Newly developed multi-layer inductors on GaAs three-dimensional MMICs are presented. We analyzed single-, double-, triple-, and quadruple-layer stacked-type inductors in what may be the first report on inductors on a GaAs MMIC with three or more layers. The performance of single- and multi-layer inductors was measured and calculated by electromagnetic field simulation. The multi-layer inductors produce 2-11 times higher inductance than that of conventional inductors on 2D-MMICs although they are the same size. This means that the proposed multi-layer inductors have smaller areas with the same inductances than those of conventional inductors. We also conducted the first-ever investigation of how performance factors such as parasitic capacitance, Q-factor, and self-resonant frequency are degraded in multi-layer inductors vis-a-vis those of conventional inductors. A microwave amplifier using multi-layer inductors was demonstrated and found to reduce circuit size by 20%.

In this paper we describe and experimentally validate a dual-band digital predistortion (DPD) model we propose that takes account of the intermodulation and harmonic distortion produced when the center frequencies of input bands have a harmonic relationship. We also describe and experimentally validate our proposed novel dual-band power amplifier (PA) linearization architecture consisting of a single feedback loop employing a dual-band mixer. Experiment results show that the DPD linearization the proposed model provides can compensate for intermodulation and harmonic distortion in a way that the conventional two-dimensional (2-D) DPD approach cannot. The proposed feedback architecture should make it possible to simplify analog-to-digital converter (ADC) design and eliminate the time lag between different feedback paths.

We present a highly integrated quasi-millimeter-wave receiver MMIC that integrates 22 circuits in a 3 2.3 mm area using three-dimensional MMIC (3D-MMIC) technology. The MMIC achieves low noise (3 dB) and high gain (41 dB) at 26 GHz by using an on-chip image reject filter. It integrates a multiply-by-eight (X8) local oscillator (LO) chain with the IF frequency of the 2.4 GHz band and can use low-cost voltage-controlled oscillators (VCOs) and demodulators in a 2–3 GHz frequency band. Multilayer inductors contribute to the miniaturization especially in a 2–12 GHz frequency band. Furthermore, it achieves a high dynamic range by using two step attenuators with a new built-in inverter using an N-channel depression field-effect transistor (FET). The power consumption of the MMIC is only 450 mW.

In the recently developed Flexible Wireless System (FWS), the same platform needs to deal with different wireless systems. This increases nonlinear distortion in its wideband power amplifier (PA) because the PA needs to concurrently amplify multi-band signals. By taking higher harmonics as well as inter- and cross-modulation distortion into consideration, we have developed a method to analytically evaluate the adjacent channel leakage power ratio (ACPR) and error vector magnitude (EVM) on the basis of the PA's nonlinear characteristics. We devise a novel method for modeling the PA amplifying dual-band signals. The method makes it possible to model it merely by performing a one-tone test, making use of the Volterra series expansion and the general Wiener model. We then use the Mehler formula to derive the closed-form expressions of the PA's output power spectral density (PSD), ACPR, and EVM. The derivations are based on the assumption that the transmitted signals are complex Gaussian distributed in orthogonal frequency division multiplexing (OFDM) transmission systems. We validate the method by comparing measurement and simulation results and confirm it can appropriately predict the ACPR and EVM performance of the nonlinear PA output with OFDM inputs. In short, the method enables correct modeling of a wideband PA that amplifies dual-band signals merely by conducting a one-tone test.

An S-band linearizer was developed using GaAs MMIC technology. We call it the even-order-distortion-implemented intermodulation distortion controller (EODIC). EODIC uses even-order intermodulation distortion (IM) components in the second harmonic frequency band to control its IM components in the fundamental frequency band. EODIC is a suitable tool to compensate near-saturated high power amplifiers (HPAs). We developed an EODIC using MMIC technology. This paper describes the principle of EODIC and then introduces the EODIC MMIC in detail. This paper also presents the IM reduction performance of an EODIC in a near-saturated HPA.

This paper presents an extremely low-profile front-end configuration for a base station at quasi-millimeter wave band. It consists of integrated modules of patch antennas and substrate integrated waveguide filters using two printed circuit boards, and transmitter modules using compact GaAs pHEMT three-dimensional monolithic millimeter-wave integrated circuits. The transmitter modules are located around the integrated modules. This is because the proposed front-end configuration can attain extremely low profile, and band-pass filtering performance at quasi-millimeter wave band. As a demonstration of the proposed configuration, 26-GHz-band 4-by-4 elements front-end module is fabricated and tested. The fabricated module has the thickness of about 1 cm, while that offers the attenuation of more than 30 dB with 2 GHz offset from 26 GHz. The proposed configuration can provide base station that can be effective in offering sub-millimeter wave and millimeter-wave bands broadband services for 5G mobile communications systems.

A highly integrated frequency quadrupler MMIC that uses three-dimensional MMIC (3D-MMIC) technology is presented. It consists of four driver amplifiers, two doublers, and a 2-band elimination filter. These seven circuits are integrated in only a 2.36 mm2 area. The filter sufficiently suppresses spurious output components. The third and fifth harmonic components, which are the spurious components nearest to the desired component, are well suppressed. The desired/undesired ratio is about 40 dB. The driver amplifiers make the quadrupler output a constant power of the desired multiplied signal under low input power. The MMIC supplies +5 dBm of the fourth harmonic component in the input power range from -10 dBm to +5 dBm. The power dissipation of the MMIC is only 160 mW.

We propose a novel adaptive linearization technique for a balanced-amplifier array. The technique uses the specific intermodulation distortions (IMDs) at the output ports in the array. The detected IMD power level can be used to optimize the linearizer's characteristics. Because the design does not need as many power detectors and carrier cancel loops as it does amplifiers, we were able to successfully miniaturize the array-antenna system. This paper describes the principles, verified both experimentally and mathematically for a 4-port amplifier array.

Novel multi-band mixers that can receive multiple band signals concurrently are proposed and evaluated. The mixers achieve independent gain control through novel relative power control method of the multiple local oscillator (LO) signals. Linear control is also achieved through multiple LO signal input with total LO power control. Theoretical analysis shows that odd-order nonlinearity components of the multiple LO signals support linear conversion gain control. Dual- and triple-band tests are conducted using typical three MOSFET mixers fabricated by a 0.25 µm SiGe BiCMOS process. Measurements confirm over 40 dB independent control of conversion gain, linear control achieved through LO input power control. The proposed mixers have high input linearity with a 5 dBm output third intercept point. A method is also proposed to reduce interference caused by mixing between multiple LO signals.