied by dynamic colored light. Physical manipulation of the bottles -- opening and closing -- is the primary mode of interaction for controlling their musical contents. The bottles illustrates Mark Weiser's vision of the transparent (or invisible) interface that weaves itself into the fabric of everyday life. The bottles also exploits the emotional aspects of glass bottles that are tangible and visual, and evoke the smell of perfume and the taste of exotic beverages. This paper describes the design goals of the bottle interface, the arrangement of musical content, the implementation of the wireless electromagnetic tag technology, and the feedback from users who have played with the system.

In this paper, a fragment-processing solution in 3D graphics rendering algorithms based on fragment lists (i.e. A-buffer) for minimizing loss of image quality is described. While all fragment information should be preserved for exact hidden surface removal, this places additional strain on hardware in terms of silicon gates and clock cycles. Therefore, we propose a fragment processing technique that can effectively merge fragments in order to decrease the depth of fragment lists. It renders scenes quite accurately even in the case when three fragments intersect each other. This algorithm improves hardware acceleration without deteriorating image quality.

A novel in vivo exposure setup has been developed for testing the possible promoting effects of 1.5 GHz digital cellular phones on mouse skin carcinogenesis. The exposure setup has two main features: one is the employment of an electrically short monopole antenna with capacitive-loading, which supplies the ability to realize a highly localized peak SAR above 2 W/kg without any thermal stress for a mouse; the other is the use of a transparent absorber to allow real-time observation of both the exposure process as well as mouse activities during the exposure. Dosimetric analyses for the exposure setup have been carried out both numerically and experimentally. Good agreement was confirmed between the numerical and experimental results, thereby demonstrating the validity of the novel exposure setup.

Migration transparency is considered in the context of multi-agent systems. A mobile agent architecture is proposed with an Availability service and a Transparency interface. We define mobility as explicit (or proactive) when the agent decides when and where to move and define mobility as implicit (i. e. , transparent or reactive) when it is a consequence of changes in the environment. Implicit mobility of agents is explored in addition to the usual explicit mobility. The search for a target agent (or agency) follows a transparent location and selection. The client agent preferably moves towards the target agent. If not possible, the target agent will move towards the client agent when calling back. If both agents can not move then the execution takes place remotely or is abandoned. Transparency is goal oriented.

Human visual system can perceive 3-D structure of an object by binocular disparity, gradient of illumination (shading), occlusion, textures, perspective and so forth. Among them, binocular disparity seems to be the essentially important cues for the 3-D space perception and it is used widely for displaying 3-D visual circumstances such as in VR (virtual reality) system or 3-D TV. Visual illusions seem to be one of the phenomena which are purely reflecting the mechanism of human visual system. In the recent several years, the authors found several new types of 3-D visual illusions with binocular viewing. Entire 3-D illusory object including volume perception, transparency, dynamic illusions can be perceived only from the visual stimuli of disparity given by some inducing objects arranged with suitable relations. In this report, the authors introduced these newly found visual illusions and made some considerations on the human visual mechanism of 3-D perception and on their exploitation for new effective techniques in 3-D display. They introduced especially on the visual effect in two kinds of arrangement with occlusion and sustaining relationship between the illusory object and inducing objects. In the former case, the inducing objects which provide the stimuli were named as occlusion cues and classified into two types: contour occlusion cues and bulky occlusion cues. In the later case, those inducing objects were named as sustaining cues and a 3-D fully transparent illusory object was perceived. The perception was just like imagined from the scenes of the actions and positions of the pantomimists; then this phenomena was named as "Mime (Pantomime) Effect. " According to the positions of sustaining cues, they played different actions in this perception, and they are classified into three types: front sustaining cues, side sustaining cues and back sustaining cues. In addition, dynamic fusion and separation of volumetrical illusory objects were perceived when the visual stimuli were moving continuously between two structurally different conditions. Then the hysteresis was recognized in geometrical position between the fusion and separation. The authors believe that the occlusion cues and sustaining cues introduced in this paper could be effective clues for exploiting the new techniques for 3-D display.

This paper discusses the implementation and cost- and performance- evaluations of a distributed processing network, called DONA-α, which is one of the possible physical networks mainly implementing connection-oriented public switched network functions corresponding to OSI layers 1 to 3. The first feature of the DONA-α network is that it separates a switching subsystem and a control subsystem of a conventional switching system and independently allocates them over distributed nodes as a switching node and a control node. Each DONA-α switching node is given a much smaller switching capacity than the switching subsystem of the conventional switching system and is located near subscribers. In contrast, each DONA-α control node has much higher performance than the control subsystem of the conventional switching system. This allows a large number of switching nodes to share the same control node, which controls their connection setups. This separation provides the network with greater flexibility and allows more effective utilization of network resources, such as control processors, switching fabrics, and transmission links, than ever before. The second feature of DONA-α is that it provides a network with network-wide distribution transparency. This allows network resources including software such as databases and application programs to be shared and therefore to be utilized in the network more easily and more efficiently. The results of a network performance simulation and cost calculation confirm the viability of the DONA-α network.

The self-healing capability against network failure is one of indispensable features for the B-ISDN infrastructure. One problem in realizing such self-healing backbone network is the inefficient utilization of the large spare capacity designed for the failure-restoration purpose since it will be used only in the failure time that does not occur frequently. "Pool-capacity" is the concept that allows some VPs (virtual paths) to efficiently utilize this spare capacity part. Although the total capacity can be saved by using the "Pool Capacity," it is paid by less reliability of VPs caused by the emerging influence of indirect-failure. Thus, this influence of indirect-failure has to be considered in the capacity designing process so that network-designers can trade off the saving of capacity with the reliability level of VPs in their self-healing networks. In this paper, Damage Rate:DR which is the index to indicate the level of the influence caused by indirect-failure is defined and the pool-capacity design scheme with DR consideration is proposed. By the proposed scheme, the self-healing network with different cost (pool-capacity) can be designed according to the reliability level of VPs.

A reconfiguration method for processor array is proposed in this paper. In the method, genetic algorithm (GA) is used for searching effective spare arrangement, which leads to successful reconfiguration. The effectiveness of the method is demonstrated by computer simulations.

We present a realization of the transparent wave absorber effective for the use at V-band frequency. First, we propose a structure of the transparent wave absorber consisting of spacer (polycarbonate) and two transparent resistive sheet (polyethylene terephtalate deposited with Indium Tin Oxide) used as a reflection film and an absorption film. Second, a design chart for this type of wave absorber is shown. Third, a design method and manufacturing process of the transparent wave absorber are described particularly for V-band frequency. As a result, the measurement of reflection loss of the absorber indicate that a peak absorption of 32-38 dB is attained at a target frequency of 60 GHz.

Bursts from a number of variable bit rate sources allocated to a virtual path with a given capacity can inundate the channel. Buffers used to take care of such bursts can fill up rapidly. The buffer size limits its burst handling capability. With large bursts or a number of consecutive bursts, the buffers fill up and this leads to high cell losses. Channel reconfiguration with dynamic allocation of spare capacities is one of the methods used to alleviate such cell losses. In reconfigurable networks, spare capacity allocation can increase the channel rates for short durations, to cope with the excess loads from the bursts. The dynamic capacity allocations are adaptable to the loads and have fast response times. We propose heuristic rules for spare capacity assignments in ATM networks. By monitoring buffer occupancy, triggers which anticipate excess traffic can be used to assign spare capacities to reduce the cell loss probabilities in the network.

To enhance fabrication yield for processor arrays, many reconfiguration schemes for replacing faulty processing elements (PE's) with spare PE's have been proposed. An array grid model based on single-track switches is one of such models. For this model, some algorithms for reconfiguring processor arrays have been proposed. However, any algorithm which can reconfigure the array, whenever the array is reconfigurable, has not been proposed as yet. This paper describes reconfiguration methods of processor arrays with faulty PE's. The methods use indirect replacements for reconfiguring arrays. First, we introduce a concept of fatal fault pattern, which makes an array unreconfigurable. Then, for the reconfiguration method with fixed spare arrangement, efficient spare arrangements are given by evaluating the probability of an occurring fatal fault pattern. Furher, we present reconfiguration algorithm with relocating spare. In the algorithm, fatal fault patterns are eliminated by relocating spare. Computer simulations show that the method has good performance of reconfiguration.

To enhance fabrication yield for processor arrays, many reconfiguration schemes for replacing faulty processing elements (PE's) with spare PE's have been proposed. An array grid model based on single-tracks is one of such models. For this model, some algorithms for reconfiguring processor arrays have been proposed. However, an algorithm which can reconfigure the array, whenever the array is reconfigurable, has not been proposed yet. This paper presents two types of methods for reconfiguration of processor arrays. Both the types use indirect replacements for reconfiguring arrays. For an indirect replacement of a faulty non-spare PE, one has a fixed direction, the other has at most four directions among which one is chosen. For the former, we consider the several distribution of spare PE's, and computer simulations show a tendency in the term of difference in the distributions. The latter algorithms consist of two phases. In the first phase, rows and columns of spare PE's are decided in accordance with a rule. Several rules for deciding spare PE's are considered in this paper. In the second phase, faulty non-spare PE's are replaced with healthy spare PE's. By simulations the performance of the algorithms are evaluated and a tendency is shown in the terms of difference in disposition of spare PE's.

We proposed a new thchnique using saw wave modulation light to measure the thermal diffusivity of a transparent adhesive by photoacoustic microscope. In this technique, the time required for the measurement of it can be reduced by one-fifth compared with that of a conventional method.

A self-induced-transparent (SIT) system that takes advantage of morphology dependent resonances (MDR's) in a Mie-sized microsphere doped with a resonant material is proposed. The present system is doubly resonant: one has microscopic origin (the two-level system), while the other has macroscopic origin (the MDR). In this geometry, owing to the feedback action of MDR's, the pulse area can be much expanded, and thus the electric-field amplitude of the incident pulse can be reduced substantially compared with the conventional one-way SIT propagation. Theoretical results that incorporate dephasing due to structural imperfections are shown.

We developed an eye-contact technique using a blazed half-transparent mirror (BHM), which is a micro-HM array arranged on the display surface, to make a compact eye-contact videophone. This paper describes a new BHM structure that eliminates ghosts and improves image quality. In the new BHM, the reflection and transmission areas are separated to exclude ghosts from appearing in the captured image. We evaluated the characteristics of the captured and displayed images. The results show that the contrast ratio of the captured image and the brightness of both captured and displayed images are much better than with the previous BHM.