Aiming at the problem of “energy hole” caused by random distribution of nodes in large-scale wireless sensor networks (WSNs), this paper proposes an adaptive energy-efficient balanced uneven clustering routing protocol (AEBUC) for WSNs. The competition radius is adaptively adjusted based on the node density and the distance from candidate cluster head (CH) to base station (BS) to achieve scale-controlled adaptive optimal clustering; in candidate CHs, the energy relative density and candidate CH relative density are comprehensively considered to achieve dynamic CH selection. In the inter-cluster communication, based on the principle of energy balance, the relay communication cost function is established and combined with the minimum spanning tree method to realize the optimized inter-cluster multi-hop routing, forming an efficient communication routing tree. The experimental results show that the protocol effectively saves network energy, significantly extends network lifetime, and better solves the “energy hole” problem.

Recent studies have shown that concurrent transmission with precise time synchronization enables reliable and efficient flooding for wireless networks. However, most of them require all nodes in the network to forward packets a fixed number of times to reach the destination, which leads to unnecessary energy consumption in both one-to-one and many-to-one communication scenarios. In this letter, we propose G1M address this issue by reducing redundant packet forwarding in concurrent transmissions. The evaluation of G1M shows that compared with LWB, the average energy consumption of one-to-one and many-to-one transmission is reduced by 37.89% and 25%, respectively.

In wireless sensor networks (WSNs), wireless power transfer (WPT) has been studied as an energy-harvesting technique for prolonging their network lifetime. The WPT can supply power resources to sensor nodes (SNs) wirelessly, however, the reception (harvesting) power at SNs depends on their distance from a WPT equipment (WPTE), leading to the location-dependent non-uniformity in the reception power among SNs. For the fixed-located WPTE, SNs distant from the WPTE suffer from insufficient reception power. To handle this problem, this paper proposes a novel network structure introducing multiple hybrid access points (HAPs), which equip two functions of conventional cluster head function, including data collection and relay transmission, and WPT function. Then, these HAPs take terms providing both functions. By periodically rotating the HAP providing the WPT function, the location of the WPTE can be changed, which reduces the non-uniformity in the SN reception power. Also, this paper proposes a clustering scheme based on the residual power at SNs to reduce their power depletion under the proposed network structure. The evaluation results through computer simulation show that the proposed system reduces the non-uniformity in the SN reception power and the power depletion at the SNs and then improves the data collection rate, compared with the conventional systems.

As an emerging technology, device-free localization (DFL) using wireless sensor networks to detect targets not carrying any electronic devices, has spawned extensive applications, such as security safeguards and smart homes or hospitals. Previous studies formulate DFL as a classification problem, but there are still some challenges in terms of accuracy and robustness. In this paper, we exploit a generalized thresholding algorithm with parameter p as a penalty function to solve inverse problems with sparsity constraints for DFL. The function applies less bias to the large coefficients and penalizes small coefficients by reducing the value of p. By taking the distinctive capability of the p thresholding function to measure sparsity, the proposed approach can achieve accurate and robust localization performance in challenging environments. Extensive experiments show that the algorithm outperforms current alternatives.

This study proposes a design method for a rectifier circuit that can be rapidly charged by focusing on the design-load value of the circuit and the load fluctuation of a storage capacitor. The design-load value is suitable for rapidly charging the capacitor. It can be obtained at the lowest reflection condition and estimated according to the circuit design. This is a conventional method for designing the rectifier circuit using the optimum load. First, we designed rectifier circuits for the following three cases. The first circuit design uses a load set to 10 kΩ. The second design uses a load of 30 kΩ that is larger than the optimum load. The third design utilizes a load of 3 kΩ. Then, we measure the charging time to design the capacitor on each circuit. Consequently, the results show that the charge time could be shortened by employing the design-load value lower than that used in the conventional design. Finally, we discuss herein whether this design method can be applied regardless of the rectifier circuit topology.

In this paper, we advocate applying the concept of content-based wake-up to distributed estimation in wireless sensor networks employing wake-up receivers. With distributed estimation, where sensing data of multiple nodes are used for estimating a target observation, the energy consumption can be reduced by ensuring that only a subset of nodes in the network transmit their data, such that the collected data can guarantee the required estimation accuracy. In this case, a sink needs to selectively wake up those sensor nodes whose data can contribute to the improvement of estimation accuracy. In this paper, we propose wake-up signaling called estimative sampling (ES) that can selectively activate the desired nodes by using content-based wake-up control. The ES method includes a mechanism that dynamically searches for the desired nodes over a distribution of sensing data. With numerical results obtained by computer simulations, we show that the distributed estimation with ES method achieves lower energy consumption than conventional identity-based wake-up while satisfying the required accuracy. We also show that the proposed dynamic mechanism finely controls the trade-off between delay and energy consumption to complete the distributed estimation.

To tackle the distributed power optimization problems in wireless sensor networks localization systems, we model the problem as a hierarchical game, i.e. a multi-leader multi-follower Stackelberg game. Existing researches focus on the power allocation of anchor nodes for ranging signals or the power management of agent nodes for cooperative localization, individually. However, the power optimizations for different nodes are indiscerptible due to the common objective of localization accuracy. So it is a new challenging task when the power allocation strategies are considered for anchor and agent nodes simultaneously. To cope with this problem, a hierarchical game is proposed where anchor nodes are modeled as leaders and agent nodes are modeled as followers. Then, we prove that games of leaders and followers are both potential games, which guarantees the Nash equilibrium (NE) of each game. Moreover, the existence of Stackelberg equilibrium (SE) is proved and achieved by the best response dynamics. Simulation results demonstrate that the proposed algorithm can have better localization accuracy compared with the decomposed algorithm and uniform strategy.

In the statistic en-route filtering, each report generation node must collect a certain number of endorsements from its neighboring nodes. However, at some point, a node may fail to collect an insufficient number of endorsements since some of its neighboring nodes may have dead batteries. This letter presents a report generation method that can enhance the generation process of sensing reports under such a situation. Simulation results show the effectiveness of the proposed method.

Mobile wireless sensor networks (WSNs) are facing threats from malicious nodes that disturb packet transmissions, leading to poor mobile WSN performance. Existing studies have proposed a number of methods, such as decision tree-based classification methods and reputation based methods, to detect these malicious nodes. These methods assume that the malicious nodes follow only pre-defined attack models and have no learning ability. However, this underestimation of the capability of malicious node is inappropriate due to recent rapid progresses in machine learning technologies. In this study, we design reinforcement learning-based malicious nodes, and define a novel observation space and sparse reward function for the reinforcement learning. We also design an adaptive learning method to detect these smart malicious nodes. We construct a robust classifier, which is frequently updated, to detect these smart malicious nodes. Extensive experiments show that, in contrast to existing attack models, the developed malicious nodes can degrade network performance without being detected. We also investigate the performance of our detection method, and confirm that the method significantly outperforms the state-of-the-art methods in terms of detection accuracy and false detection rate.

Distributing codes to specific target sensors in order to fix bugs and/or install a new application is an important management task in WSNs (Wireless Sensor Networks). For the energy efficient dissemination of such codes to specific target sensors, it is required to select the minimum required number of forwarders with the fewest control messages. In this paper, we propose a novel RPL (Routing Protocol for Low-power and lossy networks)-based tree construction scheme for target-specific code dissemination, which is called R-TCS. The main idea of R-TCS is that by leveraging the data collection tree created by a standard routing protocol RPL, it is possible to construct the code dissemination tree with the minimum numbers of non-target sensors and control messages. Since by creating a data collection tree each sensor exchanges RPL messages with the root of the tree, every sensor knows which sensors compose its upwards route, i.e. the route towards the root, and downwards route, i.e. the route towards the leaves. Because of these properties, a target sensor can select the upward route that contains the minimum number of non-target sensors. In addition, a sensor whose downward routes do not contain a target sensor is not required to transmit redundant control messages which are related to the code dissemination operation. In this way, R-TCS can reduce the energy consumption which typically happens in other target-specific code dissemination schemes by the transmission of control messages. In fact, various performance evaluation results obtained by means of computer simulations show that R-TCS reduces by at least 50% energy consumption as compared to the other previous known target-specific code dissemination scheme under the condition where ratio of target sensors is 10% of all sensors.

The flexibility of wireless communication makes it more and more widely used in industrial scenarios. To satisfy the strict real-time requirements of industry, various wireless methods especially based on the time division multiple access protocol have been introduced. In this work, we first conduct a mathematical analysis of the network model and the problem of minimum packet loss. Then, an optimal Real-time Scheduling algorithm based on Backtracking method (RSBT) for industrial wireless sensor networks is proposed; this yields a scheduling scheme that can achieve the lowest network packet loss rate. We also propose a suboptimal Real-time Scheduling algorithm based on Urgency and Concurrency (RSUC). Simulation results show that the proposed algorithms effectively reduce the rate of the network packet loss and the average response time of data flows. The real-time performance of the RSUC algorithm is close to optimal, which confirms the computation efficiency of the algorithm.

Sensor-data gathering using multi-hop connections in a wireless sensor network is being widely used, and a tree topology for data gathering is considered promising because it eases data aggregation. Therefore, many sensor-tree-creation algorithms have been proposed. The sensors in a tree, however, generally run on batteries, so long tree lifetime is one of the most important factors in collecting sensor data from a tree over a long period. It has been proven that creating the longest-lifetime tree is a non-deterministic-polynomial complete problem; thus, all previously proposed sensor-tree-creation algorithms are heuristic. To evaluate a heuristic algorithm, the time complexity of the algorithm is very important, as well as the quantitative evaluation of the lifetimes of the created trees and algorithm speed. This paper proposes an algorithm called assured switching with accurate graph optimization (ASAGAO) that can create a sensor tree with a much longer lifetime much faster than other sensor-tree-creation algorithms. In addition, it has much smaller time complexity.

To efficiently collect sensor readings in cluster-based wireless sensor networks, we propose a structural compressed network coding (SCNC) scheme that jointly considers structural compressed sensing (SCS) and network coding (NC). The proposed scheme exploits the structural compressibility of sensor readings for data compression and reconstruction. Random linear network coding (RLNC) is used to re-project the measurements and thus enhance network reliability. Furthermore, we calculate the energy consumption of intra- and inter-cluster transmission and analyze the effect of the cluster size on the total transmission energy consumption. To that end, we introduce an iterative reweighed sparsity recovery algorithm to address the all-or-nothing effect of RLNC and decrease the recovery error. Experiments show that the SCNC scheme can decrease the number of measurements required for decoding and improve the network's robustness, particularly when the loss rate is high. Moreover, the proposed recovery algorithm has better reconstruction performance than several other state-of-the-art recovery algorithms.

The compressive sensing has been applied to develop an effective framework for simultaneously localizing multiple targets in wireless sensor networks. Nevertheless, existing methods implicitly use analog measurements, which have infinite bit precision. In this letter, we focus on off-grid target localization using quantized measurements with only several bits. To address this, we propose a novel localization framework for jointly estimating target locations and dealing with quantization errors, based on the novel application of the variational Bayesian Expectation-Maximization methodology. Simulation results highlight its superior performance.

This paper focuses on on-demand wireless sensor networks (WSNs) where a wake-up receiver is installed into each node. In on-demand WSNs, each node sends a wake-up signal including a wake-up ID assigned to a specific destination node in order to remotely activate its main radio interface. This wake-up control helps each node to reduce energy consumed during idle periods, however, the wake-up signal transmitted before every data transmission results in overhead, which degrades communication quality and increases energy consumption at each sender node. In order to reduce the overhead for wake-up control, in this paper, we propose three schemes. First, we propose a scheme called Double Modulation (DM), where each node embeds the sensing data to be transmitted into the payload field of a wake-up signal. The destination interprets the wake-up message differently depending on its wake-up state: if it is in a sleep state, it treats the message as a wake-up signal, otherwise it extracts the sensing data from the detected message. Second, we propose a scheme called Overhearing (OH), where each node observes the frames transmitted by a destination node and suppresses the transmission of wake-up signal when detecting the active state of their destination. Finally, we propose a hybrid scheme that combines OH and DM schemes. Our simulation results show that the proposed schemes can effectively reduce the negative impact of wake-up overhead, and significantly improve data collection rate and energy-efficiency in comparison to on-demand WSN without the proposed schemes.

Topological inference is the foundation of network performance analysis and optimization. Due to the difficulty of obtaining prior topology information of wireless sensor networks, we propose routing topology inference, RTI, which reconstructs the routing topology from source nodes to sink based on marking packets and probing locally. RTI is not limited to any specific routing protocol and can adapt to a dynamic and lossy networks. We select topological distance and reconstruction time to evaluate the correctness and effectiveness of RTI and then compare it with PathZip and iPath. Simulation results indicate that RTI maintains adequate reconstruction performance in dynamic and packet loss environments and provides a global routing topology view for wireless sensor networks at a lower reconstruction cost.

The introduction of a drone-based mobile sink into wireless sensor networks (WSNs), which has flexible mobility to move to each sensor node and gather data with a single-hop transmission, makes cumbersome multi-hop transmissions unnecessary, thereby facilitating data gathering from widely-spread sensor nodes. However, each sensor node spends significant amount of energy during their idle state where they wait for the mobile sink to come close to their vicinity for data gathering. In order to solve this problem, in this paper, we apply a wake-up receiver to each sensor node, which consumes much smaller power than the main radio used for data transmissions. The main radio interface is woken up only when the wake-up receiver attached to each node detects a wake-up signal transmitted by the mobile sink. For this mobile and on-demand data gathering, this paper proposes a route control framework that decides the mobility route for a drone-based mobile sink, considering the interactions between wake-up control and physical layer (PHY) and medium access control (MAC) layer operations. We investigate the optimality and effectiveness of the route obtained by the proposed framework with computer simulations. Furthermore, we present experimental results obtained with our test-bed of a WSN employing a drone-based mobile sink and wake-up receivers. All these results give us the insight on the role of wake-up receiver in mobile and on-demand sensing data gathering and its interactions with protocol/system designs.

This paper proposes Code-Modulated Synchronized (CMS) -OOK modulation scheme for normally-off wireless sensor networks, and demonstrates the operation of the transmitter for the CMS-OOK using 65nm SOTB (Silicon-On Thin Buried Oxide) CMOS technology. Based on investigating RF characteristics of SOTB CMOS, analog part of a CMS-OOK transmitter was designed, fabricated and evaluated in combination with based-FPGA digital part. With code modulation and controlling the carrier frequency by body bias of the SOTB devices, the spectrum of a CMS-OOK transmitter output is widen to achieve -62dBm/MHz peak power spectrum density at 15 MHz bandwidth. Chip of analog part on-board is supplied by 1V for power amplifier and 0.75V for the rest. It consumes average 83µW according to 83nJ/bit at 1kbps data transmission.

In this paper, the problem of lifetime extension of wireless sensor networks (WSNs) with redundant sensor nodes deployed in 3D vegetation-covered fields is modeled, which includes building communication models, network model and energy model. Generally, such a problem cannot be solved by a conventional method directly. Here we propose an Artificial Bee Colony (ABC) based optimal grouping algorithm (ABC-OG) to solve it. The main contribution of the algorithm is to find the optimal number of feasible subsets (FSs) of WSN and assign them to work in rotation. It is verified that reasonably grouping sensors into FSs can average the network energy consumption and prolong the lifetime of the network. In order to further verify the effectiveness of ABC-OG, two other algorithms are included for comparison. The experimental results show that the proposed ABC-OG algorithm provides better optimization performance.

In this paper we propose the Zone-based Energy Aware data coLlection (ZEAL) protocol. ZEAL is designed to be used in agricultural applications for wireless sensor networks. In these type of applications, all data is often routed to a single point (named “sink” in sensor networks). The overuse of the same routes quickly depletes the energy of the nodes closer to the sink. In order to minimize this problem, ZEAL automatically creates zones (groups of nodes) independent from each other based on the trajectory of one or more mobile sinks. In this approach the sinks collects data queued in sub-sinks in each zone. Unlike existing protocols, ZEAL accomplish its routing tasks without using GPS modules for location awareness or synchronization mechanisms. Additionally, ZEAL provides an energy saving mechanism on the network layer that puts zones to sleep when there are no mobile sinks nearby. To evaluate ZEAL, it is compared with the Maximum Amount Shortest Path (MASP) protocol. Our simulations using the ns-3 network simulator show that ZEAL is able to collect a larger number of packets with significantly less energy in the same amount of time.