An effective way to boost power gain without noise figure degradation in a cascode low noise amplifier (LNA) is demonstrated at 4 GHz using 0.35 µm SiGe HBT technology. This approach maintains the same current consumption because a low-pass π-type LC matching network is inserted in the inter-stage of a conventional cascode LNA. 5 dB gain enhancement with no noise figure degradation at 4 GHz is observed in the SiGe HBT LNA with inter-stage matching.

Three distortion reduction filters for radio-on-fiber systems are proposed and evaluated from the standpoint of improvements in in-band third order intermodulation (IM3) components (spurious components), insertion loss, temperature stability and so on. The basic filter configuration includes optical comb filter, RF (radiowave frequency) comb filter, and RF dual band rejection filter (DBRF). Experiments are conducted at 2 GHz band for frequency separation Δf=5 MHz and 100 MHz in the temperature range of -10 to +50. These filters can reduce IM3 components even in the saturation region, unlike conventional linearizers. An optical comb filter can reduce IM3 components more than 20 dB and noise level around 10 dB if its polarization controller is properly adjusted, but its insertion loss is large and stability against vibration is very poor. The proposed RF comb filter and RF-DBRF can reduce IM3 components by more than 20 dB and noise level by more than 3 dB. Their stability against vibration and temperature change is good, and insertion losses are 1-2 dB for Δf=100 MHz.

Simultaneous all-optical frequency up/downconversion technique utilizing a single semiconductor optical amplifier Mach-Zehnder interferometer (SOA-MZI) for full-duplex WDM radio over fiber (RoF) applications is presented. Using this technique, error-free simultaneous upconversion and downconversion of RoF signals with a finite-length single mode fiber were experimentally demonstrated. The results show the potential of the proposed scheme for use in a cost-effective full-duplex WDM RoF link.

Next generation free electron lasers aim to generate x-ray pulses with pulse durations down to 30 fs, and possibly even sub-fs. Synchronization of various stages of the accelerator and the probe laser system to the x-ray pulses with stability on the order of the pulse width is necessary to make maximal use of this capability. We are developing an optical timing synchronization system in order to meet this challenge. The scheme is based on generating a train of short optical pulses, with a precise repetition frequency, from a mode-locked laser oscillator and distributed via length-stabilized optical fibers to points requiring synchronization. The timing information is embedded in the repetition frequency and its harmonics. A significant advantage of the optical synchronization system is that multiple mode-locked Ti:sapphire seed oscillators typically present in an accelerator facility can be replaced by the master mode-locked fiber laser. In this paper, we briefly review progress on the development of the synchronization system and then discuss the implementation of this new possibility. Several technical issues related to this approach are analyzed.

A microwave photonic mixer utilizing an InGaAs photoconductor for radio over fiber applications is proposed and fabricated. Static and dynamic characteristics of the fabricated microwave photonic mixer were investigated. The microwave photonic mixer showed an optical bandwidth of approximately 300 MHz and a uniform conversion loss characteristic for the electrical input frequency up to 20 GHz.

A 10-GHz sub-harmonic Gilbert mixer is demonstrated in this paper using the 0.35 µm SiGe BiCMOS technology. The time-delay when the sub-harmonic LO (Local Oscillator) stage generates sub-harmonic LO signals is compensated by using fully symmetrical multiplier pairs. High RF-to-IF isolation and sub-harmonic LO Gilbert cell with excellent frequency response can be achieved by the elimination of the time-delay. The SiGe BiCMOS sub-harmonic micromixer exhibits 17 dB conversion gain, -74 dB 2LO-to-RF isolation, IP1 dB of -20 dBm, and IIP3 of -10 dBm. The measured double sideband noise figure is 16 dB from 100-kHz to 100-MHz because the SiGe bipolar device has very low 1/f noise corner.

This paper proposes new resource management schemes for multiple data streams in an orthogonal frequency and space division multiplex access (OFSDMA) system using Radio-on-Fiber (RoF) ubiquitous antennas. The proposed schemes classify the services into some classes in which the number of sub-carriers is dynamically assigned according to the requested data size. The computer simulation results show that the proposed schemes improve the number of users satisfying the required bit error rate (BER) level as well as the average throughput and also show that the RoF ubiquitous antennas can improve system capacity.

A 5.2 GHz 1 dB conversion gain, IP1 dB = -19 dBm and IIP3= -9 dBm double quadrature Gilbert downconversion mixer with polyphase filters is demonstrated by using 0.35 µm SiGe HBT technology. The image rejection ratio is better than 47 dB when LO=5.17 GHz and IF is in the range of 15 MHz to 45 MHz. The Gilbert downconverter has four-stage RC-CR IF polyphase filters for the image rejection. Polyphase filters are also used to generate LO and RF quadrature signals around 5 GHz in the double quadrature downconverter.

Menger's sponge (MS) is a kind of three-dimensional fractal structure. To analyze non-resonant electromagnetic properties of MS composed of isotropic paraelectric material, a novel, high-speed computation method employing simple recursion equations in terms of scattering amplitudes for two MS's with adjacent stage numbers, which are the parameters describing structural differences of MS's, is formulated. Within the scope of non-resonant electromagnetic phenomena, scattering patterns, forward and backward scattering amplitudes, and total cross sections of MS are investigated as a function of stage number and incident plane waves, and behaviors typical to fractal structures are extracted from the numerical results of the above equations. In addition, scattering properties at infinite stage number are discussed.

This paper reports on a fiber-optic system for in-building wireless communication/broadcast systems developed in Samsung Electronics. Our system delivers the third generation mobile system, satellite-digital multimedia broadcast, and wireless local access network services over a single strand of single-mode fiber or multi-mode fiber. We present the design issue and experimental results of the radio-over-fiber link.

We propose a simple technique to form miniature optical circuits using microfibers embedded into a low refractive index matrix. As an example we demonstrate a silica microfiber knot resonator embedded in a fluoroacrylate polymer. Fabrication issues and initial experimental results are reported. We also present simulations aimed at understanding the current limitations to the Q-factor and the role of the embedding polymer refractive index on the Q-factor of future resonators. It is anticipated that using commercially available polymers high Q-factor resonators with radii as small as 100 micrometers can be made by this technique.

Sequences with good correlation properties are widely used in engineering applications, especially in the area of communications. Among the known sequences, cyclotomic families have the optimal autocorrelation property. In this paper, we decide the cross-correlation function of the known cyclotomic sequences completely. Moreover, to get our results, the relations between the multiplier group and the decimations of the characteristic sequence are also established for an arbitrary difference set.

Using a pair of matched square-root-raised-cosine (SRRC) filters in the transmitter and the receiver in a band-limited digital communication system can theoretically achieve zero inter-symbol interference (ISI). In reality, the ISI cannot be zero when both SRRC filters are approximately implemented because of some numerical precision problems in the design phase as well as in the implementation phase. In this paper, the author proposes an iterative method to design the coefficients of SRRC FIR filters. The required ISI of the system can be specified such that both ISI and frequency domain specifications are monitored in the design phase. Since the ISI can be specified beforehand, the tradeoff between performance and the filter length becomes possible in the proposed design algorithm.

In this paper, we describe detailed experimental demonstrations of blue/violet light generation by the injection of ultrashort optical pulses into photonic crystal fibers (PCFs). Two lightwaves appear one on each side of the injected pulses in the spectral domain. They simultaneously evolve in the PCFs, changing their center wavelengths so as to spectrally stand apart from each other. Such behaviors are explained on the basis of the theory of nonlinear optics. The final center-wavelength difference between the two lightwaves at the end of the PCFs, depending on the power density of the injected pulse, is increased up to a limit imposed by the PCFs. Owing to this increase, the shorter wavelength limit reaches approximately 400 nm, which shows that short-pulse injection in PCFs is a promising method of realizing simple blue/violet light sources.

A nonlinear optical fiber loop mirror (NOLM) adapted for all-optical 2R operation at ultrahigh bit-rates was experimentally and theoretically investigated. The proposed NOLM was created by adding inline/external fiber polarizers and also an inline optical phase-bias compensator (OPBC) to a standard NOLM. A theoretical investigation revealed that the operation of the standard NOLM became unstable due to residual polarization crosstalk of the polarization-maintaining optical components making up the NOLM, and that it could be dramatically improved with the inline/external polarizers. The NOLM with the polarizers ensured stable switching operation with high switching-dynamic-range (>30 dB) against the change of the wavelength of the input clock pulses, and the change of the environment temperature. We also experimentally verified that the OPBC played a dramatic role to ensure excellent dynamic switching performance of the NOLM, and to achieve signal-Q-recovery of the regenerated signals. All optical 2R experiments at 40 Gb/s and 160 Gb/s were performed with the modified NOLM. Signal regeneration with improved extinction ratio and signal Q value was successfully demonstrated. Q-recovery to the input of the control pulses degraded with ASE noise accumulation was also successfully achieved.

This letter presents an efficient Signed-Power-of-Two (SPT) term allocation for filter coefficients in order to improve the BER characteristics of digital communication systems. The performance of the present allocation is evaluated by BER characteristics through digital modulation simulations and FPGA-based digital implementation.

This paper presents a scheme for accurately detecting the number of incident waves arriving at array antennas. The array antenna and MIMO techniques are developing as 4th generation mobile communication systems and wireless LAN technologies, and the accurate estimation of the propagation environment is becoming more important. This paper emphasizes the accurate detection of the number of incident waves; one of the important characteristics in multidirectional communication. There are some recent papers on accurate detection but they have problems of estimation accuracy or computational cost in severe environment like low SNR, small number of snapshots or waves with close angles. Hence, AIC and MDL methods based on statistics and information theory are still often used. In this paper, we propose an accurate estimation method of the number of arrival signals using the orthogonality of subspaces derived from preliminary estimation of signal subspace. The proposed method accurately estimates the number of signals also in severe environments where AIC and MDL methods can hardly estimate. We evaluate the performance of these methods through some computer simulation and experiments in anechoic chamber.

The wave absorber which is formed by arranging cylindrical bars periodically composed of magnetic loss material and metallic bars is proposed for improving ETC environment, and characteristics of reflection loss and shielding effect are analyzed and measured. As a result, the change of various characteristics can be confirmed quantitatively by changing the thickness of magnetic loss material covering around a metallic bar and the pitch interval between bars. Furthermore, it is clarified that reflection loss of -9 dB and shielding effect of -25 dB are obtained at 5.8 GHz when the covering thickness of material is 1.5 mm and the pitch interval is 16.0 mm. Therefore, the wave absorber formed by arranging cylindrical bars that satisfies various characteristics required for the improvement of ETC environment can be realized.

This paper investigates the impact of chip duty factor (DF) in DS-UWB system with Rake receiver over AWGN and UWB indoor multipath environment corresponding to system parameters such as spreading bandwidth and chip length. Manipulating DF in DS-UWB system offers several advantages over multipath channel and thus, capable of improving system performance for better quality of communication. Although employing lower DF generally improves performance, in some exceptional cases on the other hand, degradation can be observed despite decreasing DF. Therefore, the objective of this paper is to clarify the relationship between DF and DS-UWB system performance. We discovered that with constant processing gain and spreading bandwidth, performance improvement can be observed at DF lower than 0.17. Additionally, with spreading bandwidth as tradeoff parameter, significant performance improvement can only be observed below DF of 0.85.

This paper presents an algorithm-level interpretation of fast adder structures in binary/multiple-valued logic. The key idea is to employ a unified representation of addition algorithms called Counter Tree Diagrams (CTDs). The use of CTDs makes it possible to describe and analyze addition algorithms at various levels of abstraction. A high-level CTD represents a network of coarse-grained components associated with multiple-valued logic devices, while a low-level CTD represents a network of primitive components directly mapped onto binary logic devices. The level of abstraction in circuit representation can be changed by decomposition of CTDs. We can derive possible variations of adder structures by decomposing a high-level CTD into low-level CTDs. This paper demonstrates the interpretation of redundant arithmetic adders based on CTDs. We first introduce an extension of CTDs to represent possible redundant arithmetic adders with limited carry propagation. Using the extended version of CTDs, we can classify the conventional adder structures including those using emerging devices into three types in a systematic way.