An aperture-coupled patch antenna on a modified-shape groundplane is proposed in this paper. It is applicable to the H-plane array without perpendicular feed structure. Availability of the depth-area under antenna-substrate is effectively improved by using radiation from the T-shaped element, while the advantage of aperture-coupled antenna in suppressing the spurious-feed-network radiation remains effective. Basic characteristics of the antenna are investigated through the numerical examination by using FDTD-method. As a result, the increased bandwidth is also obtained, which is observed as dual-resonance characteristics due to the T-shaped element and the aperture-fed patch. A H-plane array of the proposed element incorporating a probe-fed patch antenna is also presented to show an potential as a polarization diversity antenna.

A new microstrip compatible phase shifter circuit is introduced. The phase shifter uses a strip-type electromagnetic bandgap (EBG) substrate in place of the solid metal ground plane. Such EBG substrates, when made of ferroelectric materials, can produce variable phase constants useful for phase shifter applications. Test models using two different EBG substrates with dielectric constants of 9.2 and 10.2 showed 44.5 degrees of phase difference with 1.7 dB of added insertion loss at 10 GHz from a line originally 504 degrees long.

Periodically nonuniform coupled microstrip line (PNC-ML) loaded with transverse slits is characterized using the fullwave method of moments and short-open calibration technique. Guided-wave characteristics of both even- and odd-modes are thoroughly investigated in terms of two extracted per-unit-length transmission parameters, i.e., phase constants and characteristic impedances. As such, frequency-dependent coupling between the lines of the finite-extended PNCML is exposed via two dissimilar impedances. Meanwhile, two phase constants try to be equalized at a certain frequency by properly adjusting the slit depth and periodicity, aiming at realizing the transmission zero. Further, equivalent J-inverter network parameters of this finite-length PNCML are derived to reveal the relationship between the transmission zero and harmonic resonance. By allocating this zero to the frequency twice the fundamental passband, one-stage and two-stage PNCML filters are then designed, fabricated and measured to showcase the advantageous capacity of the proposed technique in harmonic suppression.

In this paper a novel dielectric resonator (DR) bandpass filter (BPF) with flexible arrangement of attenuation poles is proposed. This DR filter is similar to a conventional DR filter except adding a microstrip line below a DR, which not only shifts the location of attenuation poles, but also improves skirt characteristics. The duplexer with the proposed DR BPF has been yielded better isolation and sharper skirt behavior than that with a conventional DR filter. The implemented duplexer has shown a good performance and been well agreed with the simulation.

This paper presents an analytical model for the electromagnetic radiation in multi-microstrip lines covering the frequency range from 30 MHz to 1 GHz. The radiated emissions of multi-microstrip structure can be divided into the summation of radiated emissions of multi-individual microstrip structures. It is done by modelling the imperfect ground effect of the PCBs. Here we present a circuit model based on traditional transmission lines (TMLs) model. For more accurate analysis of the imperfect ground effect in multi-microstrip lines, we will divide the equivalent circuit model into N sections, based on transverse electromagnetic (TEM) assumption, to estimate the electromagnetic interference (EMI) of multi-microstrip lines. The quantitative value of induced current distribution along the ground return path depends on the physical size, geometry and length of ground trace. Measured data are presented to confirm the results of numerical analysis and the computer simulations with a software package based on the Finite Element Method. A knowledge of EMI source mechanism and their relationship to layout geometries is necessary to determine the essential features that must be modelled to estimate emissions in PCBs design.

This paper discusses the design, fabrication, and measurement of four L-shaped-slot microstrip patch antenna for HiperLan2. The prototype consists of four L-shaped slots. To obtain suitable bandwidth, the form layer is inserted between the ground plane and substrate. The design considers various important factors that include the four L-slot's length, width, position, air-gap height, and feed-point position. Once these factors are optimized, a four L-shaped slot microstrip patch antenna is fabricated and measured. The measured results of the fabricated four L-shaped slot antenna are as follows: resonant frequency is 5.35 GHz, bandwidth is approximately 8.1% (VSWR < 2.0), and gain is 8-9 dBi. The experimental far-field patterns are stable across the pass band. The 3 dB bandwidth in Elevation and Azimuth are 69and 62, respectively.

The electric currents on the upper, lower and side surfaces of the patch conductor in a circular microstrip antenna are calculated by using the integral equation method and the characteristic between the electric currents on the upper and lower surfaces is compared. The integral equation is derived from the boundary condition that the tangential component of the total electric field due to the electric currents on the upper, lower and side surfaces of the patch conductor vanishes on the upper, lower and side surfaces of the patch conductor. The electric fields are derived by using Green's functions in a layered medium due to a horizontal and a vertical electric dipole on those surfaces. The result of numerical calculation shows that the electric current on the lower surface is much bigger than that on the upper surface and the input impedance of microstrip antenna depends on the electric current on the lower surface.

In this study, a multiple U-shaped slot microstrip patch antenna for application to the 5 GHz band is designed and fabricated. To obtain sufficient bandwidth in the operating band, foam is inserted between the substrate and ground plane, the type of form is styrofoam, the coaxial probe source is used, and the position of the probe shift is adjusted from the center to the left. The measured result (5.02-5.955 GHz) of the fabricated antenna satisfies the conditions of VSWR < 2.0 in 5 GHz band (5.15-5.35 GHz, 5.47-5.725 GHz, 5.725-5.825 GHz), gain of 3.88-9.28 dBi, and broad radiation pattern.

2 GHz band electrically tunable superconducting microstrip line band-pass filter was developed. The tunable filter used a thin interdigital electrode. The dielectric distribution of SrTiO3 substrate included a calculated nonlinear effect of the electrode and ferroelectric material. As a result, the tunable microstrip line filter design with interdigital electrode enabled calculation by the finite element method and the moment method. The tunable filter with a measured unloaded Q factor of 9700 and a frequency shift of 1.25 MHz was obtained.

A high temperature superconductor (HTS) filter is designed and measured at 1.93 GHz, using microstrip half-wavelength spiral resonators. Resonant and coupling characteristics of miniaturized microstrip spiral resonators are investigated first. Then a 4-pole Chebyshev bandpass filter with a very narrow passband (4.1 MHz) is designed and realized using microstrip spiral resonators. The filter is fabricated using HTS YBCO films deposited on a LaAlO3 substrate. The measured frequency response of the filter agrees reasonably with the specifications, and shows that the filter owns excellent property of spurious resonance rejection over a wide frequency range.

At frequencies currently used by mobile communications, many of the microstrip half-wavelength resonators are too large to realize miniaturized filters. For this reason, very small-sized microstrip spiral resonators and filters, using high-temperature superconductors (HTS), have been studied recently. In this paper, the resonant and coupling characteristics of microstrip G-type and S-type spiral resonators are investigated first by using an electromagnetic simulator. Then small-sized 4-pole, 8-pole, and 16-pole Chebyshev bandpass filters using S-type spirals are designed, respectively, with a midband frequency f0 = 1.93 GHz. The frequency responses of the filters satisfy well the desired specifications, and the measured frequency response of the 8-pole HTS filter agrees well with the theoretical prediction.

This paper presents a computer-aided design procedure of simulated annealing algorithm to optimize dual-wideband microstrip line filters with symmetrical at least 500 MHz bandwidths respectively. This method demonstrates the superiority of designing microstrip line dual-band filters. The value of characteristic impedances and electrical lengths of transmission lines synthesizing 2.4 GHz and 5.2 GHz dualband filters with a single input and a single output are adjusted to the annealing process by the optimization algorithm. The fabricated dual-wideband spectral transmittance and reflectance curves of these filters applying this method all effectively achieved desired high performances and resulted in a lower cost dual-band filters and open the way to commercial mass production. The method is applicable not only in 2.4 GHz and 5.2 GHz, but can be applied to any other multi-frequency bands.

A detailed investigation of the electromagnetic field distributions in high frequency printed circuits and high-speed interconnects is very useful for physical understanding, studies of electromagnetic coupling effects for EMC and EMI and for optimization of electromagnetic circuit designs. The aim of this paper is to show how to measure the electric field distributions in electromagnetic circuits. An electromagnetic analysis for microstrip-line circuits is carried out by using a finite-difference time domain technique and its measurement is carried out by using a small probe antenna. The measurement results are in fairly good agreement with those of the numerical analysis using the FDTD method. Thus, the measurement system offers a valid means for predictions in the theoretical analysis of more complicated discontinuity problems.

A low-loss serial power combiner using suspended stripline is described. It consists of novel broadside-coupled directional couplers which have shunt capacitances at the edges of the coupled sections. These additional shunt capacitances compensate for poor directivities of the couplers because of inhomogeneous dielectric in suspended stripline structure. The fabricated three-way power combiner has achieved good performance with insertion loss less than 0.23 dB over a bandwidth of 10% in 2 GHz band.

A mode transformer between the NRD guide and the vertical strip line was developed and applied to the right angle corner, T-junction, and 3-port junction at 60 GHz. Emphasis was placed on a fully CAD-based design procedure by using an electromagnetic field simulator. Agreement between the simulated and measured performances of the junction circuit was obtained, and thus the validity of the design procedure was confirmed. A well-balanced transmission coefficient of the 3-port junction, found to be 4 0.5 dB, was observed in the bandwidth of 2 GHz around a center frequency of 60 GHz.

This paper treats multi-way microstrip power dividers composed of multi-step, multi-furcation, and corners. Since the design procedure is founded on the planar circuit approach in combination with the segmentation method, optimization of the circuit configuration can be performed in a reasonable short computation time when applying the Powell's optimization algorithm. Actually, broadband 3- and 4-way power dividers with mitered bends are designed, and fractional bandwidths of about 90% and 100% are realized for the power-split imbalance less than 0.2 dB and the return loss better than -20 dB, respectively. The validity of the design results is confirmed by an EM-simulator (HFSS) and experiments.

Novel microstrip lowpass filters are developed with reduced size and significantly improved stopband characteristics. After introducing quarter-wavelength open stubs, we get one or two transmission zeros in the stopband. By folding the high impedance microstrip lines, we reduce the size of the filter. Three-pole and five-pole lowpass filters are designed, and their measured frequency responses agree well with theoretical predictions.

In this paper, a 20 GHz push-push oscillator using a ring resonator is proposed. The push-push oscillator adopts "dipole resonator push-push oscillator" circuit scheme, in which a common resonator plays two roles of frequency determining and power combining, and then the additional power combiner circuit required in conventional push-push oscillators can be eliminated. This kind of push-push oscillators has the advantages of the easy circuit design, the simple circuit configuation and the miniaturization of the circuit size. The output power is +4.5 dBm at the frequency of 20.34 GHz (2f0) with the phase noise of -98 dBc/Hz at the offset frequency of 1 MHz, and a high suppression of the undesired the fundamental frequency signal (f0) of -33 dBc is obtained.

This paper presents a dual-frequency microstrip antenna for both 2 GHz and 5 GHz for a dual-band receiver. For a simple structure and low cost design, the microstrip feed circuit is designed on the same substrate as the antenna elements. Each antenna element is directly fed by the microstrip line, and the open stubs are loaded on the feed line of 2 GHz to suppress the higher order mode resonances between 2 GHz and 5 GHz. The feed line length of each antenna is adjusted so as to change it to the open condition at the other element frequency at the feed point. In addition, we propose the antenna structure in which two antenna elements for 2 GHz are split and placed at either sides of the 5 GHz antenna to coincide with the center positions of each antenna element. We investigate the proposed antenna by calculations and measurements to show the combiner free design for the dual band antenna.

We propose a new cell configuration which newly employs discharge deactivation film (DDF). DDF is formed on MgO surface in stripe figure to cover it around the boundary of neighboring display lines. DDF prevents discharge cross talk between the lines even in case of stripe rib structure by virtue of its low secondary electron emission coefficient (γi). DDF also makes better address discharge response because it presumably moves address discharge closer to the surface dischage gap. On behalf of mass productivity for large size PDPs DDF is formed by simple screen-printing and firing method. And it consists of very fine Al2O3 grains without any inorganic binder. Such DDF is visually transparent and then helpful for high luminance and luminous efficiency. In addition to it, such DDF is presumably equipped with gas purifying character and then helpful for deep blue color and good white color balance accordingly. Further, DDF combined with sustain electrodes in specific figure which we call "CAPABLE DDF" brings about so high luminous efficiency for stripe rib structure as it may surpass box rib one. This probably means that vertically open discharge space in stripe rib structure is advantageous for high luminous efficiency. In our latest work for 46 inch-high definition PDPs, 2.1 lm/W and 1200 cd/m2 were both achieved under practical driving condition. Still it will be as high as 2.4 lm/W if each sustain electrode is shared by neighboring display lines. CAPABLE DDF allows more tolerance in DDF printing process. It also makes optical cross talk negligible even in stripe rib structure. And its durability against long time operation proved to have no specific problem. This presumably means that re-landing of sputtered MgO never reaches DDF surface. We believe this new technology can promise the future of stripe rib.