We propose a stability-guaranteed width control (SGWC) for the hot strip finishing mill. It is shown that the proposed SGWC guarantees the stability of the width controller by the universal approximation of the neural network. It is shown through the field test in the hot strip mill of POSCO that the stability of the width controller is guaranteed by the proposed control scheme.

A novel low insertion-loss and wideband microstrip bandpass filter has been designed and tested. The basic configuration of this novel dual-mode filter is a square ring resonator with direct-connected orthogonal feed lines, and dual-perturbation elements are introduced within the resonator at symmetrical location. The effects of the size of the perturbation element are studied. A new filter having wider bandwidth and transmission zeros are presented. The proposed filter responses are in good agreement with the simulations and experiments.

A stacked rectangular microstrip antenna with a shorting plate is proposed as a car antenna for dual band (VICS and ETC) operation in the ITS. The proposed antenna has the proper radiation patterns for the VICS and ETC. The antenna is small in size and effective in dual band operation.

This paper describes a beam scanning antenna that consists of a movable dielectric plate loaded onto a microstrip comb-line antenna. This type of antenna uses a mechanical system and so offers a simple structure and low cost. The main beam direction of the proposed antenna is changed by moving the dielectric plate. The guide wavelength of the microstrip line was measured at the quasi-millimeter wave band (20 GHz) when moving the dielectric plate to investigate the possibility of beam scanning. The proposed antenna was fabricated to experimentally demonstrate its principle operation. A possible beam scanning angle of 20 degrees was confirmed.

Novel multiband circular microstrip antennas (C-MSAs) with multiple half-ring slots are presented in this paper. Two antenna-feeding systems, i.e. an embedded L-probe beneath the patch and a coplanar circular arc- shaped probe (T-probe), are used to feed the C-MSA with multiple half-ring slots. The embedded L-probe is used to excite the C-MSA with a double-layer dielectric substrate due to its tremendous performance to provide a wideband impedance matching. The coplanar T-probe is proposed to realize an excellent multiband C-MSA in a single-layer structure. The C-MSA with four half-ring slots fed by the embedded L-probe exhibits satisfactory radiation characteristics. Five frequencies with broadside radiation patterns and gains of at least 5.0 dBi are obtained. It is also confirmed by simulation that resonant frequency and gain can be easily controlled to meet the desired frequency requirements. Moreover, the C-MSA with three half-ring slots fed by the coplanar T-probe presents satisfactory performance over the four observed frequencies with good return losses (-10 dB reference). Broadside radiation patterns with acceptable cross-polarization level and gains in the range of 3.0-7.0 dBi are obtained. Couplings between the C-MSA and the coplanar T-probe have an important contribution to obtain good return losses. It can be controlled by adjusting the distance between them and the arc angle of the coplanar T-probe appropriately. Experiments of both types of antenna were conducted to verify the simulation results and good agreements are confirmed. Due to the performances, these two C-MSAs are considered to be an effective model as a multiband planar antenna.

Transmission characteristics of a left-handed (LH) ferrite microstrip line are significantly affected by the nonuniform DC bias magnetic field in the ferrite substrate (internal magnetic field Hin) caused by the inhomogeneous demagnetizing effect because the strip conductors of these devices must be mounted at the edge of the ferrite substrate. Three dimensional analyses on the LH ferrite microstrip line are performed taking into account the nonuniform internal magnetic field Hin. The analytical results show that the nonuniform internal magnetic field under the strip conductor near the edge of the ferrite substrate is useful for spreading the frequency band of negative permeability and nonreciprocal operation, and for improvement of both the insertion and return losses of the LH ferrite microstrip line. Measured results of more than 20 dB isolation with 2.2 dB insertion loss and 1.33 GHz bandwidth are corresponding well to the analytical results.

For a microstrip antenna (MSA) with a ring-shaped slot on formed on the ground plane, downsizing the microstrip patch and expanding the circularly polarized bandwidth have been achieved successfully. The dimensions of the patch are 6.8 mm7.4 mm and the minimum axial ratio (AR) of 0.6 dB is obtained at 6.1 GHz. In addition, its AR is less than 3 dB at the relative bandwidth of 3.5%. The bandwidth of the proposed MSA is twice that of conventional single-feeding circularly polarized MSAs; however, its size is only half that of conventional MSAs.

Since Smart Antenna technology has powerful spatial processing ability; it is regarded as a promising approach to enhancing the data rates and capacity of wireless LAN systems. In this paper, a small size, practical switched-beam antenna system, well suited for domestic in-home networking in the 2.4 GHz band, is designed and tested. The system has the configuration of regular nine-prism, and nine 1/4 wavelength rectangular patches are symmetrically distributed on the nine sides of the prism. The switching process is based on control of the microstrip used to feed the patch radiators, by placing PIN diodes at the microstrip feeding lines. The antenna array can generate nine beams with a gain of 11 dB. All the beams generated by the system are cophasal excited and have a 40°beamwidth. Compared to the uniform array, the system can guarantee the consistency of every beam and is preferable in shape.

For the uplink of a radio-on-fiber system or an electromagnetic field sensor, a resonant type optical modulator array connected with antennas can effectively convert a micro/millimeter-wave to a light wave. We designed and fabricated 10 GHz band resonant modulators and micro-strip antennas. And we demonstrated the simultaneous operation of four modulators using power received by micro strip antennas connected to each modulator. We confirmed that the optical phase change induced by the received power could be proportionally increased with the number of arrays.

Transitions between a post-wall waveguide and a microstrip line are proposed as the key components for cost-effective millimeter-wave modules. A transition with a coaxial structure is investigated for LTCC laminated layers and 11.3% bandwidth for the reflection smaller than -15 dB is realized in 60 GHz band. The overall connector loss with 1 cm post-wall would be about 0.8 dB. The degradation due to fabrication error is also assessed. The transition in LTCC substrate fulfills electrical and manufacturing demands in millimeter-wave bands.

In this paper, the authors propose a circularly polarized printed antenna combining a slot array antenna and a patch antenna, with dual-band operation. The proposed antenna has good isolation performance, is compact, and has simple configuration. This antenna is composed of two parts, a patch antenna (for Rx) on the top, and a slot array antenna (for Tx) on the bottom, respectively. The element layout is such that the lower radiation element is not hidden by the upper one for wide observation angle. Hence, both radiation elements can naturally radiate the targeted polarization. Both slot array and patch antenna are fed by electromagnetically coupled microstrip line feed. With such a configuration, it is possible to efficiently obtain good isolation characteristics for both frequency bands. Furthermore, this antenna can be easily composed and it is not necessary to use any feeding pin or via hole. The target of this antenna is mobile communications applications such as mobile satellite communications, base-station of wireless LAN, etc. Here, the design techniques are discussed and the numerical and experimental analyses are presented.

This paper presents a low cost and portable DOA (Direction Of Arrival) estimation system for surveillance using a modifed beamspace MUSIC (MUltiple Signal Classification) by a quasi-orthogonal multi-beam. This is instead of DFT processing and hardware system consisting of chip-sized phase shifters, a single ADC (Analogue to Digital Converter) and a single TR (TRanceiver) module for an antenna array. In the beamspace MUSIC, generated beampatterns have orthogonal properties. This proposed system cannot make such a beampattern due to the variable range limitation of phase shifter, then we use the quasi-orthogonal beam obtained by the calculation of correlation coefficient for beampattern. We demonstrate the proposed system using 4-element microstrip array antenna and chip-sized phase shifters. The DOA experiment in anechoic chamber confirms the proposed system performance.

A broadband microstrip-to-waveguide transition is developed in the millimeter-wave band. No additional parts and complicated structures are needed to extend the frequency bandwidth. Only the simple and novel geometrical features are added in the printed pattern on the substrate. The proposed transition operates over a quite broad frequency bandwidth due to its double resonance. The two resonant frequencies are controlled by adjusting dimensions of the structure according to the required bandwidth, the reflection level and the center frequency. Two versions of the transition are designed and reliability is confirmed by experiments in the millimeter-wave band. The design frequency is 76.5 GHz. Bandwidth 12.9 GHz (16.8%) is obtained where the reflection level is lower than -30 dB. In the other design for broadband, the bandwidth for reflection level lower than -20 dB results in 24.9 GHz (32.5%). Furthermore, it is confirmed in the experiment and simulation that the center frequency is controlled from 75.3 GHz to 78.7 GHz by changing the geometry of the printed pattern.

This paper overviews the history of a class of varactor tuned bandpass filters. Since the miniaturization as well as the high performance of the tunable bandpass filters is required for the next generation mobile communication systems, the discussion is focused on the various planar type tunable filters including active configurations. Brief design concepts of various tunable filter configurations as well as their characteristics are discussed.

This paper presents novel multi-band equilateral triangular microstrip antennas (ET-MSAs) fed by an L-shaped feeding probe. Two types of the ET-MSA are proposed in this paper; they are ET-MSA with closed folded slots and open folded slots with an embedded bridge. The antenna prototypes presented in this paper assume four folded slots in which a metal strip is inserted to realize a good multi-band performance. In addition, the open folded slots, in which the metal strip inside the folded slot is connected to the ET-MSA by the embedded metal bridge, leads to miniaturize the antenna. The proposed antennas are printed on the top layer of a PTFE substrate while the L-probe is printed on the bottom one. The L-shaped probe is utilized due to its tremendous performance in providing a wideband impedance matching. Five resonant frequencies of the ET-MSAs with closed folded slots and with open folded slots are predicted by the electromagnetic simulator (IE3D) based on the method of moment, respectively. Some parametric studies have been also investigated to meet an appropriate multi-band performance. A broadside radiation pattern and gain of 3.0-7.0 dBi have been confirmed by the measurement for the entire observed frequencies. Measured results agree well with the prediction. Thus, these antenna systems are demonstrated to be useful models for a multi-band planar antenna.

In this paper a new method for the design and optimization of microstrip parallel coupled-line bandpass filters is presented which allows for the specification of frequency bandwidths and arbitrary source and load impedance transformation. The even- and odd-mode theory and the relationships between impedance, transmission and scattering matrices and their properties are used to construct a positive definite error function using the insertion losses at discrete frequencies in the pass, transition and stop bands. The dispersion relations for the coupled line are also taken into account. The minimization of the error function determines the widths, gap spacings and lengths of the coupled-line filter, for the optimum design and realization of filter specifications. The proposed filter design and optimization method is coded by computer programs and the results of simulation, fabrication and testing of sample filters together with comparisons with available full-wave analysis softwares, indicate the efficacy of the proposed method. Filter design with up to 50% bandwidth and the design of shorter lengths of coupled line sections are achievable by the proposed method in part due to the incorporation of impedance matching.

We propose here a composite right/left handed transmission line constructed by using conductor-backed coplanar strips. In this line, we can easily realize a shunt inductor without via because it has the electric-wall symmetry at the guide center. The left-handed nature is verified by both the finite difference time-domain (FDTD) and the equivalent-circuit calculations. Furthermore, we demonstrate the proposed line can easily satisfy the balanced condition for no band gap between the right-handed and the left-handed modes, and can be applied to a leaky-wave antenna, numerically and experimentally.

A nonreciprocal left-handed transmission line is proposed and investigated, which is composed of a normally magnetized ferrite microstrip line periodically loaded with inductive stubs but without capacitive loading. The circuit configuration becomes simpler than that of a nonreciprocal left-handed transmission line with both shunt inductive and series capacitive loadings. In the proposed structure, ferrite medium is employed as the substrate not only for the nonreciprocal characteristics but also for negative effective permeability that is essential to establish the left-handedness. After calculations of dispersion curves using equivalent circuit model, scattering parameters along with field patterns are estimated numerically with the help of electromagnetic simulation, and the experiments are also carried out. It is found that the band width of the proposed left-handed transmission line is relatively narrow but the structure still has the high isolation ratio of more than 30 dB.

This letter presents mutual coupling reduction in an E-plane arranged microstrip patch array fed by a triplate waveguide. Five mushroom-like electromagnetic band-gap (EBG) elements arranged in one column are embedded both between two radiating patches and between the feeding lines for suppression of the surface wave and the parallel plate mode, respectively. Validity of the proposed EBG elements is confirmed by the measurement.

A compact open-loop resonator bandpass filter is presented to suppress the spurious passband using compensated compact microstrip resonant cell (C-CMRC) feeding structure. Based on the inherently compact and stopband characteristics of the C-CMRC feeding, the proposed filters shows a better spurious rejection performance than the only open-loop resonator filter. The suppression is -57.4 dB, -49.5 dB, and -43.9 dB at the 2nd, 3rd and 4th harmonic signal separately. All the performance of proposed filters have been verified by the measured results.