The optical phased array (OPA) is an emerging non-mechanical device that enables high-speed beam steering by emitting precisely phase-controlled lightwaves from numerous optical antennas. In practice, however, it is challenging to drive all phase shifters on an OPA in a deterministic manner due to the inevitable fabrication-induced phase errors and crosstalk between the phase shifters. In this work, we fabricate a 16-element silicon photonic non-redundant OPA chip with integrated phase monitors and experimentally demonstrate accurate monitoring of the relative phases of light from each optical antenna. Under the beam steering condition, the optical phase retrieved from the on-chip phase monitors varies linearly with the steering angle, as theoretically expected.

One of cost-effective ways to increase the transmission capacity of current standard wavelength division multiplexing (WDM) transmission systems is to use a wavelength band other than the C-band to transmit in multi-band. We proposed the concept of multi-band system using wavelength conversion, which can simultaneously process signals over a wide wavelength range. All-optical wavelength conversion could be used to convert C-band WDM signals into other bands in a highly nonlinear fiber (HNLF) by four-wave mixing and allow to simultaneously transmit multiple WDM signals including other than the C-band, with only C-band transceivers. Wavelength conversion has been reported for various nonlinear waveguide materials other than HNLF. In such nonlinear materials, we noticed the possibility of wideband transmission by dispersion-tailored silicon-on-insulator (SOI) waveguides. Based on the CMOS process has high accuracy, it is expected that the chromatic dispersion fluctuation could be reduced in mass production. As a first step in the investigation of the broadness of wavelength conversion using SOI-based waveguides, we designed and fabricated dispersion-tailored 12 strip waveguides provided with an edge coupler at both ends. Each of the 12 waveguides having different widths and lengths and is connected to fibers via lensed fibers or by lenses. In order to characterize each waveguide, the pump-probe experimental setup was constructed using a tunable light source as pump and an unmodulated 96-ch C-band WDM test signal. Using this setup, we evaluate insertion loss, input power dependence, conversion bandwidth and conversion efficiency. We confirmed C-band test signal was converted to the S-band and the L-band using the same silicon waveguide with 3dB conversion bandwidth over 100-nm. Furthermore, an increased design tolerance of at least 90nm was confirmed for C-to-S conversion by shortening the waveguide length. It is confirmed that the wavelength converters using the nonlinear waveguide has sufficiently wide conversion bandwidth to enhance the multi-band WDM transmission system.

We propose a novel mode-multiplexed light source using angularly-multiplexed volume holograms. Mode division multiplexing beams can be generated from a simple transmitter that is made of a laser array, single lens, and volume holograms. Hologram media has low recording sensitivity; hence, using holograms in the communication band is difficult. However, a dual wavelength method that uses different wavelengths for recording and reading holograms can realize the volume holograms for the infrared region. The volume holograms for three spatial mode multiplexing are formed using a compact Michelson interferometer type recording setup; simultaneous generations of three modes were demonstrated using a fiber array or vertical cavity surface emitting laser array with the volume holograms. A low loss coupling of three modes to few-mode-fiber can be achieved through the precise design and recording of volume holograms. The simple and low-cost mode-multiplexed light source using the volume holograms has the potential to broaden the application of MDM.

The maximal independent set (MIS) problem is one of the most fundamental problems in the field of distributed computing. This paper focuses on the MIS problem with unreliable communication between processes in the system. We propose a relaxed notion of MIS, named almost MIS (ALMIS), and show that the loosely-stabilizing algorithm proposed in our previous work can achieve exponentially long holding time with logarithmic convergence time and space complexity regarding ALMIS, which cannot be achieved at the same time regarding MIS in our previous work.

The Variational Quantum Eigensolver (VQE) algorithm is gaining interest for its potential use in near-term quantum devices. In the VQE algorithm, parameterized quantum circuits (PQCs) are employed to prepare quantum states, which are then utilized to compute the expectation value of a given Hamiltonian. Designing efficient PQCs is crucial for improving convergence speed. In this study, we introduce problem-specific PQCs tailored for optimization problems by dynamically generating PQCs that incorporate problem constraints. This approach reduces a search space by focusing on unitary transformations that benefit the VQE algorithm, and accelerate convergence. Our experimental results demonstrate that the convergence speed of our proposed PQCs outperforms state-of-the-art PQCs, highlighting the potential of problem-specific PQCs in optimization problems.

FPGA clusters that consist of multiple FPGA boards have been gaining interest in recent times. Massively parallel processing with a stand-alone heterogeneous FPGA cluster with SoC- style FPGAs and mid-scale FPGAs is promising with cost-performance benefit. Here, we propose such a heterogeneous FPGA cluster with FiC and M-KUBOS cluster. FiC consists of multiple boards, mounting middle scale Xilinx's FPGAs and DRAMs, which are tightly coupled with high-speed serial links. In addition, M-KUBOS boards are connected to FiC for ensuring high IO data transfer bandwidth. As an example of massively parallel processing, here we implement genomic pattern search. Next-generation sequencing (NGS) technology has revolutionized biological system related research by its high-speed, scalable and massive throughput. To analyze the genomic data, short read mapping technique is used where short Deoxyribonucleic acid (DNA) sequences are mapped relative to a known reference sequence. Although several pattern matching techniques are available, FM-index based pattern search is perfectly suitable for this task due to the fastest mapping from known indices. Since matching can be done in parallel for different data, the massively parallel computing which distributes data, executes in parallel and gathers the results can be applied. We also implement a data compression method where about 10 times reduction in data size is achieved. We found that a M-KUBOS board matches four FiC boards, and a system with six M-KUBOS boards and 24 FiC boards achieved 30 times faster than the software based implementation.

An interconnection network is an inevitable component for constructing parallel computers. It connects computation nodes so that the nodes can communicate with each other. As a parallel computation essentially requires inter-node communication according to a parallel algorithm, the interconnection network plays an important role in terms of communication performance. This paper focuses on the collective communication that is frequently performed in parallel computation and this paper addresses the Cup-Stacking method that is proposed in our preceding work. The key issues of the method are splitting a large packet into slices, re-shaping the slice, and stacking the slices, in a genetic algorithm (GA) manner. This paper discusses extending the Cup-Stacking method by introducing additional items (genes) and proposes the extended Cup-Stacking method. Furthermore, this paper places comprehensive discussions on the drawbacks and further optimization of the method. Evaluation results reveal the effectiveness of the extended method, where the proposed method achieves at most seven percent improvement in duration time over the former Cup-Stacking method.

We assess how well the recently created MRI reconstruction technique, Multi-Resolution Convolutional Neural Network (MRCNN), performs in the core medical vision field (classification). The primary goal of MRCNN is to identify the best k-space undersampling patterns to accelerate the MRI. In this study, we use the Figshare brain tumor dataset for MRI classification with 3064 T1-weighted contrast-enhanced MRI (CE-MRI) over three categories: meningioma, glioma, and pituitary tumors. We apply MRCNN to the dataset, which is a method to reconstruct high-quality images from under-sampled k-space signals. Next, we employ the pre-trained VGG16 model, which is a Deep Neural Network (DNN) based image classifier to the MRCNN restored MRIs to classify the brain tumors. Our experiments showed that in the case of MRCNN restored data, the proposed brain tumor classifier achieved 92.79% classification accuracy for a 10% sampling rate, which is slightly higher than that of SRCNN, MoDL, and Zero-filling methods have 91.89%, 91.89%, and 90.98% respectively. Note that our classifier was trained using the dataset consisting of the images with full sampling and their labels, which can be regarded as a model of the usual human diagnostician. Hence our results would suggest MRCNN is useful for human diagnosis. In conclusion, MRCNN significantly enhances the accuracy of the brain tumor classification system based on the tumor location using under-sampled k-space signals.

Learning analytics (LA) has emerged as a technique for educational quality improvement in many learning contexts, including blended learning (BL) courses. Numerous studies show that students' academic performance is significantly impacted by their ability to engage in self-regulated learning (SRL). In this study, learning behaviors indicating SRL and motivation are elucidated during a BL course on second language learning. Online trace data of a mobile language learning application (m-learning app) is used as a part of BL implementation. The observed motivation were of two categories: high-level motivation (study in time, study again, and early learning) and low-level motivation (cramming and catch up). As a result, students who perform well tend to engage in high-level motivation. While low performance students tend to engage in clow-level motivation. Those findings are supported by regression models showing that study in time followed by early learning significantly influences the academic performance of BL courses, both in the spring and fall semesters. Using limited resource of m-learning app log data, this BL study could explain the overall BL performance.

In this study, we present a spherical style deformation algorithm to be applied on single component models that can deform the models with spherical style, while preserving the local details of the original models. Because 3D models have complex skeleton structures that consist of many components, the deformation around connections between each single component is complicated, especially preventing mesh self-intersections. To the best of our knowledge, there does not exist not only methods to achieve a spherical style in a 3D model consisting of multiple components but also methods suited to a single component. In this study, we focus on spherical style deformation of single component models. Accordingly, we propose a deformation method that transforms the input model with the spherical style, while preserving the local details of the input model. Specifically, we define an energy function that combines the as-rigid-as-possible (ARAP) method and spherical features. The spherical term is defined as l2-regularization on a linear feature; accordingly, the corresponding optimization can be solved efficiently. We also observed that the results of our deformation are dependent on the quality of the input mesh. For instance, when the input mesh consists of many obtuse triangles, the spherical style deformation method fails. To address this problem, we propose an optional deformation method based on convex hull proxy model as the complementary deformation method. Our proxy method constructs a proxy model of the input model and applies our deformation method to the proxy model to deform the input model by projection and interpolation. We have applied our proposed method to simple and complex shapes, compared our experimental results with the 3D geometric stylization method of normal-driven spherical shape analogies, and confirmed that our method successfully deforms models that are smooth, round, and curved. We also discuss the limitations and problems of our algorithm based on the experimental results.

This paper describes a public web service called Kiite Cafe that lets users get together virtually to listen to music. When users listen to music on Kiite Cafe, their experiences are enhanced by two architectures: (i) visualization of each user's reactions, and (ii) selection of songs from users' favorite songs. These architectures enable users to feel social connection with others and the joy of introducing others to their favorite songs as if they were together listening to music in person. In addition, the architectures provide three user experiences: (1) motivation to react to played songs, (2) the opportunity to listen to a diverse range of songs, and (3) the opportunity to contribute as a curator. By analyzing the behavior logs of 2,399 Kiite Cafe users over a year, we quantitatively show that these user experiences can generate various effects (e.g., users react to a more diverse range of songs on Kiite Cafe than when listening alone). We also discuss how our proposed architectures can enrich music listening experiences with others.

Until today, digital image watermarking has not been large-scale used in the industry. The first reason is that the watermarking efficiency is low and the real-time performance cannot be satisfied. The second reason is that the watermarking scheme cannot cope with various attacks. To solve above problems, this paper presents a multi-domain based digital image watermarking scheme, where a fast DFT (Discrete Fourier Transform) based watermarking method is proposed for synchronization correction and an IWT-DCT (Integer Wavelet Transform-Discrete Cosine Transform) based watermarking method is proposed for information embedding. The proposed scheme has high efficiency during embedding and extraction. Compared with five existing schemes, the robustness of our scheme is very strong and our scheme can cope with many common attacks and compound attacks, and thus can be used in wide application scenarios.

The diffusion model has achieved success in generating and editing high-quality images because of its ability to produce fine details. Its superior generation ability has the potential to facilitate more detailed segmentation. This study presents a novel approach to segmentation tasks using an inverse heat dissipation model, a kind of diffusion-based models. The proposed method involves generating a mask that gradually shrinks to fit the shape of the desired segmentation region. We comprehensively evaluated the proposed method using multiple datasets under varying conditions. The results show that the proposed method outperforms existing methods and provides a more detailed segmentation.

This letter presents a global feature-based method for evaluating the no reference quality of scanning electron microscopy (SEM) contrast-distorted images. Based on the characteristics of SEM images and the human visual system, the global features of SEM images are extracted as the score for evaluating image quality. In this letter, the texture information of SEM images is first extracted using a low-pass filter with orientation, and the amount of information in the texture part is calculated based on the entropy reflecting the complexity of the texture. The singular values with four scales of the original image are then calculated, and the amount of structural change between different scales is calculated and averaged. Finally, the amounts of texture information and structural change are pooled to generate the final quality score of the SEM image. Experimental results show that the method can effectively evaluate the quality of SEM contrast-distorted images.

The design of codes for distributed storage systems that protects from node failures has been studied for years, and locally repairable code (LRC) is such a method that gives a solution for fast recovery of node failures. Linear complementary dual code (LCD code) is useful for preventing malicious attacks, which helps to secure the system. In this paper, we combine LRC and LCD code by integration of enhancing security and repair efficiency, and propose some techniques for constructing LCD codes with their localities determined. On the basis of these methods and inheriting previous achievements of optimal LCD codes, we give optimal or near-optimal [n, k, d;r] LCD codes for k≤6 and n≥k+1 with relatively small locality, mostly r≤3. Since all of our obtained codes are distance-optimal, in addition, we show that the majority of them are r-optimal and the other 63 codes are all near r-optimal, according to CM bound.

Mission-critical monitoring services, such as finding criminals with a monitoring camera, require rapid detection of newly updated data, where suppressing delay is desirable. Taking this direction, this paper proposes a network design scheme to minimize this delay for monitoring services that consist of Internet-of-Things (IoT) devices located at terminal endpoints (TEs), databases (DB), and applications (APLs). The proposed scheme determines the allocation of DB and APLs and the selection of the server to which TE belongs. DB and APL are allocated on an optimal server from multiple servers in the network. We formulate the proposed network design scheme as an integer linear programming problem. The delay reduction effect of the proposed scheme is evaluated under two network topologies and a monitoring camera system network. In the two network topologies, the delays of the proposed scheme are 78 and 80 percent, compared to that of the conventional scheme. In the monitoring camera system network, the delay of the proposed scheme is 77 percent compared to that of the conventional scheme. These results indicate that the proposed scheme reduces the delay compared to the conventional scheme where APLs are located near TEs. The computation time of the proposed scheme is acceptable for the design phase before the service is launched. The proposed scheme can contribute to a network design that detects newly added objects quickly in the monitoring services.

The performance of a fully wireless-power-transfer (WPT) node network, in which each node transfers (and receives) energy through a wireless channel when it has sufficient (and insufficient) energy in its battery, was theoretically analyzed. The lost job ratio (LJR), namely, is the ratio of (i) the amount of jobs that cannot be done due to battery of a node running out to (ii) the amount of jobs that should be done, is used as a performance metric. It describes the effect of the battery of each node running out and how much additional energy is needed. Although it is known that WPT can reduce the probability of the battery running out among a few nodes within a small area, the performance of a fully WPT network has not been clarified. By using stochastic geometry and first-passage-time analysis for a diffusion process, the expected LJR was theoretically derived. Numerical examples demonstrate that the key parameters determining the performance of the network are node density, threshold switching of statuses between “transferring energy” and “receiving energy,” and the parameters of power conversion. They also demonstrate the followings: (1) The mean energy stored in the node battery decreases in the networks because of the loss caused by WPT, and a fully WPT network cannot decrease the probability of the battery running out under the current WPT efficiency. (2) When the saturation value of power conversion increases, a fully WPT network can decrease the probability of the battery running out although the mean energy stored in the node battery still decreases in the networks. This result is explained by the fact that the variance of stored energy in each node battery becomes smaller due to transfer of energy from nodes of sufficient energy to nodes of insufficient energy.

In the current heterogeneous wireless communication system, the sharp rise in energy consumption and the emergence of new service types pose great challenges to nowadays radio access network selection algorithms which do not take care of these new trends. So the proposed energy efficiency based multi-service heterogeneous access network selection algorithm-ESRS (Energy Saving Radio access network Selection) is intended to reduce the energy consumption caused by the traffic in the mobile network system composed of Base Stations (BSs) and Access Points (APs). This algorithm models the access network selection problem as a Multiple-Attribute Decision-Making (MADM) problem. To solve this problem, lots of methods are combined, including analytic Hierarchy Process (AHP), weighted grey relational analysis (GRA), entropy theory, simple additive weight (SAW), and utility function theory. There are two main steps in this algorithm. At first, the proposed algorithm gets the result of the user QoS of each network by dealing with the related QoS parameters, in which entropy theory and AHP are used to determine the QoS comprehensive weight, and the SAW is used to get each network's QoS. In addition to user QoS, parameters including user throughput, energy consumption utility and cost utility are also calculated in this step. In the second step, the fuzzy theory is used to define the weight of decision attributes, and weighted grey relational analysis (GRA) is used to calculate the network score, which determines the final choice. Because the fuzzy weight has a preference for the low energy consumption, the energy consumption of the traffic will be saved by choosing the network with the least energy consumption as much as possible. The simulation parts compared the performance of ESRS, ABE and MSNS algorithms. The numerical results show that ESRS algorithm can select the appropriate network based on the service demands and network parameters. Besides, it can effectively reduce the system energy consumption and overall cost while still maintaining a high overall QoS value and a high system throughput, when compared with the other two algorithms.

This paper proposes a virtual network function (VNF) placement model considering both availability and probabilistic protection for the service delay to minimize the service deployment cost. Both availability and service delay are key requirements of services; a service provider handles the VNF placement problem with the goal of minimizing the service deployment cost while meeting these and other requirements. The previous works do not consider the delay of each route which the service can take when considering both availability and delay in the VNF placement problem; only the maximum delay was considered. We introduce probabilistic protection for service delay to minimize the service deployment cost with availability. The proposed model considers that the probability that the service delay, which consists of networking delay between hosts and processing delay in each VNF, exceeds its threshold is constrained within a given value; it also considers that the availability is constrained within a given value. We develop a two-stage heuristic algorithm to solve the VNF placement problem; it decides primary VNF placement by solving mixed-integer second-order cone programming in the first stage and backup VNF placement in the second stage. We observe that the proposed model reduces the service deployment cost compared to a baseline that considers the maximum delay by up to 12%, and that it obtains a feasible solution while the baseline does not in some examined situations.

In this study, aiming at clarifying the characteristics of air-to-ground radio wave propagation in mountainous areas, a transmission experiment was performed between a drone equipped with a transmitter and three receivers set up on the ground using a 920MHz band wireless system at Uchigatani forest, which is located in Yamato-cho, Gujo-shi, Gifu Prefecture. In the experiment, we simultaneously measured the received signal strength indicator (RSSI) and the drone's latitude, longitude, and height from the ground. Then, we verified whether the measured data has the line-of-sight between the transmitter and receivers using a geographic information system and analyzed characteristics of the RSSI, packet loss rate, and fading concerning the height from the ground and distance between the transmitter and receivers. The results showed that increasing the drone's altitude to 90m or more makes the link more stable and that the fading distribution in mountainous terrains is different from in other terrains.