In this letter, a new design of a metamaterial-based microstrip antenna is presented using triangular slots embedded on the ground plane to enhance the impedance bandwidth. To improve the impedance bandwidth of the proposed antenna, two resonant mode frequencies are closely allocated using the slotted ground without changing the radiator element. The impedance bandwidth of VSWR < 2.5 is measured at 2.43 GHz (37.6%) centered on 6.46 GHz, from 5.24 GHz to 7.67 GHz in good agreements with the simulated results.

In this paper, a novel feeding technique is proposed to feed a printed rectangular ring patch antenna that attains high gain in two bands simultaneously. The prototype antenna exhibits good impedance bandwidths satisfying ISM 2.45/5.8 GHz achieving maximum gain of 9.56 and 10.17 dBi, respectively, with a stable radiation pattern.

A new design and experimental results of a microstrip-fed ultra-wideband Fermi antenna at millimeter-wave frequencies are presented. By utilizing a new microstrip-to-CPS balun (or transition), which provides wider bandwidth than conventional planar balun, the design of microstrip-fed Fermi antenna is greatly simplified. The proposed Fermi antenna demonstrates ultra-wideband performance for the frequency range of 23 to over 58 GHz with the antenna gain of 12 to 14 dBi and low sidelobe levels. This design yields highly effective solutions to various millimeter-wave phased-arrays and imaging systems.

In this paper, the transmission and reflection properties of the microstrip line with bends are investigated using the Fourier transform and a mode-matching technique. Based on the waveguide model, the microstrip bends are modeled as the rectangular waveguides with perfect electric conducting top and bottom walls and perfect magnetic conducting side walls. Analytical closed-form expressions for transmission and reflection coefficients are developed using the residue calculus. To verify the proposed method, numerical computations are performed for comparison with 3D full-wave simulations and measurements. A quarter-wavelength transmission line scheme is also proposed to improve the signal integrity of double bend discontinuity.

A high directivity microstrip coupler suppressing leak coupling with a cancellation circuit of a Wilkinson divider is presented. The presented coupler utilizes a cancellation circuit between a coupling port and an isolation port of the conventional microstrip coupler to enhance the isolation. The cancellation circuit consists of the Wilkinson divider, the multistage attenuator, and the phase offset line. The frequency to enhance the isolation is controlled by the attenuators. As the directivity is improved without the modification of the conventional coupler, the cancellation circuit can be applied to the fabricated conventional couplers. The measured directivity of the presented 1/18 λ coupler is improved from 4.8 dB to 43.0 dB at 2.6 GHz, compared with the conventional 1/4 λ coupler with -20 dB coupling. Simultaneously, the 27.4% relative bandwidth with the 20 dB directivity is achieved.

A new comprehensive method to suppress the spurious modes in a BPF is proposed taking the multi-strip resonator BPF as an example. It consists of disturbing the resonant frequency, coupling coefficient and external Q of the higher-order modes at the same time. The designed example has shown an extraordinarily good out-of-band response in the computer simulation.

A new type of the wide-band BPF made up of an inter-digital resonator and parallel-coupled lines was proposed. The bandwidth of the inter-digital resonator becomes wider by increasing the number of fingers. The design of the parallel-coupled line was performed by optimazing the structural parameters so that the bandwidth is the same as that of the inter-digital resonator. The measured results of the combination of above elements for the BPF agreed well with the simulated ones such that the insertion loss is less than 0.67 dB and that the sharp skirt characteristics are realized by attenuation poles near the edges of the passband.

The design of microstrip bandpass filters using stepped-impedance resonators (SIRs) is examined. The passband center frequency for the WCDMA-FDD (uplink band) Japanese cellular system is 1950 MHz with a 60-MHz bandwidth. The SIR physical characteristic can be designed using a SIR characteristic chart based on second harmonic suppression. In our filter design, passband design charts were obtained through the design procedure. Tchebycheff and maximally flat bandpass filters of any bandwidth and any number of steps can be designed using these passband design charts. In addition, sharp skirt characteristics in the passband can be realized by having two transmission zeros at both adjacent frequency bands by using open-ended quarter-wavelength stubs at input and output ports. A new even-mode harmonics suppression technique is proposed to enable a wide rejection band having a high suppression level. The unloaded quality factor of the resonator used in the proposed filters is greater than 240.

We present analytical expression for inductance of a superconducting stripline, a strip sandwiched by two superconducting ground planes. In our method, we utilize the analytical formula for a perfect-conducting stripline derived by Chang in 1976. To utilize Chang's formula, we first transform the structure of a superconducting stripline into that of a perfect-conducting stripline by reducing the thicknesses of the superconducting layers. The thickness reduction is "λ coth (t/λ)" for each (upper or lower) side, where λ and t are the field penetration depth and the layer thickness, respectively. Then, we apply Chang's formula to the transformed stripline model. The calculated results are in good agreement with the numerical and experimental results.

This paper presents a simple antenna system for land vehicle communication aimed at Engineering Test Satellite-VIII (ETS-VIII) applications. The developed antenna system which designed for mounting in a vehicle is compact, light weight and offers simple satellite-tracking operation. This system uses a microstrip patch array antenna, which includes onboard-power divider and switching circuit for antenna feeding control, due to its low profile. A Global Positioning System (GPS) receiver is constructed to provide accurate information on the vehicle's position and bearing during traveling. The personal computer (PC) interfaces as the control unit and data acquisition, which were specifically designed for this application, allow the switching circuit control as well as the retrieving of the received power levels. In this research, the antenna system was firstly examined in an anechoic chamber for S parameter, axial ratio, and radiation characteristics. Satisfactory characteristics were obtained. As for beam-tracking of antenna, it was examined in the anechoic chamber with the gain above 5 dBic and the axial ratio below 3 dB. Moreover, good received power levels for tracking the ETS-VIII satellite in outdoor measurement, were confirmed.

In this paper, an indoor repeater antenna with high isolation for WCDMA application is proposed. The designed repeater has very small separation of 20 mm between the donor and server antennas. The antenna has two resonance frequencies to cover the WCDMA band from 1.92 GHz to 2.17 GHz. The fabricated antenna has VSWR below 1.5, gain over 8 dBi, and isolation between server and donor antennas less than -80 dB in the WCDMA band.

A novel bandpass filter (BPF) for an ultra-wideband (UWB) system is proposed in this letter. The BPF consists of four coplanar stripline (CPS)-to-microstrip transitions. Each transition is employed for broad electromagnetic (EM) coupling between a short-circuited CPS and an open-circuited microstrip line. The equivalent circuit model of the proposed geometry is derived and utilized in the impedance and mode matching analysis. Measured results show good agreement with the analysis and simulated ones.

This paper presents the analysis of multiconductor striplines with a finite strip thickness using the Fourier transform and mode-matching technique. The formulations, based on quasi-static approach, are developed to obtain simultaneous equations for the modal coefficients of the potential distributions between striplines. The residue calculus is applied to represent the potential distributions in convergent series form. The closed-form expressions for the self and mutual capacitances are developed analytically. Numerical computations are performed and their results show a good agreement with those of other methods.

This letter proposes a high-performance single-sided horn-shaped tapered bowtie antenna which is compact and covers more than the whole UWB frequency band. This design implements a bowtie radiating element and tapered strip-line feeder element on a single-sided dielectric substrate, which offers a measured return loss of less than -10 dB over the whole UWB frequency band of 3.0-10.8 GHz. The measured radiation pattern is bi-directional with consistent gain over the above frequency band. This compact-size design shows much enhanced performance, compared to the previously reported antenna, which is useful for UWB radar and communication applications.

In this work, errors in a ferrite core permeability dispersion measurement using a microstrip line (MSL) method, where three kinds of MSL circuits are used, are evaluated by both an electromagnetic simulation technique and experiments. The computer simulated results have shown that although the measurement errors decrease according to the diameter of the winding wire which passes through a sample ferrite core becomes larger, that is the spacing between the wire and the core gets narrower, a certain amount of error still remains. In order to overcome this problem and improve the measurement accuracy, a metal pipe electrically connected to a ground plane for shielding is placed around the wire of the non-magnetic core circuit which is one of the three MSL circuits noted above.

We have developed a high-temperature superconducting (HTS) filter with narrow bandwidth characteristic for receiver of weather radar in order to reduce interference between adjacent radar channels. To realize a filter with which a narrow bandwidth and low insertion loss are compatible, resonators with high unloaded Q (Qu) value are required. Hairpin microstrip resonators with 1.5 times wavelength were adopted to suppress the radiation loss and achieve a high Qu value. The developed HTS filter has 8-pole quasi-elliptic function response for sharp skirt characteristic. The measured frequency response of the developed filter shows center frequency of 5370 MHz, insertion loss of 2.04 dB and maximum return loss of 15 dB, which agrees with the designed responses.

In this paper, a new formulation of equal-length three-section open stubs having two zeros located on the unit circle and one zero at z=-1 (θ=π) in the Z-plane is presented. In particular, new filter configurations consisting of equal-length two-section open stubs, cascade lines, open stubs, and three-section open stubs are employed to emulate the discrete-time filters. To examine the validity of our formulation, we realized two discrete-time Chebyshev type II low-pass filters in the form of microstrip lines. The frequency responses of these two filters are measured to validate this new formulation.

A strip line broadside hybrid coupler which is tolerant to manufacturing errors in a multi-layered LTCC substrate has been developed. The tolerance to a displacement error and a thickness variation in the multi-layered LTCC substrate can be achieved by using the tandem arrangement of diagonally shifted coupled lines with adjacent ground walls. It has been demonstrated that the coupling deviation from designed characteristics in our proposed hybrid coupler is very small.

A stacked square microstrip antenna with shorting plates is proposed for wide band operation. The vswr 2 with gain at θ=0 0 dBi is achieved in the frequency range between the first and second resonant frequencies by loading the two shorting plates. The proposed antenna has bandwidth of approximately 60%.

This paper presents a new quarter-wavelength microstrip coupler compensated with a periodic sequence of floating metallic strips in the slots on the inner edges. After describing the characteristics of the coupled-line, as an example, a 15-dB coupler is designed and a high directivity of 30 dB or more in theory is obtained over a full band of a single-section coupler. Next, couplers with various coupling factors are designed, and the usefulness for very loose coupling is demonstrated. Furthermore, a three-section coupler is designed to show the effectiveness in a wide frequency range. The validity of the design concept and procedure is confirmed by electromagnetic simulations and experiments.